Searched full:detection (Results 1 – 25 of 284) sorted by relevance
12345678910>>...12
| /Zephyr-latest/drivers/sensor/adi/adxl367/ |
| D | Kconfig | 36 Threshold for activity detection.
43 Threshold for in-activity detection.
50 The activity timer implements a robust activity detection that
52 only sustained motion can trigger activity detection. Value is the
67 bool "Use activity detection"
70 Enable Activity detection.
73 bool "Use inactivity detection"
76 Enable Inactivity detection.
80 bool "Use referenced activity detection"
83 Activity detection can be configured as referenced or absolute.
[all …]
|
| /Zephyr-latest/drivers/sensor/nuvoton/nuvoton_adc_cmp_npcx/ |
| D | Kconfig | 9 bool "Nuvoton NPCX ADC threshold detection interruption"
19 bool "NPCX ADC threshold detection uses internal work queue"
21 Threshold detection ISR utilizes system work queue for calling
27 int "Nuvoton NPCX ADC trheshold detection work queue priority"
30 This option sets internal ADC NPCX threshold detection workqueue
34 int "Nuvoton NPCX ADC trheshold detection work queue stack size"
37 This option sets internal ADC NPCX threshold detection workqueue
|
| /Zephyr-latest/dts/bindings/pinctrl/ |
| D | nuvoton,npcx-pinctrl.yaml | 17 - psl-in-mode: Select the assertion detection mode of PSL input
18 - psl-in-pol: Select the assertion detection polarity of PSL input
71 Offset to PSL_CTS register that is used for PSL input's status and detection mode.
76 A map to DEVALTn that configures detection polarity of PSL input pads.
87 The assertion detection mode of PSL input selection
88 - "level": Select the detection mode to level detection
89 - "edge": Select the detection mode to edge detection
96 The assertion detection polarity of PSL input selection
97 - "low-falling": Select the detection polarity to low/falling
98 - "high-rising": Select the detection polarity to high/rising
|
| D | ti,cc13xx-cc26xx-pinctrl.yaml | 32 - ti,input-edge-detect: enable and configure edge detection interrupts
62 To configure an input pin with edge detection (e.g. to count pulses):
130 default: 0 # no edge detection
132 Enables or disables the edge detection interrupt and configures it:
133 IOC_NO_EDGE: No edge detection (SoC default)
134 IOC_FALLING_EDGE: Edge detection on falling edge
135 IOC_RISING_EDGE: Edge detection on rising edge
136 IOC_BOTH_EDGES: Edge detection on both edges
|
| /Zephyr-latest/drivers/sensor/ite/ite_vcmp_it8xxx2/ |
| D | Kconfig | 25 bool "ITE it8xxx2 voltage comparator threshold detection uses internal work queue"
27 Threshold detection ISR utilizes system work queue for calling
33 int "ITE it8xxx2 voltage comparator threshold detection work queue priority"
36 This option sets internal ITE voltage comparator threshold detection
40 int "ITE it8xxx2 voltage comparator threshold detection work queue stack size"
43 This option sets internal ITE voltage comparator threshold detection
|
| /Zephyr-latest/dts/bindings/gpio/ |
| D | zephyr,gpio-emul.yaml | 12 description: Enables support for rising edge interrupt detection
16 description: Enables support for falling edge interrupt detection
20 description: Enables support for high level interrupt detection
24 description: Enables support for low level interrupt detection
|
| D | adi,max14916-gpio.yaml | 150 Set threshold voltage for short-to-V DD detection
151 0: Set threshold voltage for short-to-VDD detection to 9V (typ)
152 1: Set threshold voltage for short-to-VDD detection to 10V (typ)
153 2: Set threshold voltage for short-to-VDD detection to 12V (typ)
154 3: Set threshold voltage for short-to-VDD detection to 14V (typ)
165 Set the pullup current for open-wire and short-to-VDD detection
166 0: Set open-wire and short-to-VDD detection current to 60μA (typ)
167 1: Set open-wire and short-to-VDD detection current to 100μA (typ)
168 2: Set open-wire and short-to-VDD detection current to 300μA (typ)
169 3: Set open-wire and short-to-VDD detection current to 600μA (typ)
|
| D | adi,max14906-gpio.yaml | 161 Set threshold voltage for short-to-V DD detection
162 0: Set threshold voltage for short-to-VDD detection to 9V (typ)
163 1: Set threshold voltage for short-to-VDD detection to 10V (typ)
164 2: Set threshold voltage for short-to-VDD detection to 12V (typ)
165 3: Set threshold voltage for short-to-VDD detection to 14V (typ)
176 Set the pullup current for open-wire and short-to-VDD detection
177 0: Set open-wire and short-to-VDD detection current to 60μA (typ)
178 1: Set open-wire and short-to-VDD detection current to 100μA (typ)
179 2: Set open-wire and short-to-VDD detection current to 300μA (typ)
180 3: Set open-wire and short-to-VDD detection current to 600μA (typ)
|
| /Zephyr-latest/soc/nuvoton/npcx/common/ |
| D | soc_pins.h | 35 * low-voltage detection.
