Searched full:configures (Results 1 – 25 of 185) sorted by relevance
12345678
| /Zephyr-latest/soc/arm/beetle/ |
| D | power.c | 64 * Configures the clock in active state.
77 * @brief Configures the clock that remain active during sleep state.
79 * Configures the clock that remain active during sleep state.
88 * @brief Configures the clock that remain active during deepsleep state.
90 * Configures the clock that remain active during deepsleep state.
113 * Configures the clocks and wakeup sources in the SoC.
|
| D | soc_power.h | 17 * Configures the clocks and wakeup sources in the SoC.
|
| /Zephyr-latest/tests/bsim/bluetooth/mesh/tests_scripts/bridge/ |
| D | brg_ivu.sh | 11 # 2. Provisioner configures itself and creates subnets equal to number of non-bridge devices.
12 # 3. Provisioner provisions and configures Subnet Bridge node to bridge the subnets.
13 # 4. Provisioner provisions and configures non-bridge devices for each subnet.
|
| D | brg_net_key_update.sh | 10 # 1. Tester configures itself and creates subnets equal to number of non-bridge nodes.
11 # 2. Tester provisions and configures Subnet Bridge node.
12 # 3. Tester provisions and configures non-bridge nodes for each subnet.
|
| D | brg_table_state_change.sh | 10 # 1. Tester configures itself and creates subnets equal to number of non-bridge nodes.
11 # 2. Tester provisions and configures Subnet Bridge node.
12 # 3. Tester provisions and configures non-bridge nodes for each subnet.
|
| D | brg_simple.sh | 26 # 1. Tester configures itself and creates subnets equal to number of non-bridge nodes.
27 # 2. Tester provisions and configures Subnet Bridge node to bridge the subnets.
28 # 3. Tester provisions and configures non-bridge nodes for each subnet.
|
| D | brg_persistent_storage.sh | 10 # 1. Tester configures itself and creates subnets equal to number of non-bridge nodes.
11 # 2. Tester provisions and configures Subnet Bridge node to bridge the subnets.
|
| D | brg_net_key_refresh.sh | 27 # 1. Tester configures itself and creates a subnet for the remote node.
28 # 2. Tester provisions and configures Subnet Bridge node.
29 # 3. Tester provisions and configures the non-bridge node for subnet 1.
|
| /Zephyr-latest/boards/nxp/lpcxpresso55s36/ |
| D | lpcxpresso55s36-pinctrl.dtsi | 13 /* Configures pin routing and optionally pin electrical features. */
22 /* Configures pin routing and optionally pin electrical features. */
31 /* Configures pin routing and optionally pin electrical features. */
50 /* Configures pin routing and optionally pin electrical features. */
59 /* Configures pins for CAN0 */
|
| /Zephyr-latest/include/zephyr/dt-bindings/gpio/ |
| D | gpio.h | 39 /* Configures GPIO output in single-ended mode (open drain or open source). */
41 /* Configures GPIO output in push-pull mode */
51 /** Configures GPIO output in open drain mode (wired AND).
58 /** Configures GPIO output in open source mode (wired OR).
83 * Configures GPIO interrupt to wakeup the system from low power mode.
|
| /Zephyr-latest/soc/nxp/s32/s32k1/ |
| D | Kconfig | 92 Configures the reset value of the FSEC register, which includes
101 Configures the reset value of the FOPT register, which includes boot,
109 Configures the reset value of the FEPROT register for FlexNVM
117 Configures the reset value of the FDPROT register for FlexNVM
|
| /Zephyr-latest/dts/bindings/flash_controller/ |
| D | nxp,kinetis-ftfa.yaml | 11 Configures the reset value of the FSEC register, which includes
18 Configures the reset value of the FOPT register, which includes boot,
|
| /Zephyr-latest/dts/bindings/bluetooth/ |
| D | zephyr,bt-hci-spi-slave.yaml | 5 Configures SPI slave settings for a Bluetooth controller that uses
18 The bt-hci@0 node configures an HCI SPI slave on SPI slave
|
| /Zephyr-latest/soc/nxp/kinetis/ |
| D | Kconfig | 109 Configures the reset value of the FSEC register, which includes
118 Configures the reset value of the FOPT register, which includes boot,
126 Configures the reset value of the FEPROT register for FlexNVM
134 Configures the reset value of the FDPROT register for FlexNVM
|
| /Zephyr-latest/cmake/compiler/host-gcc/ |
| D | generic.cmake | 3 # Configures CMake for using GCC
|
| /Zephyr-latest/dts/bindings/spi/ |
| D | nordic,nrf-spi-common.yaml | 50 - initially, SPI slave configures its WAKE line pin as an input and SPI
52 - when a transfer is to be performed, SPI master configures its WAKE
|
| /Zephyr-latest/cmake/bintools/host-gnu/ |
| D | target.cmake | 3 # Configures binary tools as host GNU binutils
|
| /Zephyr-latest/boards/native/native_posix/ |
| D | hw_counter.c | 51 * Configures the counter period.
119 * Configures the counter to generate an interrupt
|
| /Zephyr-latest/dts/bindings/clock/ |
| D | st,stm32h7-hsi-clock.yaml | 15 HSI clock divider. Configures the output HSI clock frequency
|
| /Zephyr-latest/scripts/native_simulator/native/src/ |
| D | hw_counter.c | 55 * Configures the counter period.
123 * Configures the counter to generate an interrupt
|
| /Zephyr-latest/dts/bindings/led/ |
| D | ti,lp5569.yaml | 22 If provided, configures the internal charge-pump mode in the MISC
|
| /Zephyr-latest/subsys/bluetooth/controller/ll_sw/nordic/hal/nrf5/radio/ |
| D | radio_df.h | 14 /* Function configures Radio with information about GPIO pins that may be
18 /* Configures GPIO pins in GPIO peripheral. The pins will be used for antenna
|
| /Zephyr-latest/dts/bindings/usb/ |
| D | usb-controller.yaml | 13 description: Configures USB controllers to work up to a specific
|
| /Zephyr-latest/cmake/bintools/armclang/ |
| D | target.cmake | 3 # Configures binary tools as mwdt binutils
|
| /Zephyr-latest/drivers/interrupt_controller/ |
| D | Kconfig.it8xxx2 | 15 Configures the maximum number of clients allowed per shared
|
12345678
