Searched refs:wire (Results 26 – 50 of 124) sorted by relevance
12345
| /Zephyr-latest/doc/hardware/peripherals/ |
| D | espi.rst | 10 based on SPI. It also features a four-wire interface (receive, transmit, clock
|
| /Zephyr-latest/boards/bytesatwork/bytesensi_l/ |
| D | bytesensi_l.dts | 73 /* Enable 1-wire to enable i2c bus as well */
74 one-wire-gpio {
|
| /Zephyr-latest/boards/shields/adafruit_data_logger/doc/ |
| D | index.rst | 46 .. [1] The user LEDs are not connected to ``D3`` and ``D4`` by default. Jumper or jumper wire
51 wire connection must be established between the ``SQ`` pin and the ``Digital I/O 7`` pin in
|
| /Zephyr-latest/drivers/sensor/lm75/ |
| D | Kconfig | 12 Enable the driver for the LM75 digital temperature Sensor with 2-wire
|
| /Zephyr-latest/drivers/led_strip/ |
| D | Kconfig | 25 # for drivers which require 4 B on wire for every 3 B of color, e.g. APA102, but
|
| /Zephyr-latest/boards/shields/adafruit_data_logger/ |
| D | adafruit_data_logger.overlay | 61 * Interrupt connection must be manually established using a jumper wire between
|
| /Zephyr-latest/tests/drivers/regulator/voltage/boards/ |
| D | rpi_pico.overlay | 13 * Scraping the resist on there and soldering wire to make it able to measure by ADC.
|
| /Zephyr-latest/drivers/sensor/lm77/ |
| D | Kconfig | 13 Enable driver for the LM77 digital temperature sensor with 2-wire
|
| /Zephyr-latest/samples/drivers/spi_bitbang/ |
| D | README.rst | 23 You can connect the MISO and MOSI pins with a wire to provide a basic loopback
|
| /Zephyr-latest/samples/subsys/mgmt/osdp/ |
| D | README.rst | 12 Devices (PD) to a Control Panel (CP) over a two-wire RS-485 multi-drop serial
|
| /Zephyr-latest/doc/templates/ |
| D | sample.tmpl | 19 [For simple projects, a description of how to wire the board for the demo. For
|
| /Zephyr-latest/drivers/w1/ |
| D | Kconfig | 55 Enable 1-wire network layer
|
| /Zephyr-latest/boards/shields/adafruit_winc1500/doc/ |
| D | index.rst | 43 To enable low power support, wire the pin marked (b) to the En connector
|
| /Zephyr-latest/drivers/espi/ |
| D | Kconfig.npcx | 134 bool "Indicates that the eSPI hardware supports virtual wire GPIOs"
137 Selected if NPCX series supports virtual wire GPIOs in eSPI module.
|
| /Zephyr-latest/boards/shields/p3t1755dp_ard_i2c/doc/ |
| D | index.rst | 22 or shutdown mode. The device supports 2-wire serial I3C (up to 12.5 MHz)
|
| /Zephyr-latest/boards/shields/p3t1755dp_ard_i3c/doc/ |
| D | index.rst | 22 or shutdown mode. The device supports 2-wire serial I3C (up to 12.5 MHz)
|
| /Zephyr-latest/soc/microchip/mec/ |
| D | Kconfig | 230 bool "Debug support via Serial wire debug"
235 bool "Debug support via Serial wire debug with tracing enabled"
248 bool "Debug support via Serial wire debug"
|
| /Zephyr-latest/boards/ezurio/bl654_sensor_board/doc/ |
| D | bl654_sensor_board.rst | 150 | 2 | SWDIO | Serial wire data input/output pin | IN/OUT |
154 | 4 | SWCLK | Serial wire clock input pin | IN |
158 | 6 | SWO | Serial wire output pin | OUT |
|
| /Zephyr-latest/boards/shields/buydisplay_3_5_tft_touch_arduino/doc/ |
| D | index.rst | 14 current Zephyr driver only supports the 4-wire SPI interface.
|
| /Zephyr-latest/boards/adi/max32672evkit/ |
| D | max32672evkit.dts | 58 /* Enable D/C line for 4wire mode */
|
| /Zephyr-latest/drivers/bluetooth/hci/ |
| D | Kconfig.nxp | 85 data rate on Bluetooth?. 4-wire UART@3M baud is supported. PCM for
|
| /Zephyr-latest/boards/adi/max32680evkit/ |
| D | max32680evkit_max32680_m4.dts | 64 /* Enable D/C line for 4wire mode */
|
| /Zephyr-latest/boards/alientek/pandora_stm32l475/doc/ |
| D | index.rst | 78 - SWPMI single wire protocol master I/F
82 - Development support: serial wire debug (SWD), JTAG, Embedded Trace Macrocell |trade|
|
| /Zephyr-latest/boards/shields/inventek_eswifi/doc/ |
| D | index.rst | 50 recommendation is bend the NRST pin and make a wire to D6. WAKE-UP signal is
52 signal, user need do a wire connecting these two terminals. On the below
|
| /Zephyr-latest/boards/st/nucleo_l432kc/doc/ |
| D | index.rst | 75 - SWPMI single wire protocol master I/F
81 - Development support: serial wire debug (SWD), JTAG, Embedded Trace Macrocell*
|
12345
