Searched full:ldo (Results 1 – 25 of 63) sorted by relevance
123
| /Zephyr-latest/soc/st/stm32/ |
| D | Kconfig | 66 bool "LDO supply"
72 bool "SMPS 1.8V supplies LDO (no external supply)"
76 bool "SMPS 2.5V supplies LDO (no external supply)"
80 bool "External SMPS 1.8V supply, supplies LDO"
84 bool "External SMPS 2.5V supply, supplies LDO"
|
| /Zephyr-latest/dts/bindings/regulator/ |
| D | renesas,da1469x-regulator.yaml | 5 Renesas Smartbond(tm) LDO and DCDC regulators
22 Selects reference source for V30 LDO to Bandgap output.
43 renesas,regulator-sleep-ldo:
46 Enable LDO in sleep mode.
|
| D | nordic,npm2100-regulator.yaml | 7 The PMIC has one boost converter and one LDO/LDSW.
|
| /Zephyr-latest/soc/nxp/imxrt/imxrt11xx/ |
| D | Kconfig | 68 bool "Bypass LDO lpsr"
71 bool "Adjust LDO setting"
|
| /Zephyr-latest/soc/espressif/common/ |
| D | Kconfig.flash | 95 bool "VDDSDIO LDO voltage"
99 If this option is enabled, and VDDSDIO LDO is set to 1.8V (using eFuse
100 or MTDI bootstrapping pin), bootloader will change LDO settings to
|
| /Zephyr-latest/include/zephyr/dt-bindings/regulator/ |
| D | max20335.h | 20 /** LDO mode */
|
| D | nrf5x.h | 19 /** LDO mode */
|
| D | npm1300.h | 25 /* LDSW / LDO modes */
|
| /Zephyr-latest/soc/intel/intel_adsp/cavs/ |
| D | power_down_cavs.S | 84 /* mandatory sequence for LDO ON - effectively executes:
117 /* mandatory sequence for LDO OFF - effectively executes:
|
| /Zephyr-latest/boards/norik/octopus_io_board/doc/ |
| D | index.rst | 35 * LDO regulator to power Octopus SoM and peripherals
81 …a built-in LDO regulator that is used to power the Octopus SoM and peripherals. The EN2 pin can be…
|
| /Zephyr-latest/boards/espressif/esp32s3_eye/doc/ |
| D | index.rst | 49 …on, it indicates either the USB power is not supplied, or the 5 V to 3.3 V LDO is broken. Software…
54 - 5 V to 3.3 V LDO
72 - 3.3 V to 1.5 V LDO
75 - 3.3 V to 2.8 V LDO
|
| /Zephyr-latest/soc/intel/intel_adsp/ace/include/ace15_mtpm/ |
| D | adsp_shim.h | 100 /* LDO Control */
168 /** LDO Control */
|
| /Zephyr-latest/soc/intel/intel_adsp/ace/include/ace20_lnl/ |
| D | adsp_shim.h | 100 /* LDO Control */
162 /** LDO Control */
|
| /Zephyr-latest/soc/atmel/sam0/common/ |
| D | Kconfig.saml2x | 58 Note, this mode can only be used with an LDO regulator.
|
| /Zephyr-latest/dts/arm/renesas/smartbond/ |
| D | da1469x.dtsi | 108 renesas,regulator-sleep-ldo;
135 renesas,regulator-sleep-ldo;
141 renesas,regulator-sleep-ldo;
|
| /Zephyr-latest/boards/st/steval_stwinbx1/ |
| D | steval_stwinbx1.dts | 128 /* Enable 2.7V Analog LDO */
129 ldo-enable-gpios {
|
| /Zephyr-latest/drivers/adc/ |
| D | adc_smartbond_gpadc.c | 308 /* Disable the GPADC LDO */ in gpadc_smartbond_resume()
327 /* Disable the GPADC LDO */ in gpadc_smartbond_suspend()
|
| D | adc_smartbond_sdadc.c | 152 /* Wait until the SDADC LDO stabilizes */ in adc_context_start_sampling()
331 /* Disable the sdadc LDO */ in sdadc_smartbond_suspend()
|
| /Zephyr-latest/drivers/usb_c/ppc/ |
| D | nxp_nx20p3483_priv.h | 124 /** Bit field for LDO shutdown */
|
| /Zephyr-latest/soc/intel/intel_adsp/ace/include/ace30/ |
| D | adsp_shim.h | 123 /** LDO Control */
|
| /Zephyr-latest/soc/intel/intel_adsp/cavs/include/cavs25/ |
| D | adsp_shim.h | 126 /** LDO Control */
|
| /Zephyr-latest/boards/particle/nrf51_blenano/doc/ |
| D | index.rst | 54 It also regulates 5V from USB to 3.3V via the onboard LDO to power Nano.
|
| /Zephyr-latest/boards/nxp/hexiwear/ |
| D | hexiwear_mk64f12.dts | 72 en_ldo: enable-ldo {
|
| /Zephyr-latest/boards/particle/nrf52_blenano2/doc/ |
| D | index.rst | 54 It also regulates 5V from USB to 3.3V via the onboard LDO to power Nano v2.
|
| /Zephyr-latest/drivers/mfd/ |
| D | mfd_axp192.c | 218 /* LDO is only applicable on GPIO0 */ in mfd_axp192_gpio_func_get()
331 /* LDO is only applicable on GPIO0 */ in mfd_axp192_gpio_func_ctrl()
|
123
