Home
last modified time | relevance | path

Searched full:trigger (Results 1 – 25 of 920) sorted by relevance

12345678910>>...37

/Zephyr-latest/drivers/sensor/lm77/
DKconfig19 bool "Trigger support"
24 Enable trigger support for the LM77 digital temperature sensor.
26 Trigger events are based on the LM77 INT signal (configured for event
27 interrupt mode). After a trigger event the LM77 temperature must be
28 read in order to reset and rearm the trigger.
33 int "Stack size for the trigger workqueue thread"
36 Size of the stack used for the internal trigger workqueue thread.
39 int "Priority for the trigger workqueue thread"
42 Priority level for the internal trigger workqueue thread.
/Zephyr-latest/include/zephyr/drivers/
Dcomparator.h26 /** Comparator trigger enumerations */
28 /** No trigger */
30 /** Trigger on rising edge of comparator output */
32 /** Trigger on falling edge of comparator output */
34 /** Trigger on both edges of comparator output */
45 enum comparator_trigger trigger);
77 * @brief Set comparator's trigger
80 * @param trigger Trigger for signal and callback
86 enum comparator_trigger trigger);
89 enum comparator_trigger trigger) in z_impl_comparator_set_trigger() argument
[all …]
/Zephyr-latest/include/zephyr/drivers/dma/
Ddma_mcux_lpc.h11 * LPC DMA engine channel hardware trigger attributes.
22 /* Hardware trigger enable. When set, the hardware trigger connected to this
23 * channel via INPUTMUX can be used to trigger a transfer
27 /* HW trigger polarity. When this bit is set, the trigger will be active
32 /* HW trigger type. When this bit is set, the trigger will be level triggered.
33 * When it is cleared, the hardware trigger will be edge triggered.
37 /* HW trigger burst mode. When set, the hardware trigger will cause a burst
44 /* HW trigger burst power. Note that due to the size limit of the dma_slot
/Zephyr-latest/tests/drivers/i2s/i2s_api/src/
Dtest_i2s_loopback.c15 * - TX stream START trigger starts transmission.
16 * - RX stream START trigger starts reception.
18 * - TX stream DRAIN trigger empties the transmit queue.
19 * - RX stream STOP trigger stops reception.
42 zassert_equal(ret, 0, "RX START trigger failed"); in ZTEST_USER()
46 zassert_equal(ret, 0, "TX START trigger failed"); in ZTEST_USER()
58 zassert_equal(ret, 0, "TX DRAIN trigger failed"); in ZTEST_USER()
66 zassert_equal(ret, 0, "RX STOP trigger failed"); in ZTEST_USER()
81 * - TX stream START trigger starts transmission.
82 * - RX stream START trigger starts reception.
[all …]
Dtest_i2s_dir_both_loopback.c20 * - START trigger starts both the transmission and reception.
22 * - DRAIN trigger empties the transmit queue and stops both streams.
44 zassert_equal(ret, 0, "RX/TX START trigger failed\n"); in ZTEST_USER()
56 zassert_equal(ret, 0, "RX/TX DRAIN trigger failed"); in ZTEST_USER()
75 * - START trigger starts both the transmission and reception.
77 * - DRAIN trigger empties the transmit queue and stops both streams.
94 zassert_equal(ret, 0, "RX/TX START trigger failed\n"); in ZTEST_USER()
108 zassert_equal(ret, 0, "RX/TX DRAIN trigger failed"); in ZTEST_USER()
120 * - STOP trigger stops transfer / reception at the end of the current block,
121 * consecutive START trigger restarts transfer / reception with the next data
[all …]
Dtest_i2s_states.c14 * - Sending START, DRAIN, STOP, DROP, PREPARE trigger in NOT_READY state
77 * - Sending DRAIN, STOP, PREPARE trigger in READY state returns failure.
118 * - Sending START, PREPARE trigger in RUNNING state returns failure.
