Home
last modified time | relevance | path

Searched full:over (Results 1 – 25 of 1051) sorted by relevance

12345678910>>...43

/Zephyr-latest/drivers/espi/
DKconfig.xec49 send over eSPI from host.
93 This is the port size used by the Host and EC to communicate over
101 This is the port size used by the Host and EC to communicate over
110 bool "SoC Mailbox over eSPI"
112 Enable a 32 byte mailbox interface accessible via Host I/O over the
116 bool "SoC ACPI EC 2 over eSPI"
118 Enable ACPI EC2 interface accessible via Host I/O over the
122 bool "SoC ACPI EC 3 over eSPI"
124 Enable ACPI EC3 interface accessible via Host I/O over the
128 bool "SoC ACPI EC 4 over eSPI"
[all …]
DKconfig96 Enables UART over eSPI peripheral channel.
101 Enables 8042 keyboard controller over eSPI peripheral channel.
106 Enables ACPI Host I/O over eSPI peripheral channel.
111 Enables ACPI Host I/O over eSPI peripheral channel for private channel.
118 This is the port number used by the Host and EC to communicate over
126 Enables debug Port 80 over eSPI peripheral channel.
137 Enables shared memory region over eSPI peripheral channel to access
145 This is the port number used by the Host and EC to communicate over
155 and so on over eSPI peripheral channel.
162 This is the port number used by the Host and EC to communicate over
[all …]
/Zephyr-latest/include/zephyr/bluetooth/mesh/
Dstatistic.h30 /** Received frames over advertiser. */
32 /** Received frames over loopback. */
34 /** Received frames over proxy. */
36 /** Received over unknown interface. */
38 /** Counter of frames that were initiated to relay over advertiser bearer. */
40 /** Counter of frames that succeeded relaying over advertiser bearer. */
42 /** Counter of frames that were initiated to send over advertiser bearer locally. */
44 /** Counter of frames that succeeded to send over advertiser bearer locally. */
46 /** Counter of frames that were initiated to send over friend bearer. */
48 /** Counter of frames that succeeded to send over friend bearer. */
/Zephyr-latest/tests/drivers/disk/disk_performance/
DREADME.txt11 * Sequential read test: This test performs sequential reads, first only over one
12 sector, than over multiple sequential sectors.
17 * Sequential write test: This test performs sequential writes, first only over
18 one sector, than over multiple sequential sectors.
/Zephyr-latest/samples/subsys/logging/ble_backend/
DREADME.rst5 Send log messages over BLE using the BLE logging backend.
12 with already existing apps to debug BLE connections over UART.
16 to change this configuration to increase the logger throughput over BLE.
29 The BLE logger can be tested with the NRF Toolbox app or any similar app that can connect over
/Zephyr-latest/drivers/serial/
DKconfig.bt5 bool "UART over NUS Bluetooth LE"
12 Enable the UART over NUS Bluetooth driver, which can be used to pipe
13 serial data over Bluetooth LE GATT using NUS (Nordic UART Service).
/Zephyr-latest/dts/bindings/regulator/
Dregulator.yaml143 regulator-over-current-protection:
145 description: Enable over current protection.
150 Set over current protection limit. This is a limit where hardware performs
158 Set over current error limit. This is a limit where part of the hardware
166 Set over current warning limit. This is a limit where hardware is assumed
175 Set over voltage protection limit. This is a limit where hardware performs
183 Set over voltage error limit. This is a limit where part of the hardware
192 Set over voltage warning limit. This is a limit where hardware is assumed
202 Set over under voltage protection limit. This is a limit where hardware
220 Set over under voltage warning limit. This is a limit where hardware is
[all …]
/Zephyr-latest/samples/net/capture/
Doverlay-tunnel.conf8 # Use this for IPv6 over IPv4
12 # Use this for IPv4 over IPv4
