| /Linux-v4.19/drivers/video/fbdev/omap/ |
| D | lcd_h3.c | 36 r = tps65010_set_gpio_out_value(GPIO1, HIGH); in h3_panel_enable()
38 r = tps65010_set_gpio_out_value(GPIO2, HIGH); in h3_panel_enable()
|
| /Linux-v4.19/Documentation/devicetree/bindings/media/i2c/ |
| D | tvp5150.txt | 21 - hsync-active: active state of the HSYNC signal. Must be <1> (HIGH).
22 - vsync-active: active state of the VSYNC signal. Must be <1> (HIGH).
|
| D | ov7670.txt | 13 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
14 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | ov5640.txt | 38 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
39 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| /Linux-v4.19/Documentation/devicetree/bindings/media/ |
| D | renesas,ceu.txt | 25 - hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
27 - vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | video-interfaces.txt | 111 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
112 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
122 LOW/HIGH respectively.
|
| /Linux-v4.19/include/linux/mfd/ |
| D | tps65010.h | 122 #define HIGH 1 macro
|
| /Linux-v4.19/Documentation/devicetree/bindings/clock/ |
| D | silabs,si5351.txt | 55 1 = clock output is driven HIGH when disabled
56 2 = clock output is FLOATING (HIGH-Z) when disabled
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | rk3228-evb.dts | 63 rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
|
| D | rk3288-rock2-som.dtsi | 251 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /Linux-v4.19/drivers/s390/crypto/ |
| D | zcrypt_msgtype6.h | 114 #define HIGH 500 macro
|
| /Linux-v4.19/drivers/usb/host/ |
| D | ohci-omap.c | 61 #define HIGH 1 macro
110 tps65010_set_gpio_out_value(GPIO1, HIGH); in omap_ohci_transceiver_power()
|
| /Linux-v4.19/Documentation/devicetree/bindings/regulator/ |
| D | gpio-regulator.txt | 13 - gpios-states : gpios pin's initial states array. 0: LOW, 1: HIGH.
|
| D | max8973-regulator.txt | 21 1 for HIGH and 0 for LOW.
|
| /Linux-v4.19/Documentation/media/uapi/cec/ |
| D | cec-ioc-dqevent.rst | 157 * .. _`CEC-EVENT-PIN-CEC-HIGH`:
173 * .. _`CEC-EVENT-PIN-HPD-HIGH`:
191 * .. _`CEC-EVENT-PIN-5V-HIGH`:
|
| /Linux-v4.19/Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 115 GPIO1/nRST_IO pins are HIGH only if all rails
116 that have POK control enabled are HIGH.
|
| D | tps6507x.txt | 30 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH.
|
| /Linux-v4.19/Documentation/devicetree/bindings/thermal/ |
| D | rockchip-thermal.txt | 32 1:HIGH.
|
| /Linux-v4.19/drivers/nfc/st95hf/ |
| D | core.c | 88 #define HIGH 1 macro
466 gpio_set_value(st95con->enable_gpio, HIGH); in st95hf_send_st95enable_negativepulse()
478 gpio_set_value(st95con->enable_gpio, HIGH); in st95hf_send_st95enable_negativepulse()
|
| /Linux-v4.19/arch/arm64/boot/dts/rockchip/ |
| D | rk3368-evb.dtsi | 222 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /Linux-v4.19/Documentation/leds/ |
| D | leds-lm3556.txt | 20 or by pulling the STROBE pin HIGH.
|
| /Linux-v4.19/drivers/net/ieee802154/ |
| D | cc2520.c | 31 #define HIGH 1 macro
1178 gpio_set_value(pdata.vreg, HIGH); in cc2520_probe()
1181 gpio_set_value(pdata.reset, HIGH); in cc2520_probe()
|
| /Linux-v4.19/arch/arm/mach-omap1/ |
| D | board-osk.c | 204 tps65010_set_gpio_out_value(GPIO2, HIGH); in osk_tps_setup()
|
| /Linux-v4.19/Documentation/driver-api/iio/ |
| D | buffers.rst | 60 |D11|D10|D9 |D8 |D7 |D6 |D5 |D4 | (HIGH byte, address 0x07)
|
| /Linux-v4.19/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-max77620.txt | 66 master FPS input event set to HIGH.
|
