Searched refs:SW3 (Results 1 – 25 of 26) sorted by relevance
12
| /Linux-v5.4/Documentation/devicetree/bindings/regulator/ |
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
97 SW3 {
|
| /Linux-v5.4/Documentation/hid/ |
| D | hid-alps.rst | 114 1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
164 Byte1 1 1 1 0 1 SW3 SW2 SW1
173 SW1-SW3:
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | armada-388-clearfog-base.dts | 23 /* The rear SW3 button */
|
| D | pm9g45.dts | 179 label = "SW3";
|
| D | armada-388-clearfog.dts | 39 /* The rear SW3 button */
|
| D | imx53-qsrb.dts | 59 regulator-name = "SW3";
|
| D | r7s72100-rskrza1.dts | 58 label = "SW3";
|
| D | r7s9210-rza2mevb.dts | 40 label = "SW3";
|
| D | r8a7740-armadillo800eva.dts | 84 label = "SW3";
|
| D | r8a7792-wheat.dts | 69 label = "SW3";
|
| D | imx28-eukrea-mbmx28lc.dtsi | 28 label = "SW3";
|
| D | sh73a0-kzm9g.dts | 110 label = "SW3";
|
| /Linux-v5.4/Documentation/devicetree/bindings/mfd/ |
| D | mc13xxx.txt | 59 sw3 : regulator SW3 (register 29, bit 20)
88 sw3 : regulator SW3 (register 26, bit 0)
|
| /Linux-v5.4/include/linux/mfd/ |
| D | ezx-pcap.h | 132 #define SW3 19 macro
|
| /Linux-v5.4/drivers/regulator/ |
| D | cpcap-regulator.c | 344 CPCAP_REG(SW3, CPCAP_REG_S3C, CPCAP_REG_ASSIGN2,
420 CPCAP_REG(SW3, CPCAP_REG_S3C, CPCAP_REG_ASSIGN2,
|
| D | pcap-regulator.c | 138 VREG_INFO(SW3, PCAP_REG_SWCTRL, 11, 12, 24, NA),
|
| D | pfuze100-regulator.c | 397 PFUZE3000_SW3_REG(PFUZE3000, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
412 PFUZE3000_SW3_REG(PFUZE3001, SW3, PFUZE100_SW3AVOL, 900000, 1650000, 50000),
|
| D | pv88060-regulator.c | 219 PV88060_SW(PV88060, SW3, 5000000),
|
| D | ltc3676.c | 227 LTC3676_LINEAR_REG(SW3, sw3, BUCK3, DVB3A),
|
| D | mc13783-regulator.c | 253 MC13783_DEFINE_SW(SW3, sw3, SWITCHERS5, SWITCHERS5, mc13783_sw3_val),
|
| D | ltc3589.c | 255 LTC3589_LINEAR_REG(SW3, sw3, B3DTV1),
|
| D | mc13892-regulator.c | 269 MC13892_SW_DEFINE(SW3, sw3, SWITCHERS2, SWITCHERS2, mc13892_sw),
|
| /Linux-v5.4/Documentation/networking/ |
| D | arcnet-hardware.txt | 804 SW3 1-8: Node ID Select
820 The eight switches in group SW3 are used to set the node ID. Each node
1942 SW3 1-5: IRQ Select
1952 The eight switches in SW3 are used to set the node ID. Each node attached
2013 *) To enable the Boot ROM set the switch 8 of switch block SW3 to position ON.
2021 Switches 1-5 of the switch block SW3 control the IRQ level.
2036 The switches 6-7 of the switch block SW3 are used to determine the timeout
2772 | SW3 | || | |
2791 SW3 1-5: IRQ Select
2797 Although the jumpers SW1 and SW3 are marked SW, not JP, they are jumpers, not
[all …]
|
| D | ltpc.txt | 78 SW3 IRQ 9 (2 in original card documentation only applies to XT)
|
| /Linux-v5.4/arch/arm64/boot/dts/renesas/ |
| D | ulcb.dtsi | 58 label = "SW3";
|
12
