Home
last modified time | relevance | path

Searched +full:0 +full:x40000 (Results 1 – 25 of 688) sorted by relevance

12345678910>>...28

/Linux-v5.10/drivers/crypto/cavium/nitrox/
Dnitrox_csr.h21 #define EMU_BIST_STATUSX(_i) (0x1402700 + ((_i) * 0x40000))
22 #define UCD_BIST_STATUS 0x12C0070
23 #define NPS_CORE_BIST_REG 0x10000E8
24 #define NPS_CORE_NPC_BIST_REG 0x1000128
25 #define NPS_PKT_SLC_BIST_REG 0x1040088
26 #define NPS_PKT_IN_BIST_REG 0x1040100
27 #define POM_BIST_REG 0x11C0100
28 #define BMI_BIST_REG 0x1140080
29 #define EFL_CORE_BIST_REGX(_i) (0x1240100 + ((_i) * 0x400))
30 #define EFL_TOP_BIST_STAT 0x1241090
[all …]
/Linux-v5.10/arch/arm/boot/dts/
Dat91sam9x5cm.dtsi11 reg = <0x20000000 0x8000000>;
27 timer@0 {
29 reg = <0>;
40 pinctrl_1wire_cm: 1wire_cm-0 {
52 pinctrl-0 = <&pinctrl_ebi_addr_nand
59 pinctrl-0 = <&pinctrl_nand_oe_we
65 reg = <0x3 0x0 0x800000>;
80 at91bootstrap@0 {
82 reg = <0x0 0x40000>;
87 reg = <0x40000 0xc0000>;
[all …]
Daks-cdu.dts33 rs485-rts-delay = <0 0>;
39 rs485-rts-delay = <0 0>;
45 rs485-rts-delay = <0 0>;
68 bootstrap@0 {
70 reg = <0x0 0x40000>;
75 reg = <0x40000 0x80000>;
80 reg = <0xc0000 0x40000>;
85 reg = <0x100000 0x400000>;
90 reg = <0x500000 0x7b00000>;
Dat91-sama5d4_xplained.dts20 reg = <0x20000000 0x20000000>;
42 cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
44 m25p80@0 {
47 reg = <0>;
60 pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
71 pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
75 slot@0 {
76 reg = <0>;
78 cd-gpios = <&pioE 3 0>;
93 cs-gpios = <&pioB 21 0>;
[all …]
Dam335x-guardian.dts22 cpu@0 {
29 reg = <0x80000000 0x10000000>; /* 256 MB */
35 #size-cells = <0>;
37 pinctrl-0 = <&gpio_keys_pins>;
42 gpios = <&gpio2 21 0>;
50 pinctrl-0 = <&leds_pins>;
70 pinctrl-0 = <&lcd_pins_default &lcd_disen_pins>;
84 hsync-active = <0>;
85 vsync-active = <0>;
90 ac-bias-intrpt = <0>;
[all …]
Dat91-sam9x60ek.dts39 #size-cells = <0>;
41 vdd_1v8: fixed-regulator-vdd_1v8@0 {
81 pinctrl-0 = <&pinctrl_key_gpio_default>;
87 linux,code=<0x104>;
118 pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
124 pinctrl-0 = <&pinctrl_can0_rx_tx>;
130 pinctrl-0 = <&pinctrl_can1_rx_tx>;
136 pinctrl-0 = <&pinctrl_classd_default>;
144 pinctrl-0 = <&pinctrl_dbgu>;
150 pinctrl-0 = <&pinctrl_ebi_addr_nand &pinctrl_ebi_data_0_7>;
[all …]
Domap3430-sdp.dts15 reg = <0x80000000 0x10000000>; /* 256 MB */
23 reg = <0x48>;
50 ranges = <0 0 0x10000000 0x08000000>,
51 <1 0 0x28000000 0x1000000>, /* CS1: 16MB for NAND */
52 <2 0 0x20000000 0x1000000>; /* CS2: 16MB for OneNAND */
54 nor@0,0 {
59 reg = <0 0 0x08000000>;
63 gpmc,cs-on-ns = <0>;
84 partition@0 {
86 reg = <0 0x40000>;
[all …]
Dat91-nattis-2-natte-2.dts45 pwms = <&hlcdc_pwm 0 100000 0>;
47 brightness-levels = < 0 1 2 3 4 5 6 7 8 9
63 pinctrl-0 = <&pinctrl_blon>;
101 pinctrl-0 = <&pinctrl_lvds_prlud0 &pinctrl_lvds_hipow0>;
105 #size-cells = <0>;
107 port@0 {
108 reg = <0>;
