Searched refs:and (Results 3801 – 3825 of 3855) sorted by relevance
1...<<151152153154155
| /Zephyr-latest/boards/st/stm32h7b3i_dk/ |
| D | stm32h7b3i_dk.dts | 182 /* Connect solder bridges SB3, SB4 and SB5 to use CAN connector (CN21) */
|
| /Zephyr-latest/dts/arm/nxp/ |
| D | nxp_rt5xx_common.dtsi | 74 * between code and data. Boards can
114 * addresses differ between non-secure (0x40000000) and secure
|
| D | nxp_imx7d_m4.dtsi | 162 /* For now only uart2 is supported and
|
| /Zephyr-latest/dts/arm/nordic/ |
| D | nrf5340_cpunet.dtsi | 106 * is added and set as the default Bluetooth Controller.
|
| D | nrf52805.dtsi | 101 * is added and set as the default Bluetooth Controller.
|
| D | nrf52810.dtsi | 105 * is added and set as the default Bluetooth Controller.
|
| D | nrf52811.dtsi | 117 * is added and set as the default Bluetooth Controller.
|
| D | nrf52820.dtsi | 119 * is added and set as the default.
|
| /Zephyr-latest/dts/riscv/ite/ |
| D | it8xxx2-wuc-map.dtsi | 10 /* Mapping between wuc bits and source device */
|
| /Zephyr-latest/tests/drivers/build_all/adc/boards/ |
| D | native_sim.overlay | 10 * (and be extended to test) real hardware.
|
| /Zephyr-latest/cmake/linker/iar/ |
| D | config_file_script.cmake | 522 # section patterns and blocks to keep { }
597 # Get the next offset and use that as this ones size!
681 # the `.text' and `.rdata' input sections will appear in the output section.
814 # Generate the _init block and the initialize manually statement.
|
| /Zephyr-latest/dts/xtensa/intel/ |
| D | intel_adsp_ace15_mtpm.dtsi | 181 * not fully represent hardware capabilities and is expected to be modified.
543 * controllers, but the special setup and extra
|
| /Zephyr-latest/dts/arm/st/h7/ |
| D | stm32h7.dtsi | 847 * resolution 14 and 12 shall be replaced, respectively, by
848 * STM32_ADC_RES(14, 0x01) and STM32_ADC_RES(12, 0x02)
886 /* dual mode: adc1 and adc2 coupled */
|
| /Zephyr-latest/dts/arm/ambiq/ |
| D | ambiq_apollo4p_blue.dtsi | 178 /* IOM4 works as SPI and is wired internally for BLE HCI. */
|
| /Zephyr-latest/dts/arm/renesas/smartbond/ |
| D | da1469x.dtsi | 2 * Copyright (c) 2022 Renesas Electronics Corporation and/or its affiliates
|
| /Zephyr-latest/cmake/linker_script/common/ |
| D | common-rom.cmake | 45 # https://developer.arm.com/documentation/dui0378/g/The-ARM-C-and-C---Libraries
|
| /Zephyr-latest/dts/arm/st/l4/ |
| D | stm32l4p5.dtsi | 14 /* total SRAM 320KB for the stm32L4P5x and stm32L4Q5x */
|
| /Zephyr-latest/modules/hal_nordic/nrfx/ |
| D | CMakeLists.txt | 199 # Inject code to skip TAMPC setup for nRF54L20 and nRF54L09. It is not supported for now.
|
| /Zephyr-latest/boards/nxp/vmu_rt1170/ |
| D | vmu_rt1170_mimxrt1176_cm7.dts | 475 /* GPT and Systick are enabled. If power management is enabled, the GPT
|
| /Zephyr-latest/drivers/bluetooth/hci/ |
| D | hci_spi_st.c | 68 #warning CONFIG_BT_L2CAP_TX_MTU is too large and can result in packets that cannot \
|
| /Zephyr-latest/soc/nxp/imxrt/imxrt7xx/hifi4/ |
| D | linker.ld | 306 /* C++ constructor and destructor tables, properly ordered: */
|
| /Zephyr-latest/soc/nxp/imxrt/imxrt7xx/hifi1/ |
| D | linker.ld | 312 /* C++ constructor and destructor tables, properly ordered: */
|
| /Zephyr-latest/dts/arm/microchip/ |
| D | mec172x_common.dtsi | 804 /* reg tuple contains one 32-bit address cell and one
973 /* Capture writes to an 8-bit I/O and map to one of 0x80 to 0x83 */
|
| /Zephyr-latest/dts/arm/silabs/xg29/ |
| D | xg29.dtsi | 151 * The minimum residency and exit latency is
|
| /Zephyr-latest/cmake/linker/ |
| D | linker_script_common.cmake | 45 # Already the right type, so just set and return.
498 # - Ordered list of all sections for easier retrieval on printing and configuration.
|
1...<<151152153154155
