Searched full:stand (Results 1 – 25 of 53) sorted by relevance
123
| /Zephyr-latest/drivers/ethernet/ |
| D | Kconfig.lan9250 | 1 # LAN9250 Stand-alone Ethernet Controller configuration options
13 LAN9250 Stand-Alone Ethernet Controller
|
| D | Kconfig.enc424j600 | 12 ENC424J600C Stand-Alone Ethernet Controller
|
| D | Kconfig.w5500 | 13 W5500 Stand-Alone Ethernet Controller
|
| D | Kconfig.enc28j60 | 12 ENC28J60C Stand-Alone Ethernet Controller
|
| D | eth_w5500_priv.h | 1 /* W5500 Stand-alone Ethernet Controller with SPI
|
| D | eth_enc28j60_priv.h | 1 /* ENC28J60 Stand-alone Ethernet Controller with SPI
|
| D | eth_enc424j600_priv.h | 1 /* ENC424J600 Stand-alone Ethernet Controller with SPI
|
| D | eth_lan9250_priv.h | 1 /* LAN9250 Stand-alone Ethernet Controller with SPI
|
| /Zephyr-latest/samples/drivers/can/counter/ |
| D | README.rst | 26 with a stand alone CAN controller.
38 Stand alone CAN controller
|
| /Zephyr-latest/dts/bindings/sensor/ |
| D | ti,tmag5170.yaml | 23 1 - stand-by mode - in this mode the device waits for application to trigger
28 3 - active trigger mode - in this mode, similar to stand-by mode, the device
30 the conversion is shorter than in stand-by mode, on the cost of increased power
|
| /Zephyr-latest/samples/boards/bbc/microbit/line_follower_robot/ |
| D | README.rst | 9 This sample controls a stand-alone line-following DFRobot Maqueen
|
| /Zephyr-latest/doc/connectivity/networking/ |
| D | native_sim_setup.rst | 26 or installed stand alone from its own git repository:
122 or installed stand alone from its own git repository:
|
| D | qemu_eth_setup.rst | 23 or installed stand alone from its own git repository:
|
| D | networking_with_multiple_instances.rst | 20 or installed stand alone from its own git repository:
|
| /Zephyr-latest/boards/shields/mcp2515/doc/ |
| D | index.rst | 7 Stand-Alone CAN Controller with SPI Interface.
15 The DFRobot CAN BUS shield supports the Microchip MCP2515 stand-alone CAN
28 - Stand-Alone CAN 2.0B Controller
124 The Keyestudio CAN BUS shield supports the Microchip MCP2515 stand-alone CAN
139 - Stand-Alone CAN 2.0B Controller
244 - Stand-Alone CAN 2.0B Controller
383 …http://ww1.microchip.com/downloads/en/DeviceDoc/MCP2515-Stand-Alone-CAN-Controller-with-SPI-200018…
|
| /Zephyr-latest/dts/bindings/stepper/adi/ |
| D | adi,trinamic-ramp-generator.yaml | 87 short circuit for motor stand still
|
| /Zephyr-latest/boards/shields/arceli_eth_w5500/doc/ |
| D | index.rst | 10 `W5500`_ is 10/100 MBPS stand alone Ethernet controller with on-board MAC & PHY,
|
| /Zephyr-latest/dts/bindings/gpio/ |
| D | adi,max22190-gpio.yaml | 88 WBE bit in all Filter registers stand for wire break enable on each
|
| /Zephyr-latest/boards/shields/mikroe_eth3_click/doc/ |
| D | index.rst | 10 a 10/100Mbps BASE-T stand alone Ethernet Controller with an on-board MAC & PHY,
|
| /Zephyr-latest/boards/shields/mikroe_eth_click/doc/ |
| D | index.rst | 10 a 28-pin, 10BASE-T stand alone Ethernet Controller with an on-board MAC & PHY,
|
| /Zephyr-latest/boards/shields/seeed_w5500/doc/ |
| D | index.rst | 11 - `W5500`_ 10/100 MBPS stand alone Ethernet controller with on-board MAC & PHY
|
| /Zephyr-latest/doc/_scripts/ |
| D | gen_devicetree_rest.py | 65 # vnd A stand-in for a real vendor
67 # Gets split into a key 'vnd' and a value 'A stand-in for a real
222 # but rather a stand-in we use for examples and tests when a real
|
| /Zephyr-latest/soc/nuvoton/npcx/common/ |
| D | power.c | 24 * | Stand-By | Off | Off | Off | Off | Off | Off | On |
|
| /Zephyr-latest/boards/waveshare/esp32s3_touch_lcd_1_28/doc/ |
| D | index.rst | 51 architecture, each core can be enabled to execute customized tasks in stand-alone mode
|
| /Zephyr-latest/boards/others/neorv32/doc/ |
| D | index.rst | 7 ready-to-go auxiliary processor within larger SoC designs or as a stand-alone
|
123
