Home
last modified time | relevance | path

Searched refs:dout (Results 1 – 9 of 9) sorted by relevance

/Zephyr-latest/drivers/gpio/
Dgpio_xlnx_axi.c53 uint32_t dout; member
124 data->dout |= BIT(pin); in gpio_xlnx_axi_pin_configure()
126 data->dout &= ~BIT(pin); in gpio_xlnx_axi_pin_configure()
134 gpio_xlnx_axi_write_data(dev, data->dout); in gpio_xlnx_axi_pin_configure()
155 data->dout = (data->dout & ~mask) | (mask & value); in gpio_xlnx_axi_port_set_masked_raw()
156 gpio_xlnx_axi_write_data(dev, data->dout); in gpio_xlnx_axi_port_set_masked_raw()
168 data->dout |= pins; in gpio_xlnx_axi_port_set_bits_raw()
169 gpio_xlnx_axi_write_data(dev, data->dout); in gpio_xlnx_axi_port_set_bits_raw()
181 data->dout &= ~pins; in gpio_xlnx_axi_port_clear_bits_raw()
182 gpio_xlnx_axi_write_data(dev, data->dout); in gpio_xlnx_axi_port_clear_bits_raw()
[all …]
/Zephyr-latest/drivers/dp/
Dswdp_bitbang.c43 struct gpio_dt_spec dout; member
117 if (config->dout.port) { in pin_swdio_set()
119 swdp_ll_pin_set(config->dout_reg, config->dout.pin); in pin_swdio_set()
121 gpio_pin_set_dt(&config->dout, 1); in pin_swdio_set()
137 if (config->dout.port) { in pin_swdio_clr()
139 swdp_ll_pin_clr(config->dout_reg, config->dout.pin); in pin_swdio_clr()
141 gpio_pin_set_dt(&config->dout, 0); in pin_swdio_clr()
477 gpio_pin_set_dt(&config->dout, 1); in sw_set_pins()
479 gpio_pin_set_dt(&config->dout, 0); in sw_set_pins()
580 if (config->dout.port) { in sw_port_on()
[all …]
/Zephyr-latest/samples/subsys/dap/boards/
Dnrf52840dk_nrf52840.overlay13 dout-gpios = <&arduino_header 9 GPIO_ACTIVE_HIGH>; /* D3 */
/Zephyr-latest/boards/digilent/arty_a7/dts/
Darty_a7_arm_designstart.dtsi165 xlnx,dout-default = <0x0>;
212 xlnx,dout-default = <0x0>;
213 xlnx,dout-default-2 = <0x0>;
238 xlnx,dout-default = <0x0>;
239 xlnx,dout-default-2 = <0x0>;
/Zephyr-latest/soc/silabs/common/
Dpinctrl_soc.h43 uint8_t dout; member
79 .dout = Z_PINCTRL_SILABS_DOUT_INIT(node)},
/Zephyr-latest/drivers/pinctrl/
Dpinctrl_silabs_dbus.c23 GPIO_PinModeSet(pins[i].port, pins[i].pin, pins[i].mode, pins[i].dout); in pinctrl_configure_pins()
/Zephyr-latest/soc/espressif/common/
DKconfig.esptool74 default "dout" if ESPTOOLPY_FLASHMODE_DOUT
77 # fasted (see ESPTOOL-274), using dout instead. In ROM the flash mode
78 # information get from efuse, so don't care this dout choice.
79 default "dout" if ESPTOOLPY_FLASHMODE_OPI
/Zephyr-latest/drivers/usb/udc/
Dudc_common.h353 struct net_buf *const dout);
Dudc_common.c895 struct net_buf *const dout) in udc_ctrl_submit_s_out_status() argument
897 struct udc_buf_info *bi = udc_get_buf_info(dout); in udc_ctrl_submit_s_out_status()
903 net_buf_frag_add(data->setup, dout); in udc_ctrl_submit_s_out_status()
905 buf = udc_ctrl_alloc_status(dev, dout, USB_CONTROL_EP_IN); in udc_ctrl_submit_s_out_status()