Searched refs:than (Results 151 – 175 of 493) sorted by relevance
12345678910>>...20
| /Zephyr-latest/doc/hardware/arch/ |
| D | semihost.rst | 24 of code across datasets that are larger than what can fit into ROM of an
|
| /Zephyr-latest/drivers/modem/ |
| D | Kconfig.hl7800 | 299 Note that the priority needs to be lower than the net stack
359 This value should be set larger than the network latency. Otherwise
372 CTS pulses shorter than this value will be ignored.
|
| /Zephyr-latest/modules/openthread/ |
| D | Kconfig.features | 100 mbedTLS heap than the default value. A minimum recommended value of
114 Use host time rather than radio platform time to track elapsed time
206 mbedTLS heap than the default value. A minimum recommended value of
|
| /Zephyr-latest/drivers/virtualization/ |
| D | Kconfig | 41 more or less than necessary. Depends on how many VMs will connect
|
| /Zephyr-latest/boards/raspberrypi/rpi_pico2/ |
| D | rpi_pico2.dtsi | 71 * smaller than 256 bytes, but in practice the linker places the vector
|
| /Zephyr-latest/subsys/demand_paging/eviction/ |
| D | Kconfig | 39 the page eviction queue. This is more efficient than the NRU
|
| /Zephyr-latest/drivers/gpio/ |
| D | gpio_sn74hc595.c | 25 #error SPI_INIT_PRIORITY must be lower than SN74HC595_INIT_PRIORITY
|
| /Zephyr-latest/drivers/interrupt_controller/ |
| D | Kconfig.loapic | 21 priority to be greater than or equal to the level of the
|
| /Zephyr-latest/subsys/net/l2/ieee802154/ |
| D | Kconfig.radio | 65 than or equal NET_L2_IEEE802154_RADIO_CSMA_CA_MAX_BE.
|
| /Zephyr-latest/boards/mediatek/mt8196/ |
| D | mt8196_adsp.dts | 42 * than the driver here supports. There are 64 total
|
| /Zephyr-latest/doc/develop/sca/ |
| D | gcc.rst | 8 analysis of the code than traditional warnings.
|
| /Zephyr-latest/boards/adafruit/qt_py_esp32s3/ |
| D | adafruit_qt_py_esp32s3_procpu.dts | 129 * its positive side hooked up to a GPIO pin rather than a positive voltage
|
| /Zephyr-latest/drivers/adc/ |
| D | Kconfig.mcux | 120 The user can reduce this value if their application uses fewer than
|
| /Zephyr-latest/doc/hardware/peripherals/ |
| D | uart.rst | 29 than the other methods.
|
| /Zephyr-latest/samples/shields/x_nucleo_53l0a1/ |
| D | README.rst | 19 the center sensor (soldered on the shield) is lower than 1.25m, then the
|
| /Zephyr-latest/boards/adafruit/feather_m4_express/doc/ |
| D | index.rst | 30 :code:`CONFIG_SYS_CLOCK_TICKS_PER_SEC` to no more than 32 kHZ divided by 7,
31 i.e. no more than 4500.
|
| /Zephyr-latest/drivers/clock_control/ |
| D | Kconfig.nrf | 100 was less than configured threshold. If number of consecutive skips
230 Must be higher than NRFS backend
|
| /Zephyr-latest/doc/services/rtio/ |
| D | index.rst | 33 to do rather than direct operations through C and callbacks is needed. Enabling
35 more than a simple list of descriptions.
209 descriptors entirely. Meaning the hardware can potentially do more than ever.
213 threads per peripheral. RTIO is much lower cost than that.
|
| /Zephyr-latest/doc/security/ |
| D | secure-coding.rst | 93 than one user or process shall not be shared if not strictly
161 depend on more than one condition, so that defeating one protection
164 token, is stronger than single-factor authentication)
170 common to more than one user and depended on by all users, e.g.,
193 initiated the project (and have not left the project more than three
|
| /Zephyr-latest/subsys/net/lib/sockets/ |
| D | Kconfig | 50 maximum timeout is 5 min. If the value is higher than
61 smaller than this value, then this value is ignored. If the timeout
131 Processing priority for TLS sockets. Should be lower than
261 If native TLS is enabled, lower value than NET_SOCKETS_TLS_PRIORITY
263 socket implementation). Higher value than NET_SOCKETS_TLS_PRIORITY
|
| /Zephyr-latest/soc/microchip/mec/mec15xx/ |
| D | Kconfig | 94 # higher than that.
|
| /Zephyr-latest/drivers/sensor/st/lsm6dsv16x/ |
| D | Kconfig | 90 a maximum of two external sensors (if more than two are enabled
|
| /Zephyr-latest/boards/shields/frdm_kw41z/doc/ |
| D | index.rst | 52 routes the UART RX and TX signals to the Arduino header, rather than to the
|
| /Zephyr-latest/drivers/flash/ |
| D | Kconfig.nordic_qspi_nor | 42 if the data is larger than the configured size.
|
| D | Kconfig.simulator | 43 bool "Allow program units to be programmed more than once"
|
12345678910>>...20
