1// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
2/*
3 * Copyright (C) Arrow Electronics 2019 - All Rights Reserved
4 * Author: Botond Kardos <botond.kardos@arroweurope.com>
5 *
6 * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
7 * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
8 */
9
10/dts-v1/;
11
12#include "stm32mp157.dtsi"
13#include "stm32mp15-pinctrl.dtsi"
14#include "stm32mp15xxac-pinctrl.dtsi"
15#include <dt-bindings/clock/stm32mp1-clksrc.h>
16#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
17
18/ {
19	model = "Arrow Electronics STM32MP157A Avenger96 board";
20	compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
21
22	aliases {
23		mmc0 = &sdmmc1;
24		serial0 = &uart4;
25		serial1 = &uart7;
26	};
27
28	chosen {
29		stdout-path = "serial0:115200n8";
30	};
31
32	memory@c0000000 {
33		device_type = "memory";
34		reg = <0xc0000000 0x40000000>;
35	};
36};
37
38&i2c4 {
39	pinctrl-names = "default";
40	pinctrl-0 = <&i2c4_pins_a>;
41	i2c-scl-rising-time-ns = <185>;
42	i2c-scl-falling-time-ns = <20>;
43	status = "okay";
44
45	pmic: stpmic@33 {
46		compatible = "st,stpmic1";
47		reg = <0x33>;
48		interrupts-extended = <&exti_pwr 55 IRQ_TYPE_EDGE_FALLING>;
49		interrupt-controller;
50		#interrupt-cells = <2>;
51		status = "okay";
52
53		st,main-control-register = <0x04>;
54		st,vin-control-register = <0xc0>;
55		st,usb-control-register = <0x30>;
56
57		regulators {
58			compatible = "st,stpmic1-regulators";
59			ldo1-supply = <&v3v3>;
60			ldo2-supply = <&v3v3>;
61			ldo3-supply = <&vdd_ddr>;
62			ldo5-supply = <&v3v3>;
63			ldo6-supply = <&v3v3>;
64			pwr_sw1-supply = <&bst_out>;
65			pwr_sw2-supply = <&bst_out>;
66
67			vddcore: buck1 {
68				regulator-name = "vddcore";
69				regulator-min-microvolt = <1200000>;
70				regulator-max-microvolt = <1350000>;
71				regulator-always-on;
72				regulator-initial-mode = <0>;
73				regulator-over-current-protection;
74			};
75
76			vdd_ddr: buck2 {
77				regulator-name = "vdd_ddr";
78				regulator-min-microvolt = <1350000>;
79				regulator-max-microvolt = <1350000>;
80				regulator-always-on;
81				regulator-initial-mode = <0>;
82				regulator-over-current-protection;
83			};
84
85			vdd: buck3 {
86				regulator-name = "vdd";
87				regulator-min-microvolt = <3300000>;
88				regulator-max-microvolt = <3300000>;
89				regulator-always-on;
90				st,mask-reset;
91				regulator-initial-mode = <0>;
92				regulator-over-current-protection;
93			};
94
95			v3v3: buck4 {
96				regulator-name = "v3v3";
97				regulator-min-microvolt = <3300000>;
98				regulator-max-microvolt = <3300000>;
99				regulator-always-on;
100				regulator-over-current-protection;
101				regulator-initial-mode = <0>;
102			};
103
104			vdda: ldo1 {
105				regulator-name = "vdda";
106				regulator-min-microvolt = <2900000>;
107				regulator-max-microvolt = <2900000>;
108			};
109
110			v2v8: ldo2 {
111				regulator-name = "v2v8";
112				regulator-min-microvolt = <2800000>;
113				regulator-max-microvolt = <2800000>;
114			};
115
116			vtt_ddr: ldo3 {
117				regulator-name = "vtt_ddr";
118				regulator-always-on;
119				regulator-over-current-protection;
120				st,regulator-sink-source;
121			};
122
123			vdd_usb: ldo4 {
124				regulator-name = "vdd_usb";
125				regulator-min-microvolt = <3300000>;
126				regulator-max-microvolt = <3300000>;
127			};
128
129			vdd_sd: ldo5 {
130				regulator-name = "vdd_sd";
131				regulator-min-microvolt = <2900000>;
