Searched refs:SDIO (Results 1 – 25 of 83) sorted by relevance
1234
| /Zephyr-latest/tests/subsys/sd/sdio/ |
| D | README.txt | 1 SDIO Subsystem Test
4 This test is designed to verify the SD subsystem stack implementation for SDIO
5 devices. Note that this test will only perform basic reads from the SDIO card
7 specific. It requires an SDIO card be connected to the board to pass.
11 test the initialization flow of the SDIO subsystem to verify that the stack
12 can correctly initialize an SDIO card.
14 * Read test: verify that a read from the SDIO common card register area returns
|
| /Zephyr-latest/subsys/sd/ |
| D | Kconfig | 20 bool "SDIO protocol support"
22 Enable SDIO protocol support. Required for SD I/O cards to function.
75 # If SDIO is being used, need 512 bytes to read FUNC0 CIS
|
| /Zephyr-latest/boards/snps/iotdk/ |
| D | Kconfig.iotdk | 14 such as USB, UART, SPI, I2C, PWM, SDIO and ADCs.
|
| /Zephyr-latest/boards/infineon/cy8cproto_062_4343w/ |
| D | cy8cproto_062_4343w-pinctrl.dtsi | 44 /* Configure pin control bias mode for SDIO */
|
| D | cy8cproto_062_4343w.dts | 83 /* SDIO pins */
|
| /Zephyr-latest/drivers/disk/ |
| D | Kconfig.sdmmc | 63 Use eMMC instead of SDIO (SD card) protocol. These are similar, but not entirely the same.
|
| /Zephyr-latest/modules/hal_ambiq/ |
| D | Kconfig.hal | 97 Use the SDIO driver from Ambiq HAL
|
| /Zephyr-latest/modules/hal_infineon/ |
| D | Kconfig | 35 Enable Secure Digital Input/Output interface (SDIO) HAL module for Infineon devices
|
| /Zephyr-latest/drivers/wifi/infineon/ |
| D | Kconfig.airoc | 28 Enable SDIO bus support.
138 (E-Type Key w/ SDIO/UART)
|
| /Zephyr-latest/boards/google/dragonclaw/ |
| D | google_dragonclaw.dts | 39 div-q = <8>; /* 48MHz PLL output for USB, SDIO, RNG */
|
| /Zephyr-latest/boards/phytec/phyboard_nash/doc/ |
| D | index.rst | 32 - MMX/SD/SDIO: microSD slot
36 - Expansion Bus: I2C, SPI, SDIO, UART, USB
|
| /Zephyr-latest/boards/st/stm32f469i_disco/doc/ |
| D | index.rst | 58 - SDIO
91 - SDIO D0/D1/D2/D3/CLK/Detect : PC8/PC9/PC10/PC11/PC12/PG2
|
| /Zephyr-latest/drivers/wifi/nxp/ |
| D | Kconfig.nxp | 591 menu "Wi-Fi SDIO Multi Port Aggregation"
594 bool "SDIO Multiport Rx Aggregation"
597 This option enables SDIO Multiport Rx Aggregation support in the Wi-Fi driver.
600 bool "SDIO Multiport Tx Aggregation"
604 This option enables SDIO Multiport Rx Aggregation support in the Wi-Fi driver.
1169 SDIO bus.
1178 the SDIO bus.
1210 bool "SDIO debug"
1213 Enable this to monitor SDIO init deinit errors
1216 bool "SDIO IO debug"
[all …]
|
| /Zephyr-latest/boards/adafruit/feather_stm32f405/doc/ |
| D | index.rst | 19 - SD socket on the bottom, connected to SDIO port
|
| /Zephyr-latest/boards/espressif/esp32_devkitc_wroom/doc/ |
| D | index.rst | 29 - SD/SDIO/MMC host
30 - Slave (SDIO/SPI)
|
| /Zephyr-latest/boards/espressif/esp32_devkitc_wrover/doc/ |
| D | index.rst | 29 - SD/SDIO/MMC host
30 - Slave (SDIO/SPI)
|
| /Zephyr-latest/boards/others/stm32f401_mini/doc/ |
| D | index.rst | 29 - SDIO
|
| /Zephyr-latest/boards/nxp/imx91_evk/doc/ |
| D | index.rst | 25 - Murata Type-2EL (SDIO+UART+SPI) module. It is based on NXP IW612 SoC,
|
| /Zephyr-latest/boards/vcc-gnd/yd_esp32/doc/ |
| D | index.rst | 35 - SD/SDIO/MMC host
36 - Slave (SDIO/SPI)
|
| /Zephyr-latest/boards/phytec/phyboard_pollux/doc/ |
| D | index.rst | 33 - MMX/SD/SDIO: microSD slot
37 - Expansion Bus: I2C, SPI, SDIO, UART, USB
|
| /Zephyr-latest/boards/adi/max32650evkit/doc/ |
| D | index.rst | 38 - 240Mbps SDHC/eMMC/SDIO/microSD Interface
|
| /Zephyr-latest/boards/adi/max32650fthr/doc/ |
| D | index.rst | 38 - 240Mbps SDHC/eMMC/SDIO/microSD Interface
|
| /Zephyr-latest/boards/adi/ad_swiot1l_sl/doc/ |
| D | index.rst | 37 - 240Mbps SDHC/eMMC/SDIO/microSD Interface
|
| /Zephyr-latest/boards/atmel/sam0/same54_xpro/doc/ |
| D | index.rst | 34 - SD/SDIO card connector
|
| /Zephyr-latest/boards/weact/blackpill_f401cc/doc/ |
| D | index.rst | 31 - SDIO
|
1234
