Searched full:controlled (Results 1 – 25 of 256) sorted by relevance
1234567891011
| /Zephyr-latest/drivers/regulator/ |
| D | Kconfig.gpio | 5 bool "GPIO-controlled regulators"
10 Enable the driver for GPIO-controlled regulators
|
| D | Kconfig.fixed | 5 bool "GPIO-controlled regulators"
10 Enable the driver for GPIO-controlled regulators
|
| /Zephyr-latest/drivers/can/transceiver/ |
| D | Kconfig | 15 bool "GPIO controlled CAN transceiver"
20 Enable support for GPIO controlled CAN transceivers.
|
| /Zephyr-latest/include/zephyr/drivers/can/ |
| D | transceiver.h | 56 * @note The CAN transceiver is controlled by the CAN controller driver and
57 * should not normally be controlled by the application.
76 * @note The CAN transceiver is controlled by the CAN controller driver and
77 * should not normally be controlled by the application.
|
| /Zephyr-latest/dts/bindings/display/ |
| D | nordic,nrf-led-matrix.yaml | 41 - pixel (0,0) is controlled by row 0 and column 0
42 - pixel (1,0) is controlled by row 1 and column 3
43 - pixel (0,1) is controlled by row 2 and column 3
44 - pixel (1,1) is controlled by row 2 and column 4
|
| /Zephyr-latest/dts/bindings/spi/ |
| D | nxp,s32-spi.yaml | 45 This value will not be applied for CS lines controlled by GPIO.
55 This value will not be applied for CS lines controlled by GPIO.
66 This value will not be applied for CS lines controlled by GPIO.
|
| /Zephyr-latest/dts/bindings/regulator/ |
| D | nordic,npm1300-regulator.yaml | 76 Regulator enable controlled by specified regulator GPIO pin.
82 Regulator enable controlled by specified regulator GPIO pin.
88 Retention mode controlled by specified regulator GPIO pin.
|
| D | nordic,npm1100.yaml | 18 Note that only mode can be controlled (via GPIO pin MODE).
|
| /Zephyr-latest/dts/bindings/dac/ |
| D | espressif,esp32-dac.yaml | 7 peripherals set. RTC peripherals has GPIOs controlled by the
41 it does not need to be controlled by the pinctrl node.
|
| /Zephyr-latest/doc/connectivity/bluetooth/api/mesh/ |
| D | proxy.rst | 8 option is set. The Proxy feature state is controlled by the :ref:`bluetooth_mesh_models_cfg_srv`,
12 which is controlled by the :ref:`bluetooth_mesh_models_cfg_cli`.
20 advertise with Private Network Identity and Private Node Identity types, which is controlled by the
|
| /Zephyr-latest/dts/bindings/pinctrl/ |
| D | quicklogic,eos-s3-pinctrl.yaml | 66 It's either controlled from registers of the A0 always-on domain,
67 fabric-controlled for signaling with FPGA,
|
| /Zephyr-latest/soc/atmel/sam/same70/ |
| D | soc_config.c | 25 /* Disable ERASE function on PB12 pin, this is controlled in atmel_same70_config()
36 /* Disable TDI function on PB4 pin, this is controlled by Bus Matrix */ in atmel_same70_config()
|
| /Zephyr-latest/soc/atmel/sam/samv71/ |
| D | soc_config.c | 25 /* Disable ERASE function on PB12 pin, this is controlled in atmel_samv71_config()
36 /* Disable TDI function on PB4 pin, this is controlled by Bus Matrix in atmel_samv71_config()
|
| /Zephyr-latest/share/sysbuild/image_configurations/ |
| D | ALL_image_default.cmake | 5 # This sysbuild CMake file sets the sysbuild controlled settings as properties
|
| /Zephyr-latest/drivers/led/ |
| D | Kconfig.is31fl3216a | 11 IS31FL3216A. This chip supports up to 16 PWM controlled LEDs.
|
| /Zephyr-latest/boards/arduino/opta/dts/bindings/ |
| D | gpio-power-switches.yaml | 6 or other kinds of power switches controlled by a GPIO. Each power
|
| /Zephyr-latest/boards/nxp/imx93_evk/dts/bindings/ |
| D | imx93evk-exp-sel.yaml | 6 functions. They are controlled by EXP_SEL signal from gpio_exp0, an
|
| /Zephyr-latest/boards/shields/nrf7002ek/boards/ |
| D | nrf5340dk_nrf5340_cpuapp.overlay | 7 * same pins as bucken and iovdd-ctrl, we need these pins to be controlled by
|
| /Zephyr-latest/samples/basic/hash_map/ |
| D | Kconfig | 17 size is controlled via
|
| /Zephyr-latest/tests/lib/hash_map/ |
| D | Kconfig | 17 size is controlled via
|
| /Zephyr-latest/dts/bindings/led/ |
| D | nordic,npm1300-led.yaml | 9 or be controlled by software.
|
| /Zephyr-latest/dts/bindings/phy/ |
| D | can-transceiver-gpio.yaml | 4 description: Simple GPIO controlled CAN transceiver
|
| /Zephyr-latest/include/zephyr/dt-bindings/flash_controller/ |
| D | npcx_fiu_qspi.h | 11 /* Software controlled Chip-Select number for UMA transactions */
|
| /Zephyr-latest/include/zephyr/drivers/misc/ |
| D | README | 16 rendering. These operations are controlled by a vendor-specific API designed
|
| /Zephyr-latest/dts/bindings/power-domain/ |
| D | power-domain-gpio.yaml | 4 description: Simple GPIO controlled power domain
|
1234567891011