132				regulator-max-microvolt = <2900000>;
133				regulator-boot-on;
134			};
135
136			v1v8: ldo6 {
137				regulator-name = "v1v8";
138				regulator-min-microvolt = <1800000>;
139				regulator-max-microvolt = <1800000>;
140			};
141
142			vref_ddr: vref_ddr {
143				regulator-name = "vref_ddr";
144				regulator-always-on;
145			};
146
147			bst_out: boost {
148				regulator-name = "bst_out";
149			};
150
151			vbus_otg: pwr_sw1 {
152				regulator-name = "vbus_otg";
153			};
154
155			vbus_sw: pwr_sw2 {
156				regulator-name = "vbus_sw";
157				regulator-active-discharge = <1>;
158			};
159		};
160	};
161};
162
163&iwdg2 {
164	timeout-sec = <32>;
165	status = "okay";
166	secure-status = "okay";
167};
168
169&pwr_regulators {
170	vdd-supply = <&vdd>;
171	vdd_3v3_usbfs-supply = <&vdd_usb>;
172};
173
174&rcc {
175	secure-status = "disabled";
176	st,clksrc = <
177		CLK_MPU_PLL1P
178		CLK_AXI_PLL2P
179		CLK_MCU_PLL3P
180		CLK_PLL12_HSE
181		CLK_PLL3_HSE
182		CLK_PLL4_HSE
183		CLK_RTC_LSE
184		CLK_MCO1_DISABLED
185		CLK_MCO2_DISABLED
186	>;
187
188	st,clkdiv = <
189		1 /*MPU*/
190		0 /*AXI*/
191		0 /*MCU*/
192		1 /*APB1*/
193		1 /*APB2*/
194		1 /*APB3*/
195		1 /*APB4*/
196		2 /*APB5*/
197		23 /*RTC*/
198		0 /*MCO1*/
199		0 /*MCO2*/
200	>;
201
202	st,pkcs = <
203		CLK_CKPER_HSE
204		CLK_FMC_ACLK
205		CLK_QSPI_ACLK
206		CLK_ETH_DISABLED
207		CLK_SDMMC12_PLL4P
208		CLK_DSI_DSIPLL
209		CLK_STGEN_HSE
210		CLK_USBPHY_HSE
211		CLK_SPI2S1_PLL3Q
212		CLK_SPI2S23_PLL3Q
213		CLK_SPI45_HSI
214		CLK_SPI6_HSI
215		CLK_I2C46_HSI
216		CLK_SDMMC3_PLL4P
217		CLK_USBO_USBPHY
218		CLK_ADC_CKPER
219		CLK_CEC_LSE
220		CLK_I2C12_HSI
221		CLK_I2C35_HSI
222		CLK_UART1_HSI
223		CLK_UART24_HSI
224		CLK_UART35_HSI
225		CLK_UART6_HSI
226		CLK_UART78_HSI
227		CLK_SPDIF_PLL4P
228		CLK_FDCAN_PLL4R
229		CLK_SAI1_PLL3Q
230		CLK_SAI2_PLL3Q
231		CLK_SAI3_PLL3Q
232		CLK_SAI4_PLL3Q
233		CLK_RNG1_LSI
234		CLK_RNG2_LSI
235		CLK_LPTIM1_PCLK1
236		CLK_LPTIM23_PCLK3
237		CLK_LPTIM45_LSE
238	>;
239
240	/* VCO = 1300.0 MHz => P = 650 (CPU) */
241	pll1: st,pll@0 {
242		compatible = "st,stm32mp1-pll";
243		reg = <0>;
244		cfg = <2 80 0 0 0 PQR(1,0,0)>;
245		frac = <0x800>;
246	};
247
248	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
249	pll2: st,pll@1 {
250		compatible = "st,stm32mp1-pll";
251		reg = <1>;
252		cfg = <2 65 1 0 0 PQR(1,1,1)>;
253		frac = <0x1400>;
254	};
255
256	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
257	pll3: st,pll@2 {
258		compatible = "st,stm32mp1-pll";
259		reg = <2>;
260		cfg = <1 33 1 16 36 PQR(1,1,1)>;
261		frac = <0x1a04>;
262	};
263
264	/* VCO = 480.0 MHz => P = 120, Q = 40, R = 96 */
265	pll4: st,pll@3 {
266		compatible = "st,stm32mp1-pll";
267		reg = <3>;
268		cfg = <1 39 3 11 4 PQR(1,1,1)>;
269	};
270};
271
272&rng1 {
273	status = "okay";
274};
275
276&rtc {
277	status = "okay";
278};
279
280&sdmmc1 {
281	pinctrl-names = "default";
282	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
283	st,sig-dir;
284	st,neg-edge;
285	st,use-ckin;
286	bus-width = <4>;
287	vmmc-supply = <&vdd_sd>;
288	status = "okay";
289};
290
291&uart4 {
292	/* On Low speed expansion header */
293	label = "LS-UART1";
294	pinctrl-names = "default";
295	pinctrl-0 = <&uart4_pins_b>;
296	status = "okay";
297};
298
299&uart7 {
300	/* On Low speed expansion header */
301	label = "LS-UART0";
302	pinctrl-names = "default";
303	pinctrl-0 = <&uart7_pins_a>;
304	status = "okay";
305};
306