Searched refs:GPIO_INT_EDGE_FALLING (Results 1 – 24 of 24) sorted by relevance
| /Zephyr-latest/drivers/sensor/ti/ina23x/ |
| D | ina23x_trigger.c | 49 GPIO_INT_EDGE_FALLING); in ina23x_trigger_mode_init()
|
| /Zephyr-latest/drivers/sensor/vishay/vcnl36825t/ |
| D | vcnl36825t_trigger.c | 103 rc = gpio_pin_interrupt_configure_dt(&config->int_gpio, GPIO_INT_EDGE_FALLING); in vcnl36825t_thread_cb()
215 rc = gpio_pin_interrupt_configure_dt(&config->int_gpio, GPIO_INT_EDGE_FALLING); in vcnl36825t_trigger_set()
|
| /Zephyr-latest/drivers/wifi/infineon/ |
| D | airoc_whd_hal_spi.c | 250 gpio, (oob_config->is_falling_edge == WHD_TRUE) ? GPIO_INT_EDGE_FALLING in whd_bus_spi_irq_enable()
272 gpio, (oob_config->is_falling_edge == WHD_TRUE) ? GPIO_INT_EDGE_FALLING in whd_bus_spi_irq_enable()
|
| /Zephyr-latest/drivers/sensor/ti/tmag5170/ |
| D | tmag5170_trigger.c | 143 ret = gpio_pin_interrupt_configure_dt(&cfg->int_gpio, GPIO_INT_EDGE_FALLING); in tmag5170_trigger_init()
|
| /Zephyr-latest/tests/drivers/gpio/gpio_basic_api/src/ |
| D | test_callback_trigger.c | 125 zassert_equal(test_callback(GPIO_INT_EDGE_FALLING), TC_PASS, in ZTEST()
|
| /Zephyr-latest/drivers/input/ |
| D | input_ili2132a.c | 120 ret = gpio_pin_interrupt_configure_dt(&dev_cfg->irq, GPIO_INT_EDGE_FALLING); in ili2132a_init()
|
| /Zephyr-latest/drivers/sensor/memsic/mc3419/ |
| D | mc3419_trigger.c | 126 gpio_pin_interrupt_configure_dt(&cfg->int_gpio, GPIO_INT_EDGE_FALLING); in mc3419_configure_trigger()
|
| /Zephyr-latest/drivers/gpio/ |
| D | gpio_mchp_mss.c | 172 case GPIO_INT_EDGE_FALLING: in mss_gpio_pin_interrupt_configure()
|
| D | gpio_andes_atcgpio100.c | 234 case GPIO_INT_EDGE_FALLING: in gpio_atcgpio100_pin_interrupt_configure()
|
| D | gpio_emul.c | 215 case GPIO_INT_EDGE_FALLING: in gpio_emul_gen_interrupt_bits()
|
| /Zephyr-latest/tests/drivers/gpio/gpio_api_1pin/src/ |
| D | test_pin_interrupt.c | 217 test_gpio_pin_interrupt_edge(0, GPIO_INT_EDGE_FALLING); in ZTEST()
|
| /Zephyr-latest/drivers/bluetooth/hci/ |
| D | apollox_blue.c | 101 gpio_pin_interrupt_configure_dt(&clkreq_gpio, GPIO_INT_EDGE_FALLING); in bt_clkreq_isr()
|
| /Zephyr-latest/subsys/mgmt/ec_host_cmd/backends/ |
| D | ec_host_cmd_backend_shi_ite.c | 474 ret = gpio_pin_interrupt_configure(cfg->cs.port, cfg->cs.pin, GPIO_INT_EDGE_FALLING); in shi_ite_init()
|
| /Zephyr-latest/drivers/usb_c/ppc/ |
| D | nxp_nx20p3483.c | 384 GPIO_INT_EDGE_FALLING); in nx20p3483_dev_init()
|
| /Zephyr-latest/drivers/rtc/ |
| D | rtc_pcf8563.c | 437 ret = gpio_pin_interrupt_configure_dt(&config->int1, GPIO_INT_EDGE_FALLING); in pcf8563_alarm_set_callback()
|
| D | rtc_rv8263.c | 345 err = gpio_pin_interrupt_configure_dt(&config->int_gpio, GPIO_INT_EDGE_FALLING); in rv8263c8_init()
|
| /Zephyr-latest/drivers/usb/bc12/ |
| D | bc12_pi3usb9201.c | 596 rv = gpio_pin_interrupt_configure_dt(&cfg->intb_gpio, GPIO_INT_EDGE_FALLING); in pi3usb9201_init()
|
| /Zephyr-latest/drivers/led/ |
| D | ht16k33.c | 388 GPIO_INT_EDGE_FALLING); in ht16k33_init()
|
| /Zephyr-latest/drivers/ethernet/phy/ |
| D | phy_tja1103.c | 321 ret = gpio_pin_interrupt_configure_dt(&cfg->gpio_interrupt, GPIO_INT_EDGE_FALLING); in phy_tja1103_cfg_irq_poll()
|
| /Zephyr-latest/drivers/ethernet/ |
| D | eth_w5500.c | 559 GPIO_INT_EDGE_FALLING); in w5500_init()
|
| /Zephyr-latest/drivers/sensor/st/lis2dh/ |
| D | lis2dh_trigger.c | 24 GPIO_INT_EDGE_FALLING,
|
| /Zephyr-latest/drivers/watchdog/ |
| D | wdt_nxp_fs26.c | 662 GPIO_INT_EDGE_FALLING)) { in wdt_nxp_fs26_init()
|
| /Zephyr-latest/drivers/adc/ |
| D | adc_ads1x1x.c | 185 ? GPIO_INT_EDGE_FALLING in ads1x1x_setup_rdy_interrupt()
|
| /Zephyr-latest/include/zephyr/drivers/ |
| D | gpio.h | 168 #define GPIO_INT_EDGE_FALLING (GPIO_INT_ENABLE | \ macro
|
