Searched refs:these (Results 276 – 300 of 642) sorted by relevance
1...<<11121314151617181920>>...26
| /Zephyr-latest/samples/net/prometheus/ |
| D | README.rst | 63 To customize these options, we can run ``west build -t menuconfig``, which provides
|
| /Zephyr-latest/tests/drivers/build_all/sensor/ |
| D | app.overlay | 9 * with real-world devicetree nodes, to allow these tests to run on
|
| /Zephyr-latest/samples/basic/blinky/ |
| D | README.rst | 28 #. Have an LED connected via a GPIO pin (these are called "User LEDs" on many of
|
| /Zephyr-latest/samples/boards/phytec/reel_board/mesh_badge/ |
| D | README.rst | 16 however these instructions focus on the necessary steps for phones.
|
| /Zephyr-latest/boards/nxp/mimxrt595_evk/doc/ |
| D | index.rst | 41 these references:
206 if not already done (these jumpers are installed by default).
216 and J19 (these are installed by default).
|
| /Zephyr-latest/boards/nxp/mimxrt685_evk/doc/ |
| D | index.rst | 38 these references:
241 if not already done (these jumpers are installed by default).
256 and J19 (these are installed by default).
|
| /Zephyr-latest/boards/element14/warp7/doc/ |
| D | index.rst | 58 For more information about the i.MX7 SoC and WaRP7, see these references:
117 The A7 can perform these steps at bootloader level or after the Linux system
267 With these mechanisms, applications for the ``warp7`` board
|
| /Zephyr-latest/boards/weact/mini_stm32h743/doc/ |
| D | index.rst | 122 To activate the bootloader, follow these steps:
128 Upon successful execution of these steps, the device will transition into
|
| /Zephyr-latest/subsys/testsuite/ |
| D | Kconfig | 187 the testing suite to utilize these exceptions, in tests.
189 set, these exceptions are set to target the Non-Secure state.
|
| /Zephyr-latest/drivers/wifi/esp32/ |
| D | Kconfig.esp32 | 90 WiFi hardware use these buffers to receive all 802.11 frames.
109 application can process them. In these cases we may run out of memory if
158 In these cases, we may run out of TX buffers.
187 than WiFi layer can transmit. In these cases, we may run out of TX
|
| /Zephyr-latest/doc/security/ |
| D | secure-coding.rst | 18 should comply with these principles.
102 In addition to these general principles, the following points are
231 enforcing this guideline, monitoring reviews, and improving these
245 secure designer to also review the code. Any of these individuals
|
| /Zephyr-latest/arch/xtensa/core/ |
| D | README_MMU.txt | 15 "special" ways storing mappings under OS control. Some of these are
119 one of these to "pin" the top-level page table entry in place,
153 uncached. So at boot the CPU relies on these TLB entries to provide a
196 reasonable hardware these regions will be near each other)
202 these would be used by the kernel for all physical memory and that the
|
| /Zephyr-latest/boards/espressif/esp_wrover_kit/doc/ |
| D | index.rst | 88 | | these pairs of pins are connected with jumpers. To use ESP32’s serial |
93 | | memory inside the module. Use these pins to connect ESP32 to |
102 | | the inward and outward sides of JP2 respectively. By default, these |
190 that hardware is not used, e.g., nothing is plugged into the Camera (JP4) header, then these
297 improving the integrity of bus signals, you can desolder these resistors to disconnect the
|
| /Zephyr-latest/boards/shields/mikroe_ble_tiny_click/doc/ |
| D | index.rst | 36 as these signals are not supported on the Click footprint.
|
| /Zephyr-latest/boards/silabs/dev_kits/xg24_ek2703a/doc/ |
| D | index.rst | 21 For more information about the EFR32MG24 SoC and BRD2703A board, refer to these
|
| /Zephyr-latest/scripts/net/ |
| D | run-sample-tests.sh | 306 run the tests in these directories instead of current directory
|
| /Zephyr-latest/boards/silabs/radio_boards/siwx917_rb4338a/doc/ |
| D | index.rst | 22 For more information about the SiWG917 SoC and BRD4338A board, refer to these
|
| /Zephyr-latest/boards/silabs/radio_boards/slwrb4180a/doc/ |
| D | index.rst | 25 For more information about the EFR32MG21 SoC and BRD4180A board, refer to these
|
| /Zephyr-latest/boards/silabs/radio_boards/slwrb4255a/doc/ |
| D | index.rst | 24 For more information about the EFR32FG13 SoC and BRD4255A board, refer to these
|
| /Zephyr-latest/doc/hardware/peripherals/sensor/ |
| D | fetch_and_get.rst | 25 internally provide exclusive access to the device during or between these
|
| /Zephyr-latest/doc/develop/toolchains/ |
| D | custom_cmake.rst | 6 To use a custom toolchain defined in an external CMake file, :ref:`set these
|
| /Zephyr-latest/samples/net/sockets/echo_server/ |
| D | Kconfig | 109 # device stack. The scope of these options is limited to USB samples in project
|
| /Zephyr-latest/samples/boards/st/power_mgmt/serial_wakeup/ |
| D | README.rst | 87 With all these conditions matched, one can reach 10uA on stm32l562e_dk with this sample.
|
| /Zephyr-latest/doc/hardware/peripherals/ |
| D | mspi.rst | 8 address and data phases, and multiple signal lines during these phases.
29 and implement the MSPI APIs, and device drivers that reference these APIs.
|
| /Zephyr-latest/boards/ti/cc1352r_sensortag/doc/ |
| D | index.rst | 122 Follow these `xds110 firmware update directions
130 You can obtain OpenOCD by following these
|
1...<<11121314151617181920>>...26