160 AT91_PINCTRL_OUTPUT_VAL(0))>;
166 AT91_PINCTRL_OUTPUT_VAL(0))>;
172 AT91_PINCTRL_OUTPUT_VAL(0))>;
[all …]
Dat91-tse850-3.dts21 #clock-cells = <0>;
64 io-channels = <&dpot 0>;
71 io-channels = <&dac 0>;
82 #mux-control-cells = <0>;
84 mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
87 idle-state = <0>;
92 io-channels = <&env_det 0>;
150 at91bootstrap@0 {
152 reg = <0x0 0x40000>;
157 reg = <0x40000 0x60000>;
[all …]
Dat91-sama5d27_wlsom1.dtsi39 pinctrl-0 = <&pinctrl_flx1_default>;
45 pinctrl-0 = <&pinctrl_i2c0_default>;
51 dmas = <0>, <0>;
53 pinctrl-0 = <&pinctrl_i2c1_default>;
58 reg = <0x5b>;
60 lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>;
182 pinctrl-0 = <&pinctrl_macb0_default>;
185 ethernet-phy@0 {
186 reg = <0x0>;
190 pinctrl-0 = <&pinctrl_macb0_phy_irq>;
[all …]
Darmada-380.dtsi20 #size-cells = <0>;
23 cpu@0 {
26 reg = <0>;
46 bus-range = <0x00 0xff>;
49 <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
50 0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
51 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
52 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
53 0x82000000 0x1 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
54 0x81000000 0x1 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO */
[all …]
Dkirkwood-98dx4122.dtsi12 bus-range = <0x00 0xff>;
15 <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
16 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
17 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */>;
19 pcie0: pcie@1,0 {
21 assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
22 reg = <0x0800 0 0 0 0>;
26 ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
27 0x81000000 0 0 0x81000000 0x1 0 1 0>;
28 bus-range = <0x00 0xff>;
[all …]
Dmeson6.dtsi14 #size-cells = <0>;
20 reg = <0x200>;
27 reg = <0x201>;
33 reg = <0xd0000000 0x40000>;
36 ranges = <0x0 0xd0000000 0x40000>;
39 clk81: clk@0 {
40 #clock-cells = <0>;
/Linux-v5.10/Documentation/devicetree/bindings/interrupt-controller/
Dopen-pic.txt26 address. The type shall be <u32> and the value shall be 0. As such,
45 0 = low-to-high edge triggered
63 #address-cells = <0>;
68 // Offset address of 0x40000 and size of 0x40000.
69 reg = <0x40000 0x40000>;
/Linux-v5.10/Documentation/devicetree/bindings/net/
Dbrcm,bcm7445-switch-v4.0.txt6 "brcm,bcm7445-switch-v4.0"
7 "brcm,bcm7278-switch-v4.0"
13 - #size-cells: must be 0, see dsa/dsa.txt
73 ranges = <0 0xf0b00000 0x40804>;
75 ethernet_switch@0 {
76 compatible = "brcm,bcm7445-switch-v4.0";
77 #size-cells = <0>;
79 reg = <0x0 0x40000
80 0x40000 0x110
81 0x40340 0x30
[all …]
/Linux-v5.10/arch/powerpc/boot/dts/fsl/
Dpq3-mpic.dtsi2 * PQ3 MPIC device tree stub [ controller @ offset 0x40000 ]
37 #address-cells = <0>;
39 reg = <0x40000 0x40000>;
49 reg = <0x41100 0x100 0x41300 4>;
50 interrupts = <0 0 3 0
51 1 0 3 0
52 2 0 3 0
53 3 0 3 0>;
58 reg = <0x41400 0x200>;
60 0xb0 2 0 0
[all …]
