Searched full:bsp (Results 1 – 25 of 53) sorted by relevance
123
15 - clock-module-index # Same as u32ModuleIdx on invoking BSP CLK driver CLK_SetModuleClock()16 - clock-source # Same as u32ClkSrc on invoking BSP CLK driver CLK_SetModuleClock()17 - clock-divider # Same as u32ClkDiv on invoking BSP CLK driver CLK_SetModuleClock()
28 * clk_modidx is same as u32ModuleIdx in BSP CLK_SetModuleClock().29 * clk_src is same as u32ClkSrc in BSP CLK_SetModuleClock().30 * clk_div is same as u32ClkDiv in BSP CLK_SetModuleClock().
27 * BSP-Linux standard output. Can cause problems if used with standard bsp
111 …https://download.phytec.de/Software/Linux/BSP-Yocto-AM62x/BSP-Yocto-Ampliphy-AM62x-PD23.2.1/images…114 …https://download.phytec.de/Software/Linux/BSP-Yocto-AM62x/BSP-Yocto-Ampliphy-AM62x-PD23.2.1/images…
157 …https://download.phytec.de/Software/Linux/BSP-Yocto-AM62x/BSP-Yocto-Ampliphy-AM62x-PD23.2.1/images…160 …https://download.phytec.de/Software/Linux/BSP-Yocto-AM62x/BSP-Yocto-Ampliphy-AM62x-PD23.2.1/images…163 …https://docs.phytec.com/projects/yocto-phycore-am62x/en/bsp-yocto-ampliphy-am62x-pd23.2.1/bootinge…
139 …https://download.phytec.de/Software/Linux/BSP-Yocto-AM64x/BSP-Yocto-Ampliphy-AM64x-PD23.2.1/images…142 …https://download.phytec.de/Software/Linux/BSP-Yocto-AM64x/BSP-Yocto-Ampliphy-AM64x-PD23.2.1/images…145 …https://docs.phytec.com/projects/yocto-phycore-am64x/en/bsp-yocto-ampliphy-am64x-pd23.2.1/bootinge…
10 /* Beginning of M2L31 BSP sys_reg.h reset module copy */77 /* End of M2L31 BSP sys_reg.h reset module copy */79 /* Beginning of M2L31 BSP sys.h reset module copy */153 /* End of M2L31 BSP sys.h reset module copy */
10 /* Beginning of M460 BSP sys_reg.h reset module copy */176 /* End of M460 BSP sys_reg.h reset module copy */178 /* Beginning of M460 BSP sys.h reset module copy */269 /* End of M460 BSP sys.h reset module copy */
25 * Called in early BSP boot to set up scheduler IPI handling.
94 modify one of the examples in the [SparkFun Edge BSP](https://github.com/sparkfun/SparkFun_Edge_BSP)97 ### Install the Ambiq SDK and SparkFun Edge BSP101 guide to set up the Ambiq SDK and SparkFun Edge BSP.
168 remoteproc. Please check the `phyCORE-i.MX93 BSP Manual`_ for more information.177 .. _phyCORE-i.MX93 BSP Manual:178 https://phytec.github.io/doc-bsp-yocto/bsp/imx9/imx93/imx93.html
11 #include <bsp/include/nm_bsp.h>
21 #include <bsp/include/nm_bsp.h>
115 this BSP. SERCOM3 is the default Zephyr console.131 The SAML21 MCU has 6 SERCOM based SPIs, with two configured as SPI in this BSP.
244 `phyCORE-i.MX 8M Plus BSP Manual`_ for more information.250 - `phyCORE-i.MX 8M Plus BSP Manual`_261 .. _phyCORE-i.MX 8M Plus BSP Manual:262 https://phytec.github.io/doc-bsp-yocto/bsp/imx8/imx8mp/imx8mp.html
131 this BSP. SERCOM0 is the default Zephyr console.145 The SAMR34 MCU has 6 SERCOM based SPIs, with two configured as SPI in this BSP.
195 This can be done with U-Boot or Phytec's Linux BSP via remoteproc.197 Because remoteproc in Phytec's BSP only writes to the TCM memory area,200 You can read more about remoteproc in Phytec's BSP here: `Remoteproc BSP`_281 will be included in a future BSP release.397 .. _Remoteproc BSP:
56 * BSP controls alt_load() behavior in crt0.
152 The default is chosen by following BSP sample,
147 The BSP must provide a valid default for proper operation.157 The BSP must provide a valid default. This drives the size of the
13 such as Linux BSP and hypervisors.
116 this BSP. SERCOM4 is the default Zephyr console.
115 this BSP. SERCOM3 is the default Zephyr console.
85 uint8_t ep_hw_idx; /* BSP USBD driver EP index EP0, EP1, EP2, etc */86 uint32_t ep_hw_cfg; /* BSP USBD driver EP configuration */337 /* NOTE: BSP USBD driver: ATTR = 0x7D0 */ in numaker_usbd_hw_setup()674 /* BSP USBD driver EP handle */ in numaker_usbd_ep_mgmt_init()678 /* Reserve 1st/2nd EP H/W contexts (BSP USBD driver EP0/EP1) for CTRL OUT/IN */ in numaker_usbd_ep_mgmt_init()688 /* Reserve 1st EP H/W context (BSP USBD driver EP0) for CTRL OUT */ in numaker_usbd_ep_mgmt_init()699 /* Reserve 2nd EP H/W context (BSP USBD driver EP1) for CTRL IN */ in numaker_usbd_ep_mgmt_init()
