Searched refs:between (Results 1 – 25 of 548) sorted by relevance
12345678910>>...22
22 * - Connect LPADC0 CH0A signal to voltage between 0~1.8V (J30 pin 1)23 * - Connect LPADC0 CH0B signal to voltage between 0~1.8V (J30 pin 2)25 * - Connect LPADC0 CH2A signal to voltage between 0~1.8V (J30 pin 3)
24 * - Connect LPADC0 CH0A signal to voltage between 0~3.3V (P19 pin 4)25 * - Connect LPADC0 CH0B signal to voltage between 0~3.3V (P19 pin 2)27 * - Connect LPADC0 CH4A signal to voltage between 0~3.3V (P17 pin 19)29 * - Connect LPADC0 CH4B signal to voltage between 0~3.3V (P18 pin 1)
9 Use interleaved packing between BIS ISO stream subevents.12 int "Interval between each packet report"
7 int "Delay between LED updates in ms"10 Delay between LED updates in ms.
15 * LED1 connection must be manually established using a jumper between23 * LED2 connection must be manually established using a jumper between61 * Interrupt connection must be manually established using a jumper wire between
24 * - Connect LPADC0 CH0A signal to voltage between 0~1.8V (J30 pin 1)25 * - Connect LPADC0 CH0B signal to voltage between 0~1.8V (J30 pin 2)27 * - Connect LPADC0 CH2A signal to voltage between 0~1.8V (J30 pin 3)
24 * - Connect LPADC0 CH1A signal to voltage between 0~1.8V (J4 pin 4)25 * - Connect LPADC0 CH1B signal to voltage between 0~1.8V (J8 pin 11)27 * - Connect LPADC0 CH2A signal to voltage between 0~1.8V (J8 pin 12)
24 * - Connect LPADC0 CH1A signal to voltage between 0~1.8V (J8 pin 20)25 * - Connect LPADC0 CH1B signal to voltage between 0~1.8V (J8 pin 24)27 * - Connect LPADC0 CH2A signal to voltage between 0~1.8V (J8 pin 28)
24 * - Connect LPADC0 CH0A signal to voltage between 0~1.8V (J30 pin 1)25 * - Connect LPADC0 CH0B signal to voltage between 0~1.8V (J30 pin 2)
18 parameter. Any dependencies between the various TFM_PARTITION_*29 parameter. Any dependencies between the various TFM_PARTITION_*40 parameter. Any dependencies between the various TFM_PARTITION_*52 parameter. Any dependencies between the various TFM_PARTITION_*63 parameter. Any dependencies between the various TFM_PARTITION_*75 parameter. Any dependencies between the various TFM_PARTITION_*
22 int "Sleep time between reboot countdown iterations (in milliseconds)"26 Duration in milliseconds to sleep between reboot countdown iterations.
27 * Here IP packets are exchanged between Zephyr and the host system via serial33 * Here IP packets are exchanged between Zephyr and the host system via QEMU's50 routes TCP and UDP traffic between the guest and host. It uses the user mode76 and want to create a connection between them, see79 * Simulating IEEE 802.15.4 network between two QEMUs.82 run over an UART between them.90 packets are bridged between those two interfaces.
10 This page describes how to set up a virtual network between two QEMUs that12 between them. Note that this only works in Linux host.47 If you want to capture the network traffic between the two QEMUs, type:76 You should see data passed between the two QEMUs.
4 Play pong as single player or over Bluetooth between two micro:bit devices.9 Play pong as single player or over Bluetooth between two micro:bit14 button A to toggle between single- and multi-player, and press button B
9 int "Interval between each packet report"19 This may be needed if report printouts are to be synchronized between
23 int "Time between rechecks of transaction status (us)"27 busy wait between checks of the MDIO transaction status.
47 # Note- This config present the offest between container header and user51 hex "The offset between container header and user image"54 The offset between container and user image. IF change the user image
23 clocks underlying the cycle counter, the offset between time estimated from29 * :ref:`converting between time representations <timeutil_repr>`82 * The relative error between observable instants in each scale, required to88 Synchronization or alignment between time scales is done with a multi-step125 value, e.g. jumping forward or back when going between successive instants.142 changes in Earth’s rotation. Thus the difference between TAI and UT varies171 difference between TAI and UTC from 36 seconds to 37 seconds. There was173 between TAI and UTC was only 32 seconds. The following table shows196 There are two stages required to support conversion between Zephyr time and199 * Translation between the continuous but inaccurate Zephyr time scale and an[all …]
28 int "Delay between TX retries in milliseconds"31 Sleep period between TX retry attempts.
25 int "Threshold of eCO2 between low and medium"30 int "Threshold of eCO2 between medium and high"
18 (disable interference reduction between D/A and A/D conversion).20 (enable interference reduction between D/A and A/D conversion).
10 * buffer between DAC and ADC.
5 * Test requires jumper between:
