Searched full:triggering (Results 1 – 25 of 174) sorted by relevance
1234567
| /Zephyr-latest/include/zephyr/dt-bindings/dma/ |
| D | dma_smartbond.h | 11 * @brief Vendror-specific DMA peripheral triggering sources.
13 * A valid triggering source should be provided when DMA
|
| /Zephyr-latest/include/zephyr/drivers/dma/ |
| D | dma_smartbond.h | 11 * @brief Vendror-specific DMA peripheral triggering sources.
13 * A valid triggering source should be provided when DMA
|
| /Zephyr-latest/dts/bindings/sensor/ |
| D | microchip,tcn75a.yaml | 18 triggering support.
40 Oneshot sampling mode. Reduces power consumption, but disables triggering
|
| /Zephyr-latest/dts/bindings/mfd/ |
| D | nordic,npm2100.yaml | 25 Using interrupt level triggering instead of edge triggering
|
| /Zephyr-latest/drivers/sensor/bosch/bmi08x/ |
| D | Kconfig | 24 Specify the type of triggering to be used by the driver.
64 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/subsys/testsuite/include/zephyr/ |
| D | interrupt_util.h | 46 * triggering. Return the NVIC line in get_available_nvic_line()
62 printk("Triggering irq : %d\n", irq); in trigger_irq()
79 printk("Triggering irq : %d\n", irq); in trigger_irq()
102 printk("Triggering irq : %d\n", irq); in trigger_irq()
|
| /Zephyr-latest/dts/bindings/misc/ |
| D | nxp,s32-trgmux.yaml | 6 The device supports the triggering scheme between peripherals.
|
| /Zephyr-latest/samples/sensor/6dof_motion_drdy/ |
| D | prj.conf | 18 # Trigger mode: sample is using interrupt triggering
|
| /Zephyr-latest/samples/sensor/tdk_apex/ |
| D | prj.conf | 18 # Trigger mode: sample is using interrupt triggering
|
| /Zephyr-latest/drivers/sensor/ams/tmd2620/ |
| D | Kconfig | 18 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/dts/bindings/tcpc/ |
| D | parade,ps8xxx.yaml | 18 Alert pin from the TCPC triggering interrupt
|
| /Zephyr-latest/modules/openthread/platform/ |
| D | misc.c | 53 * To enable resetting to bootloader by triggering gpio pin, in otPlatResetToBootloader()
82 * triggering reset had no effect) in otPlatResetToBootloader()
|
| /Zephyr-latest/drivers/sensor/honeywell/sm351lt/ |
| D | Kconfig | 20 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/drivers/ethernet/phy/ |
| D | Kconfig.dm8806 | 20 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/drivers/sensor/lm75/ |
| D | Kconfig | 21 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/drivers/sensor/memsic/mc3419/ |
| D | Kconfig | 24 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/drivers/sensor/tdk/icm42605/ |
| D | Kconfig | 20 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/dts/bindings/options/ |
| D | openthread,config.yaml | 29 This enables resetting to bootloader by triggering given GPIO pin. Property represents
|
| /Zephyr-latest/drivers/sensor/ti/tmp007/ |
| D | Kconfig | 20 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/drivers/sensor/vishay/vcnl36825t/ |
| D | Kconfig | 23 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/drivers/sensor/ |
| D | Kconfig.trigger_template | 8 Specify the type of triggering to be used by the sensor module.
|
| /Zephyr-latest/drivers/sensor/amg88xx/ |
| D | Kconfig | 20 Specify the type of triggering used by the driver.
|
| /Zephyr-latest/drivers/sensor/ams/tsl2540/ |
| D | Kconfig | 23 Specify the type of triggering to be used by the driver.
|
| /Zephyr-latest/drivers/sensor/ti/fdc2x1x/ |
| D | Kconfig | 21 Specify the type of triggering used by the driver.
|
| /Zephyr-latest/drivers/sensor/vishay/vcnl4040/ |
| D | Kconfig | 28 Specify the type of triggering to be used by the driver.
|
1234567