136 zassert_equal(ret, 0, "RX START trigger failed"); in ZTEST_USER()
140 zassert_equal(ret, 0, "TX START trigger failed"); in ZTEST_USER()
162 zassert_equal(ret, 0, "TX DRAIN trigger failed"); in ZTEST_USER()
166 zassert_equal(ret, 0, "RX STOP trigger failed"); in ZTEST_USER()
174 * - Sending START, STOP, DRAIN, PREPARE trigger in STOPPING state returns
193 zassert_equal(ret, 0, "RX START trigger failed"); in ZTEST_USER()
197 zassert_equal(ret, 0, "TX START trigger failed"); in ZTEST_USER()
[all …]
/Zephyr-latest/tests/arch/arm/arm_runtime_nmi/
DREADME.txt34 Trigger NMI in 10s: 0 s
35 Trigger NMI in 10s: 1 s
36 Trigger NMI in 10s: 2 s
37 Trigger NMI in 10s: 3 s
38 Trigger NMI in 10s: 4 s
39 Trigger NMI in 10s: 5 s
40 Trigger NMI in 10s: 6 s
41 Trigger NMI in 10s: 7 s
42 Trigger NMI in 10s: 8 s
43 Trigger NMI in 10s: 9 s
/Zephyr-latest/include/zephyr/drivers/interrupt_controller/
Dgd32_exti.h15 * @name EXTI trigger modes.
20 /** No trigger */
22 /** Trigger on rising edge */
24 /** Trigger on falling edge */
26 /** Trigger on rising and falling edge */
49 * @brief Configure EXTI interrupt trigger mode for the given line.
52 * @param trigger Trigger mode (see @ref GD32_EXTI_TRIG).
54 void gd32_exti_trigger(uint8_t line, uint8_t trigger);
Dgpio_intc_stm32.h47 * @brief GPIO interrupt trigger flags
50 /* No trigger */
52 /* Trigger on rising edge */
54 /* Trigger on falling edge */
56 /* Trigger on both rising and falling edge */
58 /* Trigger on high level */
60 /* Trigger on low level */
65 * @brief Select trigger for interrupt on specified GPIO line
68 * @param trg Interrupt trigger (see @ref stm32_gpio_irq_trigger)
Dwuc_ite_it8xxx2.h14 * @brief A trigger condition on the corresponding input generates
23 * @brief A trigger condition on the corresponding input doesn't
32 * @brief Write-1-clear a trigger condition that occurs on the
41 * @brief Select the trigger edge mode on the corresponding input
45 * @param flags Select the trigger edge mode
/Zephyr-latest/subsys/bluetooth/audio/
Dmpl_internal.h112 /** Trigger player name changed callback */
115 /** Trigger player name changed callback */
118 /* Trigger track changed callback */
121 /* Trigger title changed callback */
124 /* Trigger duration changed callback */
127 /* Trigger position changed callback */
130 /* Trigger playback speed changed callback */
133 /* Trigger seeking speed changed callback */
136 /* Trigger current track id changed callback */
139 /* Trigger next track id changed callback */
[all …]
/Zephyr-latest/drivers/sensor/lm75/
DKconfig18 prompt "Trigger mode"
24 bool "No trigger"
40 int "Stack size for the trigger workqueue thread"
43 Size of the stack used for the internal trigger workqueue thread.
46 int "Priority for the trigger workqueue thread"
49 Priority level for the internal trigger workqueue thread.
/Zephyr-latest/drivers/sensor/
Dsensor_shell_stream.c72 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_DOUBLE_TAP; in cmd_sensor_stream()
74 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_DATA_READY; in cmd_sensor_stream()
76 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_DELTA; in cmd_sensor_stream()
78 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_FREEFALL; in cmd_sensor_stream()
80 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_MOTION; in cmd_sensor_stream()
82 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_NEAR_FAR; in cmd_sensor_stream()
84 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_STATIONARY; in cmd_sensor_stream()
86 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_THRESHOLD; in cmd_sensor_stream()
88 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_FIFO_WATERMARK; in cmd_sensor_stream()
90 iodev_sensor_shell_trigger.trigger = SENSOR_TRIG_FIFO_FULL; in cmd_sensor_stream()
[all …]
/Zephyr-latest/samples/sensor/bmg160/src/
Dmain.c73 const struct sensor_trigger *trigger) in trigger_handler() argument
75 if (trigger->type != SENSOR_TRIG_DATA_READY && in trigger_handler()
76 trigger->type != SENSOR_TRIG_DELTA) { in trigger_handler()
77 printf("Gyro: trigger handler: unknown trigger type.\n"); in trigger_handler()
97 printf("Gyro: Testing anymotion trigger.\n"); in test_trigger_mode()
99 /* set up the trigger */ in test_trigger_mode()
122 printf("Gyro: cannot set trigger.\n"); in test_trigger_mode()
133 printf("Gyro: cannot clear trigger.\n"); in test_trigger_mode()
137 printf("Gyro: Anymotion trigger test finished.\n"); in test_trigger_mode()
139 printf("Gyro: Testing data ready trigger.\n"); in test_trigger_mode()
[all …]
/Zephyr-latest/samples/sensor/apds9960/
DREADME.rst12 sensor in polling mode (without an interrupt trigger).
