Searched refs:speed (Results 1351 – 1375 of 1639) sorted by relevance
1...<<51525354555657585960>>...66
| /Zephyr-latest/boards/st/nucleo_l433rc_p/doc/ |
| D | index.rst | 69 - USB 2.0 full-speed crystal less solution with LPM and BCD
157 driven by 16MHz high speed internal oscillator.
|
| /Zephyr-latest/boards/st/stm32f429i_disc1/doc/ |
| D | index.rst | 57 - USB 2.0 OTG HS/FS with dedicated DMA, on-chip full-speed PHY and ULPI
138 driven by an 8MHz high speed external clock.
|
| /Zephyr-latest/boards/others/neorv32/doc/ |
| D | index.rst | 88 ``current-speed`` property of the ``uart0`` devicetree node.
144 …d="--config;interface/ftdi/flyswatter.cfg;--config;neorv32.cfg;--cmd-pre-init;'adapter speed 2000'"
|
| /Zephyr-latest/dts/arm/st/l4/ |
| D | stm32l4p5.dtsi | 311 maximum-speed = "full-speed";
|
| /Zephyr-latest/dts/arm/renesas/smartbond/ |
| D | da1469x.dtsi | 382 maximum-speed = "full-speed";
|
| /Zephyr-latest/drivers/wifi/esp32/ |
| D | Kconfig.esp32 | 226 speed. Helpful when the device is operating in crowded wireless area.
246 speed. Helpful when the device is operating in crowded wireless area.
278 bool "WiFi IRAM speed optimization"
287 bool "WiFi RX IRAM speed optimization"
|
| /Zephyr-latest/tests/bsim/bluetooth/audio/src/ |
| D | mcc_test.c | 178 int8_t speed) in mcc_read_playback_speed_cb() argument
185 g_pb_speed = speed; in mcc_read_playback_speed_cb()
189 static void mcc_set_playback_speed_cb(struct bt_conn *conn, int err, int8_t speed) in mcc_set_playback_speed_cb() argument
196 g_pb_speed = speed; in mcc_set_playback_speed_cb()
201 int8_t speed) in mcc_read_seeking_speed_cb() argument
|
| /Zephyr-latest/boards/native/doc/ |
| D | arch_soc.rst | 123 - Code that depends on its own execution speed will normally not
246 The problem of how to emulate the instruction execution speed is solved
271 QEMU cannot provide any emulation of execution speed. It simply
272 executes code as fast as it can, and lets the host CPU speed determine the
273 emulated CPU speed. This produces highly indeterministic behavior,
274 as the execution speed depends on the host system performance and its load.
|
| /Zephyr-latest/subsys/mgmt/mcumgr/transport/ |
| D | Kconfig.bluetooth | 53 SMP commands are handled. This option allows to speed up the command
|
| /Zephyr-latest/samples/boards/st/power_mgmt/serial_wakeup/ |
| D | README.rst | 28 - If LSE is selected as clock source and shell serial port is a LPUART current speed
|
| /Zephyr-latest/boards/seagate/legend/ |
| D | legend.dts | 51 current-speed = <115200>;
|
| /Zephyr-latest/boards/u-blox/ubx_bmd380eval/ |
| D | ubx_bmd380eval_nrf52840.dts | 121 current-speed = <115200>;
|
| /Zephyr-latest/boards/panasonic/pan1782_evb/ |
| D | pan1782_evb.dts | 124 current-speed = <115200>;
|
| /Zephyr-latest/boards/st/nucleo_h753zi/ |
| D | nucleo_h753zi.dts | 113 current-speed = <115200>;
|
| /Zephyr-latest/boards/st/nucleo_wl55jc/ |
| D | nucleo_wl55jc.dts | 114 current-speed = <115200>;
|
| /Zephyr-latest/boards/panasonic/pan1783/ |
| D | pan1783_nrf5340_cpunet_common.dtsi | 149 current-speed = <115200>;
|
| /Zephyr-latest/boards/andestech/adp_xc7k_ae350/ |
| D | adp_xc7k_ae350.dts | 156 current-speed = <115200>;
|
| /Zephyr-latest/boards/m5stack/m5stickc_plus/ |
| D | m5stickc_plus_procpu.dts | 106 current-speed = <115200>;
|
| /Zephyr-latest/boards/bbc/microbit/ |
| D | bbc_microbit.dts | 121 current-speed = <115200>;
|
| /Zephyr-latest/boards/nxp/frdm_k22f/ |
| D | frdm_k22f.dts | 165 current-speed = <115200>;
|
| /Zephyr-latest/drivers/spi/ |
| D | spi_mchp_mss_qspi.c | 350 uint32_t idx, clkrate, val = 0, speed; in mss_qspi_clk_gen_set() local
353 speed = s->clock_freq / 2; in mss_qspi_clk_gen_set()
|
| /Zephyr-latest/dts/arm/atmel/ |
| D | same70.dtsi | 321 maximum-speed = "high-speed";
|
| /Zephyr-latest/soc/cdns/dc233c/include/ |
| D | xtensa-dc233c.ld | 136 * code here to avoid TLB misses, thus speed up exception
167 /* Below are to speed up execution by avoiding TLB misses
|
| /Zephyr-latest/boards/seeed/lora_e5_mini/doc/ |
| D | index.rst | 129 High-speed internal (HSI) or High-speed external (HSE) oscillator, as well as
|
| /Zephyr-latest/boards/u-blox/ubx_evkninab3/doc/ |
| D | index.rst | 295 current-speed = <115200>;
318 can only be used in under-10KHz applications. They are not suitable for 115200 speed of UART.
|
1...<<51525354555657585960>>...66