64 * @brief Enable low-voltage input detection
66 * @param lvol_ctrl Related register index for low-voltage detection
67 * @param lvol_bit Related register bit for low-voltage detection
68 * @param enable True to enable low-voltage input detection, false to disable.
73 * @brief Get status of low-voltage input detection
75 * @param lvol_ctrl Related register index for low-voltage detection
76 * @param lvol_bit Related register bit for low-voltage detection
|
| /Zephyr-latest/drivers/sensor/st/lis2dw12/ |
| D | Kconfig | 62 bool "Tap and Tap-Tap detection"
64 Enable tap (single/double) detection
74 bool "Wakeup detection (via interrupt)"
76 Enable the wakeup detection feature.
85 bool "Free Fall detection (via interrupt)"
87 Enable freefall detection via interrupt.
|
| /Zephyr-latest/drivers/sensor/adi/adxl372/ |
| D | Kconfig | 44 Threshold for activity detection.
51 Threshold for in-activity detection.
58 The activity timer implements a robust activity detection that
60 only sustained motion can trigger activity detection.
77 bool "Use referenced activity/in-activity detection"
80 Activity detection can be configured as referenced or absolute.
81 When using absolute activity detection, acceleration samples are
84 activity detection to be based not on an absolute threshold,
|
| /Zephyr-latest/boards/shields/x_nucleo_53l0a1/doc/ |
| D | index.rst | 3 X-NUCLEO-53L0A1 ranging and gesture detection sensor expansion board
10 detection sensor, based on ST’s FlightSense™, Time-of-Flight technology. It is
12 detection capabilities of the VL53L0X module.
54 - `X-NUCLEO-53L0A1 ranging and gesture detection sensor expansion board User Manual`_
55 - `VL53L0X Time-of-Flight ranging and gesture detection sensor Datasheet`_
81 .. _X-NUCLEO-53L0A1 ranging and gesture detection sensor expansion board User Manual:
82 …om/resource/en/user_manual/dm00285104-xnucleo53l0a1-ranging-and-gesture-detection-sensor-expansion…
84 .. _VL53L0X Time-of-Flight ranging and gesture detection sensor Datasheet:
|
| /Zephyr-latest/drivers/sensor/nxp/fxos8700/ |
| D | Kconfig | 86 bool "Pulse detection"
88 Enable pulse detection
100 bool "Motion detection"
102 Enable motion detection
111 bool "Magnetic vector-magnitude detection"
113 Enable magnetic vector-magnitude detection
|
| /Zephyr-latest/dts/bindings/regulator/ |
| D | regulator.yaml | 160 passed to disable error detection and value '1' indicates that detection
169 detection and value '1' indicates that detection should be enabled but
185 passed to disable error detection and value '1' indicates that detection
195 detection and value '1' indicates that detection should be enabled but
213 passed to disable error detection and value '1' indicates that detection
223 disable detection and value '1' indicates that detection should be enabled
240 can be passed to disable error detection and value '1' indicates that
241 detection should be enabled but limit setting can be omitted.