Dqoriq-mpic.dtsi2 * QorIQ MPIC device tree stub [ controller @ offset 0x40000 ]
37 #address-cells = <0>;
39 reg = <0x40000 0x40000>;
42 clock-frequency = <0x0>;
47 reg = <0x41100 0x100 0x41300 4>;
48 interrupts = <0 0 3 0
49 1 0 3 0
50 2 0 3 0
51 3 0 3 0>;
56 reg = <0x41600 0x200 0x44140 4>;
[all …]
Dqoriq-mpic4.3.dtsi2 * QorIQ MPIC device tree stub [ controller @ offset 0x40000 ]
37 #address-cells = <0>;
39 reg = <0x40000 0x40000>;
42 clock-frequency = <0x0>;
47 reg = <0x41100 0x100 0x41300 4>;
48 interrupts = <0 0 3 0
49 1 0 3 0
50 2 0 3 0
51 3 0 3 0>;
56 reg = <0x41600 0x200 0x44148 4>;
[all …]
/Linux-v5.10/arch/powerpc/boot/dts/
Dxpedite5301.dts16 boot-bank = <0x0>; /* 0: Primary flash, 1: Secondary flash */
29 #size-cells = <0>;
31 PowerPC,8572@0 {
33 reg = <0x0>;
36 d-cache-size = <0x8000>; // L1, 32K
37 i-cache-size = <0x8000>; // L1, 32K
38 timebase-frequency = <0>;
39 bus-frequency = <0>;
40 clock-frequency = <0>;
46 reg = <0x1>;
[all …]
Dxpedite5370.dts27 #size-cells = <0>;
29 PowerPC,8572@0 {
31 reg = <0x0>;
34 d-cache-size = <0x8000>; // L1, 32K
35 i-cache-size = <0x8000>; // L1, 32K
36 timebase-frequency = <0>;
37 bus-frequency = <0>;
38 clock-frequency = <0>;
44 reg = <0x1>;
47 d-cache-size = <0x8000>; // L1, 32K
[all …]
Dxcalibur1501.dts28 #size-cells = <0>;
30 PowerPC,8572@0 {
32 reg = <0x0>;
35 d-cache-size = <0x8000>; // L1, 32K
36 i-cache-size = <0x8000>; // L1, 32K
37 timebase-frequency = <0>;
38 bus-frequency = <0>;
39 clock-frequency = <0>;
45 reg = <0x1>;
48 d-cache-size = <0x8000>; // L1, 32K
[all …]
Dsocrates.dts27 #size-cells = <0>;
29 PowerPC,8544@0 {
31 reg = <0>;
34 d-cache-size = <0x8000>; // L1, 32K
35 i-cache-size = <0x8000>; // L1, 32K
36 timebase-frequency = <0>;
37 bus-frequency = <0>;
38 clock-frequency = <0>;
45 reg = <0x00000000 0x00000000>; // Filled in by U-Boot
53 ranges = <0x00000000 0xe0000000 0x00100000>;
[all …]
Dxpedite5330.dts16 boot-bank = <0x0>; /* 0: Primary flash, 1: Secondary flash */
30 #size-cells = <0>;
32 pmcslot@0 {
33 cell-index = <0>;
44 #size-cells = <0>;
46 xmcslot@0 {
47 cell-index = <0>;
65 #size-cells = <0>;
67 PowerPC,8572@0 {
69 reg = <0x0>;
[all …]
/Linux-v5.10/Documentation/devicetree/bindings/mtd/
Dgpmc-nor.txt27 typically 0 as this is the start of the chip-select.
42 reg = <0x6e000000 0x1000>;
49 ranges = <0 0 0x10000000 0x08000000>;
51 nor@0,0 {
56 reg = <0 0 0x08000000>;
60 gpmc,cs-on-ns = <0>;
81 partition@0 {
83 reg = <0 0x40000>;
87 reg = <0x40000 0x40000>;
91 reg = <0x80000 0x200000>;
[all …]
/Linux-v5.10/Documentation/devicetree/bindings/sram/
Dsram.yaml143 reg = <0x5c000000 0x40000>; /* 256 KiB SRAM at address 0x5c000000 */
147 ranges = <0 0x5c000000 0x40000>;
150 reg = <0x100 0x50>;
154 reg = <0x1000 0x1000>;
159 reg = <0x20000 0x20000>;
174 reg = <0x02020000 0x54000>;
177 ranges = <0 0x02020000 0x54000>;
179 smp-sram@0 {
181 reg = <0x0 0x1000>;
186 reg = <0x53000 0x1000>;
[all …]

12345678910>>...28