32 ambient light intensity without trigger is 387
33 proxy without trigger is 115
34 ambient light intensity without trigger is 386
35 proxy without trigger is 112
36 ambient light intensity without trigger is 386
/Zephyr-latest/scripts/build/
Dsubfolder_list.py32 parser.add_argument('-t', '--trigger-file', required=False,
33 help='Trigger file to be touched to re-run CMake')
91 def touch(trigger): argument
92 """Touch the trigger file
94 If no trigger file is provided then do a return.
97 if trigger is None:
100 if os.path.exists(trigger):
101 os.utime(trigger, None)
103 with open(trigger, 'w') as trigger_fo:
114 # Always touch trigger file to ensure json files are updated
/Zephyr-latest/samples/sensor/vcnl4040/
DREADME.rst5 Get proximity and ambient light data from a VCNL4040 sensor (polling & trigger mode).
11 5 sec in the interval of 300msec in polling mode. Then threshold trigger mode
50 Testing the trigger mode.
51 Testing proximity trigger.
58 Threshold trigger test finished.
59 Trigger mode test finished.
/Zephyr-latest/drivers/serial/
DKconfig.xmc4xxx21 bool "Continue to trigger fifo rx interrupt"
24 When this option is enabled, an interrupt will continue to trigger
26 trigger only once on the first received byte. The receive fifo will
27 need to be fully flushed so that the interrupt will trigger again.
/Zephyr-latest/samples/sensor/ccs811/
DKconfig10 prompt "CCS811 Trigger On"
14 Select the type of trigger to use
17 bool "Trigger on data ready"
20 bool "Trigger on eCO2 threshold crossing"
/Zephyr-latest/subsys/bluetooth/audio/shell/
Dmpl.c238 "Trigger Player Name changed callback (test)",
241 "Trigger Player icon URL changed callback (test)",
244 "Trigger Track Changed callback (test)",
247 "Trigger Track Title callback (test)",
250 "Trigger Track Duration callback (test)",
253 "Trigger Track Position callback (test)",
256 "Trigger Playback Speed callback (test)",
259 "Trigger Seeking Speed callback (test)",
263 "Trigger Current Track callback (test)",
266 "Trigger Next Track callback (test)",
[all …]
/Zephyr-latest/drivers/sensor/memsic/mc3419/
DKconfig16 bool "Trigger mode"
21 prompt "Trigger mode"
27 bool "No trigger"
33 Enable trigger to run in own thread. By
/Zephyr-latest/boards/sparkfun/thing_plus_matter_mgm240p/dts/bindings/
Dsilabs,gecko-wake-up-trigger.yaml4 description: GPIO Wake Up Trigger for EFR32MG24
6 compatible: "silabs,gecko-wake-up-trigger"
15 GPIO used as wake up trigger from EM4 sleep
/Zephyr-latest/boards/silabs/dev_kits/xg24_dk2601b/dts/bindings/
Dsilabs,gecko-wake-up-trigger.yaml4 description: GPIO Wake Up Trigger for EFR32MG24
6 compatible: "silabs,gecko-wake-up-trigger"
15 GPIO used as wake up trigger from EM4 sleep
/Zephyr-latest/boards/silabs/dev_kits/xg24_ek2703a/dts/bindings/
Dsilabs,gecko-wake-up-trigger.yaml4 description: GPIO Wake Up Trigger for EFR32MG24
6 compatible: "silabs,gecko-wake-up-trigger"
15 GPIO used as wake up trigger from EM4 sleep
/Zephyr-latest/boards/silabs/dev_kits/sltb010a/dts/bindings/
Dsilabs,gecko-wake-up-triggers.yaml4 description: GPIO Wake Up Trigger for EFR32BG22/EFR32BG27
6 compatible: "silabs,gecko-wake-up-trigger"
15 GPIO used as wake up trigger from EM4 sleep

12345678910>>...37