249 disable detection and value '1' indicates that detection should be enabled
|
| D | raspberrypi,core-supply-regulator.yaml | 21 raspberrypi,brown-out-detection:
24 Enable brown-out detection
48 (determined by the 'brown-out detection assertion delay').
|
| /Zephyr-latest/drivers/sensor/st/iis2dlpc/ |
| D | Kconfig | 62 bool "Tap and Tap-Tap detection"
64 Enable tap (single/double) detection
67 bool "Activity detection"
69 Enable activity/inactivity detection
|
| /Zephyr-latest/soc/espressif/common/ |
| D | Kconfig.flash | 18 Enable this to support auto detection of ISSI chips if chip vendor not directly
26 Enable this to support auto detection of MXIC chips if chip vendor not directly
34 Enable this to support auto detection of GD (GigaDevice) chips if chip vendor not
47 Enable this to support auto detection of Winbond chips if chip vendor not directly
55 Enable this to support auto detection of BOYA chips if chip vendor not directly
63 Enable this to support auto detection of TH chips if chip vendor not directly
72 Enable this to support auto detection of Octal MXIC chips if chip vendor not directly
|
| /Zephyr-latest/doc/hardware/peripherals/ |
| D | bc12.rst | 7 referred to as just BC1.2. BC1.2 defines limits and detection mechanisms for USB
50 For the disconnected state, the BC1.2 driver powers down the detection chip.
60 For portable-device mode, the BC1.2 driver powers up the detection chip and
61 starts charger detection. At completion of the charger detection, the BC1.2
67 (Standard Downstream Port) charging partner or if BC1.2 detection fails, the
75 BC1.2 driver powers up the detection chip and configures the charger type
76 specified by a devicetree property. If the driver supports detection of plug and
|
| /Zephyr-latest/drivers/usb/bc12/ |
| D | Kconfig.pi3usb9201 | 13 client mode it starts BC1.2 detection to detect the attached host
14 type. It provides an I2C interface to report detection results.
33 CDP (Charging Downstream Port), after successful CDP detection the
|
| /Zephyr-latest/dts/bindings/sensor/ |
| D | nxp,fxos8700-common.yaml | 62 Threshold to start the pulse-event detection procedure on the X-axis.
72 Threshold to start the pulse-event detection procedure on the Y-axis.
82 Threshold to start the pulse-event detection procedure on the Z-axis.
104 The time interval that starts after the first pulse detection where the
105 pulse-detection function ignores the start of a new pulse. The
118 detection. The detected second pulse width must be shorter than the
|
| /Zephyr-latest/include/zephyr/dt-bindings/pinctrl/ |
| D | cc13xx_cc26xx-pinctrl.h | 60 /* Edge Detection */
61 #define IOC_NO_EDGE 0x00000000 /* No edge detection */
62 #define IOC_FALLING_EDGE 0x00010000 /* Edge detection on falling edge */
63 #define IOC_RISING_EDGE 0x00020000 /* Edge detection on rising edge */
64 #define IOC_BOTH_EDGES 0x00030000 /* Edge detection on both edges */
|
| /Zephyr-latest/doc/hardware/peripherals/edac/ |
| D | index.rst | 3 Error Detection And Correction (EDAC)
6 Error Detection And Correction is a mechanism used to detect and correct errors
|
| /Zephyr-latest/dts/bindings/input/ |
| D | st,stmpe811.yaml | 74 in the X+ line to the time the device performs touch detection.
76 minimize detection latency, but it could lower the position stability.
90 more latency in the touch detection process.
92 Use cases that require low touch detection latency
|
| /Zephyr-latest/drivers/edac/ |
| D | Kconfig | 7 bool "Error Detection and Correction (EDAC) drivers"
9 Enable Error Detection and Correction (EDAC) driver.
|
| /Zephyr-latest/drivers/watchdog/ |
| D | wdt_nxp_fs26.h | 128 /* Reaction on RSTB or FAIL SAFE outputs in case of OV detection on VMON_PRE */
135 /* Reaction on RSTB or FAIL SAFE outputs in case of UV detection on VMON_PRE */
142 /* Reaction on RSTB or FAIL SAFE outputs in case of OV detection on VMON_CORE */
149 /* Reaction on RSTB or FAIL SAFE outputs in case of UV detection on VMON_CORE */
156 /* Reaction on RSTB or FAIL SAFE outputs in case of OV detection on VMON_LDO1 */
163 /* Reaction on RSTB or FAIL SAFE outputs in case of UV detection on VMON_LDO1 */
170 /* Reaction on RSTB or FAIL SAFE outputs in case of OV detection on VMON_LDO2 */
177 /* Reaction on RSTB or FAIL SAFE outputs in case of UV detection on VMON_LDO2 */
186 /* Reaction on RSTB or FAIL SAFE outputs in case of OV detection on VMON_EXT */
193 /* Reaction on RSTB or FAIL SAFE outputs in case of UV detection on VMON_EXT */
[all …]
|
12345678910>>...12
