Searched refs:off (Results 251 – 275 of 436) sorted by relevance
1...<<1112131415161718
| /Zephyr-latest/doc/build/kconfig/ |
| D | menuconfig.rst | 163 off show-all mode, press :kbd:`A` in ``menuconfig`` or :kbd:`Ctrl-A` in
168 Show-all mode can't be turned off if there are no visible items in the
|
| /Zephyr-latest/boards/olimex/olimex_esp32_evb/doc/ |
| D | index.rst | 9 allows switching power appliances on and off.
13 power does not work when running off battery.
|
| /Zephyr-latest/doc/connectivity/bluetooth/shell/host/ |
| D | gap.rst | 23 may see a lot of lines printed on the shell. To stop the scan, run :code:`bt scan off`, the
40 uart:~$ bt scan off
110 advertising use the :code:`bt advertise off` command.
328 can make the shell not bondable using :code:`bt bondable off`. You can list all the devices you are
|
| /Zephyr-latest/doc/connectivity/bluetooth/api/mesh/ |
| D | shell.rst | 136 - Boolean values are denoted in the API documentation as ``<val(off, on)>``.
137 - ``on``, ``off``, ``enabled``, ``disabled``, ``1``, ``0``
144 ``mesh lpn set <value: off, on>``. Mandatory parameters are marked with angle brackets (e.g.
213 ``mesh lpn set <Val(off, on)>``
216 Enable or disable Low Power operation. Once enabled, the device will turn off its radio and
244 ``mesh test iv-update-test <Val(off, on)>``
288 ``mesh prov pb-gatt <Val(off, on)>``
301 ``mesh prov pb-adv <Val(off, on)>``
392 ``mesh prov beacon-listen <Val(off, on)>``
558 ``mesh models cfg beacon [Val(off, on)]``
[all …]
|
| /Zephyr-latest/doc/hardware/peripherals/can/ |
| D | controller.rst | 95 * Bus-off
104 bus-off state. In this state, the node is not allowed to send any dominant bits
105 to the bus. Nodes in the bus-off state may recover after receiving 128
|
| /Zephyr-latest/drivers/modem/ |
| D | Kconfig.ublox-sara-r4 | 51 This stack is used by the work queue to pass off net_pkt data
|
| /Zephyr-latest/drivers/clock_control/ |
| D | clock_control_mcux_syscon.c | 506 .off = mcux_lpc_syscon_clock_control_off,
|
| D | clock_control_mcux_ccm.c | 494 .off = mcux_ccm_off,
|
| D | clock_control_npcm.c | 306 .off = npcm_clock_control_off,
|
| /Zephyr-latest/dts/xtensa/intel/ |
| D | intel_adsp_cavs25.dtsi | 50 d3: off {
52 power-state-name = "soft-off";
|
| /Zephyr-latest/boards/nxp/frdm_k82f/doc/ |
| D | index.rst | 74 | FLASH | off-chip | QSPI flash |
84 | SENSOR | off-chip | fxos8700 polling; |
|
| /Zephyr-latest/boards/01space/esp32c3_042_oled/doc/ |
| D | index.rst | 60 | DISPLAY | off-chip | display |
|
| /Zephyr-latest/drivers/led/ |
| D | led_shell.c | 351 sub_led, SHELL_CMD_ARG(off, &dsub_device_name, "<device> <led>", cmd_off, 3, 0),
|
| D | lp50xx.c | 343 .off = lp50xx_off,
|
| /Zephyr-latest/drivers/wifi/esp_at/ |
| D | Kconfig.esp_at | 53 This stack is used by the work queue to pass off net_pkt data
|
| /Zephyr-latest/cmake/compiler/ |
| D | compiler_flags_template.cmake | 122 # Compiler flag for turning off thread-safe initialization of local statics
|
| /Zephyr-latest/subsys/pm/ |
| D | Kconfig | 64 necessary power management operations like turning off
|
| /Zephyr-latest/boards/u-blox/ubx_bmd340eval/doc/ |
| D | index.rst | 159 | 7 | Cut off |
163 | 9 | Cut off |
|
| /Zephyr-latest/boards/u-blox/ubx_bmd345eval/doc/ |
| D | index.rst | 172 | 7 | Cut off |
176 | 9 | Cut off |
|
| /Zephyr-latest/boards/u-blox/ubx_bmd380eval/doc/ |
| D | index.rst | 161 | 7 | Cut off |
165 | 9 | Cut off |
|
| /Zephyr-latest/doc/develop/test/ |
| D | bsim.rst | 161 Please follow the existing conventions and do not design one-off bespoke runners (e.g. a python
190 off, and powering up after as a new simulation) should use separate simulation ids for each
|
| /Zephyr-latest/subsys/shell/ |
| D | Kconfig | 198 Meta keys will not be active when shell echo is set to off.
256 The resize command can be turned off to save code memory (~0,5k).
|
| /Zephyr-latest/boards/espressif/esp32_ethernet_kit/doc/ |
| D | index.rst | 103 board on, toggling to **GND** position powers the board off.
158 (B), the USB power will be automatically cut off.
394 low, turning the clock output off. After power-on you can control
396 `RMII Clock Sourced Externally by PHY`_. For PHYs that cannot turn off
|
| /Zephyr-latest/subsys/net/ip/ |
| D | Kconfig.mgmt | 103 "net events [on|off]" command. The monitoring is disabled by
|
| /Zephyr-latest/soc/nxp/imxrt/ |
| D | Kconfig | 123 The M4 image will be loaded from flash into RAM based off a
|
1...<<1112131415161718