/Zephyr-latest/samples/net/sockets/echo_server/
Doverlay-tunnel.conf12 # Use this for IPv6 over IPv4
15 # Use this for IPv4 over IPv4
/Zephyr-latest/subsys/mgmt/mcumgr/transport/
DKconfig.shell18 Enables handling of SMP commands received over shell. This allows
27 Maximum size of SMP frames sent and received over shell. This value
35 Number of buffers used for receiving SMP fragments over shell.
DKconfig.uart19 Enables handling of SMP commands received over UART. This is a
21 commands to be received over UART without requiring an additional
59 Maximum size of SMP frames sent and received over UART, in bytes.
/Zephyr-latest/drivers/sensor/ti/tmp1075/
DKconfig19 bool "Allow interrupts to service over and under temp alerts"
21 This will set up interrupts to service under and over temp alerts
/Zephyr-latest/include/zephyr/drivers/mfd/
Dbd8lb600fs.h36 * function is active, therefore either there is an open load, an over
40 * OCP - over current protection
45 * @param[out] ocp_or_tsd over current protection or thermal shutdown values
/Zephyr-latest/samples/boards/phytec/reel_board/mesh_badge/
DREADME.rst38 #. Once disconnected the board switches over to Bluetooth Mesh mode, and you
39 can't connect to it anymore over GATT.
42 each other over mesh: by pressing the user button on the board the first
47 text, and make it connectable over GATT):
/Zephyr-latest/samples/subsys/lorawan/fuota/
Dsample.yaml2 description: Demonstration of LoRaWAN Firmware Upgrade Over The Air
14 - "<inf> lorawan_fuota: Joining network over OTAA"
DREADME.rst5 Perform a LoRaWAN firmware-upgrade over the air (FUOTA) operation.
10 An application to demonstrate firmware-upgrade over the air (FUOTA) over LoRaWAN.
/Zephyr-latest/dts/bindings/rtc/
Dnxp,pcf8523.yaml44 battery-switch-over:
52 Battery switch-over function selection:
55 - disabled: Battery switch-over disabled - only one power supply (VDD)
/Zephyr-latest/drivers/sensor/ti/tmp108/
DKconfig20 bool "Allow interrupts to service over and under temp alerts"
22 This will set up interrupts to service under and over temp alerts
/Zephyr-latest/arch/arm/core/
Dnmi_on_reset.S15 * rebooting might trigger the exact same problem over and over.
/Zephyr-latest/tests/net/virtual/
Dprj.conf21 # Use this for IPv6 over IPv4|6
24 # Use this for IPv4 over IPv4|6
/Zephyr-latest/dts/arm/st/h7/
Dstm32h743.dtsi65 /* System data RAM accessible over AXI bus: AXI SRAM in D1 domain */
71 /* System data RAM accessible over AHB bus: SRAM1 in D2 domain */
78 /* System data RAM accessible over AHB bus: SRAM2 in D2 domain */
85 /* System data RAM accessible over AHB bus: SRAM3 in D2 domain */
92 /* System data RAM accessible over AHB bus: SRAM4 in D3 domain */
/Zephyr-latest/dts/bindings/iio/afe/
Dcurrent-sense-shunt.yaml5 When an io-channel measures the voltage over a current sense shunt,
7 shunt, not the voltage over it. This binding describes such a current
/Zephyr-latest/include/zephyr/drivers/console/
Duart_mcumgr.h8 * @brief A driver for sending and receiving mcumgr packets over UART.
24 * @brief Contains an mcumgr fragment received over UART.
44 * @brief Sends an mcumgr packet over UART.
/Zephyr-latest/samples/tfm_integration/psa_protected_storage/
DREADME.rst58 Writing data to UID1: The quick brown fox jumps over the lazy dog
64 Data stored in UID1: The quick brown fox jumps over the lazy dog
66 Writing data to UID2 with overwrite protection: The quick brown fox jumps over the lazy dog
67 Attempting to write 'The quick brown fox jumps over the lazy dog' to UID2
/Zephyr-latest/doc/services/storage/fcb/
Dfcb.rst13 recommended over FCB for use as a back-end for the :ref:`settings API
20 the entry, and checksum over the entry contents.
28 exhausted. You have control over what happens next; either erase oldest
35 writing entry to flash completed ok. It will skip over entries which

12345678910>>...43