Searched full:pa2 (Results 1 – 25 of 109) sorted by relevance
12345
| /Zephyr-latest/samples/boards/st/uart/single_wire/ |
| D | README.rst | 12 board. You need to establish a physical connection between pins PA2 (USART2_TX) and
|
| /Zephyr-latest/boards/google/dragonclaw/doc/ |
| D | index.rst | 22 - USART_2 TX/RX : PA2/PA3
|
| /Zephyr-latest/boards/telink/tlsr9518adk80d/ |
| D | tlsr9518adk80d-pinctrl.dtsi | 51 /* HSPI: CLK(PA2), MOSI(PA4), MISO(PA3) */
|
| /Zephyr-latest/boards/st/nucleo_h755zi_q/ |
| D | nucleo_h755zi_q_stm32h755xx_m7.dts | 13 * Possible pin conflicts: The pins PA2 and PB13 may conflict on selection of
|
| /Zephyr-latest/boards/st/nucleo_h745zi_q/ |
| D | nucleo_h745zi_q_stm32h745xx_m7.dts | 13 * Possible pin conflicts: The pins PA2 and PB13 may conflict on selection of
|
| /Zephyr-latest/boards/others/black_f407zg_pro/doc/ |
| D | index.rst | 129 - UART_2_TX : PA2
160 it to UART2 pins (PA2/PA3).
|
| /Zephyr-latest/boards/gd/gd32l233r_eval/doc/ |
| D | index.rst | 71 is USART1 with TX connected at PA2 and RX at PA3. USART1 have connect to a
|
| /Zephyr-latest/boards/st/stm32f4_disco/doc/ |
| D | index.rst | 118 - UART_2_TX : PA2
145 enable console output you should use a serial cable and connect it to UART2 pins (PA2/PA3).
|
| /Zephyr-latest/boards/sipeed/longan_nano/ |
| D | longan_nano-common.dtsi | 53 /* NOTE: bridge TIMER1_CH2 and LED_BLUE (PA2) */
|
| /Zephyr-latest/boards/st/stm32vl_disco/doc/ |
| D | index.rst | 98 - UART_2_TX : PA2
|
| /Zephyr-latest/boards/st/st25dv_mb1283_disco/doc/ |
| D | index.rst | 59 - UART_2 TX/RX : PA2/PA3 (Available on J6 connector)
|
| /Zephyr-latest/boards/st/stm32l1_disco/doc/ |
| D | index.rst | 114 - UART_2_TX : PA2
|
| /Zephyr-latest/boards/st/nucleo_h753zi/ |
| D | nucleo_h753zi.dts | 170 * The pins PA2 and PB13 may conflict on selection of ETH_STM32_HAL,
|
| /Zephyr-latest/boards/ronoth/lodev/ |
| D | ronoth_lodev.dts | 85 <4 0 &gpioa 2 0>, /* PA2 */
|
| /Zephyr-latest/boards/st/nucleo_h743zi/ |
| D | nucleo_h743zi.dts | 191 * The pins PA2 and PB13 may conflict on selection of ETH_STM32_HAL,
|
| /Zephyr-latest/boards/ronoth/lodev/doc/ |
| D | index.rst | 97 5 PA2
|
| D | s76s.rst | 79 16 PA2\_TxD\_A 47 PA9\_USART1\_TX
110 PA2 I/O FT - TIM21_CH1, LCD_SEG1, TIM2_CH3, TSC_G1_IO3, USART2_TX, LPUART1_…
|
| /Zephyr-latest/boards/st/stm32f0_disco/doc/ |
| D | index.rst | 82 - UART_2_TX : PA2
|
| /Zephyr-latest/boards/dragino/lsn50/doc/ |
| D | index.rst | 116 - UART_2_TX : PA2
|
| /Zephyr-latest/boards/dragino/nbsn95/doc/ |
| D | index.rst | 115 - UART_2_TX : PA2
|
| /Zephyr-latest/boards/st/nucleo_f031k6/doc/ |
| D | index.rst | 88 - UART_1 TX/RX : PA2/PA15 (ST-Link Virtual COM Port)
|
| /Zephyr-latest/boards/st/nucleo_f042k6/doc/ |
| D | index.rst | 88 - UART_1 TX/RX : PA2/PA15 (ST-Link Virtual COM Port)
|
| /Zephyr-latest/boards/st/nucleo_f303k8/doc/ |
| D | index.rst | 112 - UART_2 TX/RX : PA2/PA15 (ST-Link Virtual Port Com)
|
| /Zephyr-latest/boards/st/nucleo_f303re/doc/ |
| D | index.rst | 116 - UART_2 TX/RX : PA2/PA3 (ST-Link Virtual Port Com)
|
| /Zephyr-latest/boards/st/nucleo_g031k8/doc/ |
| D | index.rst | 96 - UART_2 TX/RX : PA2/PA3 (ST-Link Virtual Port Com)
|
12345
