Searched full:rs485 (Results 1 – 25 of 26) sorted by relevance
12
| /Zephyr-latest/dts/bindings/serial/ |
| D | nxp,lpuart.yaml | 26 nxp,rs485-mode:
33 nxp,rs485-de-active-low:
35 description: RTS polarity at RS485 mode.
|
| D | espressif,esp32-uart.yaml | 17 hw-rs485-hd-mode:
20 Enable the hardware RS485 half duplex mode.
|
| /Zephyr-latest/doc/services/modbus/ |
| D | index.rst | 9 with different physical interfaces, like RS485 or RS232.
|
| /Zephyr-latest/samples/subsys/modbus/rtu_client/ |
| D | README.rst | 61 .. _`joy-it RS-485 shield for Arduino`: https://joy-it.net/en/products/ARD-RS485
|
| /Zephyr-latest/boards/kincony/kincony_kc868_a32/doc/ |
| D | index.rst | 15 - RS485 interface
|
| /Zephyr-latest/boards/phytec/phyboard_polis/ |
| D | phyboard_polis_mimx8mm6_m4.dts | 81 /* RS232 / RS485 pinheader on the board */
|
| /Zephyr-latest/boards/st/stm32g081b_eval/doc/ |
| D | index.rst | 14 with USB PD, motor control connector, RS232, RS485, Audio DAC, microphone ADC,
47 - RS-232 and RS485 communications
|
| /Zephyr-latest/samples/subsys/modbus/rtu_server/ |
| D | README.rst | 152 .. _`joy-it RS-485 shield for Arduino`: https://joy-it.net/en/products/ARD-RS485
|
| /Zephyr-latest/boards/arduino/opta/ |
| D | arduino_opta-common.dtsi | 99 /* The RS485 is often used with the ModBus protocol. */
|
| /Zephyr-latest/boards/renesas/rzt2m_starterkit/doc/ |
| D | index.rst | 39 * RS485,
|
| /Zephyr-latest/boards/firefly/roc_rk3568_pc/doc/ |
| D | index.rst | 9 Control Port can be connected with RS485/RS232 devices.
|
| /Zephyr-latest/boards/witte/linum/doc/ |
| D | index.rst | 8 of communications interfaces like UART with RS232 and RS485 capabillities, CAN bus compatible to
30 - 2 On-board RS485 Transceiver
|
| /Zephyr-latest/boards/st/stm32f072_eval/doc/ |
| D | index.rst | 15 - RS232 and RS485 communication
|
| /Zephyr-latest/boards/phytec/phyboard_polis/doc/ |
| D | index.rst | 43 - 1x RS232 / RS485
120 | RS232/485 | UART1 | RS232 / RS485 with flow-control |
|
| /Zephyr-latest/boards/seco/stm32f3_seco_d23/doc/ |
| D | index.rst | 36 - RS485
|
| /Zephyr-latest/boards/st/nucleo_f446re/doc/ |
| D | index.rst | 155 used with `RS485 CAN Shield`_.
|
| /Zephyr-latest/boards/phytec/phyboard_nash/doc/ |
| D | index.rst | 29 - Serial: 1x RS232 / RS485 Full Duplex / Half Duplex
|
| /Zephyr-latest/boards/arduino/opta/doc/ |
| D | index.rst | 70 | RS485 | on-board | uart |
|
| /Zephyr-latest/boards/phytec/phyboard_pollux/doc/ |
| D | index.rst | 29 - Serial: 1x RS232 / RS485 Full Duplex / Half Duplex
|
| /Zephyr-latest/boards/st/steval_stwinbx1/doc/ |
| D | index.rst | 20 sensor data through either the built-in RS485 transceiver, BLE, Wi-Fi, and
|
| /Zephyr-latest/include/zephyr/drivers/ |
| D | uart.h | 114 UART_CFG_FLOW_CTRL_RS485, /**< RS485 flow control */
|
| /Zephyr-latest/drivers/serial/ |
| D | uart_mcux_lpuart.c | 1107 /* Set the LPUART into RS485 mode (tx driver enable using RTS) */ in mcux_lpuart_configure_init()
|
| D | uart_stm32.c | 575 /* Driver supports only RTS/CTS and RS485 flow control */ in uart_stm32_configure()
|
| /Zephyr-latest/doc/releases/ |
| D | release-notes-3.5.rst | 735 * Added RS485 support.
|
| D | release-notes-3.3.rst | 1698 - new property: ``nxp,rs485-mode``
1699 - new property: ``nxp,rs485-de-active-low``
|
12
