Searched full:pads (Results 1 – 25 of 48) sorted by relevance
12
| /Zephyr-latest/dts/bindings/pinctrl/ |
| D | nxp,s32ze-pinctrl.yaml | 60 - termination resistor disabled (affect LVDS pads only).
61 - current reference control disabled (affect LVDS pads only).
62 - Rx current boost disabled (affect LVDS pads only).
101 - For 3.3 V / 1.8 V FAST pads:
107 - For 1.8 V GPIO pads:
113 - For 3.3 V GPIO pads:
124 the associated pin. It is only applicable to LVDS pads and
125 has no effect on other types of pads
131 the associated pin. It is only applicable to LVDS pads and
132 has no effect on other types of pads
[all …]
|
| D | nxp,imx7d-pinctrl.yaml | 90 SOC pads.
|
| D | nuvoton,npcx-pinctrl.yaml | 76 A map to DEVALTn that configures detection polarity of PSL input pads.
|
| D | ambiq,apollo3-pinctrl.yaml | 97 The 1.5K-24K pullup values are valid for select I2C enabled pads.
|
| /Zephyr-latest/dts/bindings/dac/ |
| D | espressif,esp32-dac.yaml | 10 Two GPIO pads can only be connected to the DAC peripheral.
12 ESP32 pads
16 ESP32-S2 pads
40 NOTE: The DAC peripheral outputs are fixed to gpio pads, therefore
|
| /Zephyr-latest/drivers/memc/ |
| D | memc_nxp_s32_qspi.h | 16 * @param pads pad information
19 #define QSPI_LUT_OP(inst, pads, op) \ argument
21 | (Qspi_Ip_InstrOpType)(pads) \
|
| /Zephyr-latest/dts/bindings/i2c/ |
| D | nuvoton,npcx-i2c-port.yaml | 4 description: Nuvoton, NPCX-I2C port pads node
19 description: i2c controller to handle signals from port pads
|
| /Zephyr-latest/soc/nuvoton/npcx/common/ |
| D | soc_gpio.h | 30 * @brief Enable the connection between io pads and GPIO instance
38 * @brief Disable the connection between io pads and GPIO instance
|
| D | soc_pins.h | 43 * @brief Select i2c port pads of i2c controller
46 * @param port index for i2c port pads
|
| D | power.c | 156 * Disable the connection between io pads that have leakage current and in npcx_power_enter_system_sleep()
192 * Restore the connection between io pads that have leakage current and in npcx_power_enter_system_sleep()
|
| /Zephyr-latest/boards/silabs/radio_boards/ |
| D | index.rst | 48 - Breakout pads for Wireless SoC I/O
60 - Breakout pads for Wireless SoC I/O
|
| /Zephyr-latest/dts/bindings/misc/ |
| D | nxp,s32-lcu.yaml | 7 signals, and Input/Output (I/O) pads, and combines them
|
| /Zephyr-latest/dts/bindings/ps2/ |
| D | nuvoton,npcx-ps2-channel.yaml | 4 description: Nuvoton, NPCX-PS/2 channel pads node
|
| /Zephyr-latest/dts/bindings/input/ |
| D | nuvoton,npcx-kbd.yaml | 29 For example the WUI mapping on 8 KSI pads would be
|
| /Zephyr-latest/drivers/pinctrl/ |
| D | pinctrl_npcx.c | 122 /* Configure peripheral device's drive mode. (Only PWM pads support it) */ in npcx_periph_configure()
134 /* Configure detection polarity of PSL input pads */ in npcx_psl_input_detection_configure()
141 /* Configure detection mode of PSL input pads */ in npcx_psl_input_detection_configure()
|
| /Zephyr-latest/modules/hal_rpi_pico/bootloader/ |
| D | CMakeLists.txt | 63 # Checksums the binary, pads it, and generates an assembly file
|
| /Zephyr-latest/dts/bindings/interrupt-controller/ |
| D | nxp,s32-siul2-eirq.yaml | 44 pads to filter out glitches on the inputs. The digital filter will be
|
| /Zephyr-latest/boards/quicklogic/qomu/doc/ |
| D | index.rst | 40 #. While the blue LED is blinking (for 5 seconds), touch the touch-pads with your finger.
|
| /Zephyr-latest/boards/brcm/bcm958401m2/doc/ |
| D | index.rst | 52 The bcm958401m2 board includes pads for soldering a JTAG connector.
|
| /Zephyr-latest/boards/brcm/bcm958402m2/doc/ |
| D | a72.rst | 48 The ``bcm958402m2/bcm58402/a72`` board includes pads for soldering a JTAG connector.
|
| D | m7.rst | 48 The ``bcm958402m2/bcm58402/m7`` board includes pads for soldering a JTAG connector.
|
| /Zephyr-latest/boards/shields/adafruit_neopixel_grid_bff/doc/ |
| D | index.rst | 55 Adafruit does provide solder pads for your own power supply on the
|
| /Zephyr-latest/drivers/spi/ |
| D | spi_sam0.c | 28 uint32_t pads; member
109 ctrla.reg |= cfg->pads; in spi_sam0_configure()
727 .pads = SPI_SAM0_SERCOM_PADS(n), \
737 .pads = SPI_SAM0_SERCOM_PADS(n), \
|
| /Zephyr-latest/boards/seeed/seeeduino_xiao/doc/ |
| D | index.rst | 108 entered by shorting the RST and GND pads twice.
145 #. Short the RST and GND pads twice quickly to enter bootloader mode
|
| /Zephyr-latest/boards/sparkfun/pro_micro_rp2040/doc/ |
| D | index.rst | 118 The Pro Micro board does make the SWD pins available on pads on the
|
12
