Home
last modified time | relevance | path

Searched refs:automatic (Results 1 – 25 of 55) sorted by relevance

123

/Zephyr-latest/tests/subsys/usb/uac2/
Dapp.overlay36 automatic-gain-control =
67 automatic-gain-control =
/Zephyr-latest/samples/boards/st/power_mgmt/serial_wakeup/boards/
Db_u585i_iot02a.overlay8 /* USART Wakeup requires automatic HSI16 switch on in deepsleep mode
Dnucleo_wb55rg.overlay9 /* USART Wakeup requires automatic HSI16 switch on in deepsleep mode
/Zephyr-latest/samples/drivers/mspi/mspi_flash/
DREADME.rst12 allows confirmation that the flash is working and that automatic power
/Zephyr-latest/samples/drivers/spi_flash/
DREADME.rst12 allows confirmation that the flash is working and that automatic power
/Zephyr-latest/doc/services/debugging/
Dthread-analyzer.rst80 The time for which the module sleeps between consecutive printing of thread analysis in automatic
83 The stack for thread analyzer automatic thread.
/Zephyr-latest/drivers/serial/
DKconfig.ns1655055 This enables support for 64-bytes FIFO and automatic hardware
61 This enables support for 128-bytes FIFO and automatic hardware flow control.
/Zephyr-latest/doc/hardware/peripherals/sensor/
Dpower_management.rst18 In the future, with :ref:`sensor-read-and-decode` its possible that automatic management of device …
/Zephyr-latest/drivers/modem/
DKconfig.ublox-sara-r437 Enable automatic detection of modem variant (SARA-R4 or SARA-U2)
66 Enable automatic detection of the APN, based on the IMSI
/Zephyr-latest/tests/kernel/timer/starve/
DREADME.txt11 This test is not run in automatic test suites because it generally takes
/Zephyr-latest/doc/connectivity/networking/api/
Dnet_config.rst14 semi-automatic way during the system boot, based on user-supplied
74 If you want to use the network configuration library but without automatic
/Zephyr-latest/drivers/espi/
DKconfig.npcx102 int "A timeout value in microseconds to wait for automatic read status"
107 automatic read status.
DKconfig64 Enable automatic acknowledgment from eSPI target towards eSPI controller
75 Enable automatic acknowledgment from target basic configuration been
/Zephyr-latest/subsys/fs/nvs/
DKconfig43 Enable automatic initialization of a NVS on a memory region that does
/Zephyr-latest/drivers/flash/
DKconfig.simulator91 This number is not automatic because implementation uses
/Zephyr-latest/arch/common/
DKconfig17 (automatic) use of the -semihosting-config switch when invoking it.
/Zephyr-latest/doc/develop/toolchains/
Dzephyr_sdk.rst41 the operating system specific instructions below) and you want automatic discovery
48 containing multiple Zephyr SDKs, allowing for automatic toolchain selection. For
/Zephyr-latest/drivers/can/
DKconfig94 Enable support for manual (non-automatic) recovery from bus-off state. Not all CAN
/Zephyr-latest/modules/lvgl/
DKconfig150 Priority used for the automatic initialization of LVGL.
/Zephyr-latest/doc/develop/sca/
Declair.rst11 freedom from interference among software components, to the automatic
/Zephyr-latest/doc/releases/
Dmigration-guide-4.0.rst427 automatic resumption. To disable the automatic resumption, use
461 Legacy Advertising API not using automatic resumption
469 Legacy Advertising API using automatic resumption
/Zephyr-latest/share/zephyr-package/cmake/
DZephyrConfig.cmake7 # - Support automatic Zephyr installation lookup through the use of find_package(ZEPHYR)
/Zephyr-latest/samples/subsys/usb/dfu/
DREADME.rst111 Permanent download and automatic reboot
/Zephyr-latest/drivers/gpio/
DKconfig77 automatic GPIO configuration via devicetree.
/Zephyr-latest/boards/heltec/heltec_wireless_stick_lite_v3/doc/
Dindex.rst16 …nagement, overcharge protection, battery power detection, USB / battery power automatic switching).

123