Searched full:hs200 (Results 1 – 13 of 13) sorted by relevance
| /Zephyr-latest/dts/bindings/sdhc/ |
| D | sdhc.yaml | 53 mmc-hs200-1_8v:
56 The host controller supports HS200 at 1.8V
|
| /Zephyr-latest/boards/renesas/rcar_salvator_xs/ |
| D | rcar_salvator_xs.dts | 53 mmc-hs200-1_8v;
|
| /Zephyr-latest/boards/renesas/rcar_spider_s4/ |
| D | rcar_spider_s4_r8a779f0_a55.dts | 48 mmc-hs200-1_8v;
|
| /Zephyr-latest/boards/renesas/rcar_h3ulcb/ |
| D | rcar_h3ulcb_r8a77951_a57.dts | 101 mmc-hs200-1_8v;
|
| /Zephyr-latest/drivers/sdhc/ |
| D | sdhc_esp32.h | 62 "SDR104", "DDR50", "DDR52", "HS200", "HS400"};
|
| D | rcar_mmc.c | 1005 [SDHC_TIMING_HS200] = "HS200", in rcar_mmc_get_timing_str()
1351 LOG_ERR("SDHC I/O: HS200 timing isn't supported"); in rcar_mmc_set_timings()
1560 /* JESD84-B51, 6.6.5.1 Sampling Tuning Sequence for HS200 */
1603 * MMC cards require signal tuning for UHS modes SDR104, HS200 or HS400.
1639 LOG_ERR("%s: tuning isn't possible in HS400 mode, it should be done in HS200", in rcar_mmc_execute_tuning()
1666 /* enable modes SDR104/HS200/HS400 */ in rcar_mmc_execute_tuning()
2075 /* disable sampling clock controller, it is used for uhs/sdr104, hs200 and hs400 */ in rcar_mmc_init_controller_regs()
|
| /Zephyr-latest/tests/subsys/sd/mmc/src/ |
| D | main.c | 198 TC_PRINT("Card timing: MMC HS200\n"); in ZTEST()
|
| /Zephyr-latest/include/zephyr/drivers/ |
| D | sdhc.h | 134 /*!< HS200 mode */
199 unsigned int hs200_support: 1; /**< HS200 support */
|
| /Zephyr-latest/subsys/sd/ |
| D | mmc.c | 513 /* Execute Tuning for HS200 */ in mmc_set_timing()
529 LOG_ERR("Switching MMC back to HS from HS200 during HS400 init failed."); in mmc_set_timing()
|
| /Zephyr-latest/dts/x86/intel/ |
| D | alder_lake.dtsi | 354 mmc-hs200-1_8v;
|
| /Zephyr-latest/include/zephyr/sd/ |
| D | sd_spec.h | 440 MMC_CLOCK_HS400 = MHZ(200), /* Same clock freq as HS200, just DDR */
686 /** Power class information for HS200 at VCC!=1.95V [237] */
|
| /Zephyr-latest/boards/nxp/mimxrt595_evk/ |
| D | mimxrt595_evk_mimxrt595s_cm33.dts | 379 mmc-hs200-1_8v;
|
| /Zephyr-latest/doc/releases/ |
| D | release-notes-3.3.rst | 892 - Support HS400 and HS200 mode. This mode is used with eMMC devices,
1714 - new property: ``mmc-hs200-1_8v``
1719 - new property: ``mmc-hs200-1_8v``
|
