cc13x2x7_cc26x2x7/driverlib/prcm.h

/******************************************************************************
*  Filename:       prcm.h
*
*  Description:    Defines and prototypes for the PRCM
*
*  Copyright (c) 2015 - 2022, Texas Instruments Incorporated
*  All rights reserved.
*
*  Redistribution and use in source and binary forms, with or without
*  modification, are permitted provided that the following conditions are met:
*
*  1) Redistributions of source code must retain the above copyright notice,
*     this list of conditions and the following disclaimer.
*
*  2) Redistributions in binary form must reproduce the above copyright notice,
*     this list of conditions and the following disclaimer in the documentation
*     and/or other materials provided with the distribution.
*
*  3) Neither the name of the ORGANIZATION nor the names of its contributors may
*     be used to endorse or promote products derived from this software without
*     specific prior written permission.
*
*  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
*  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
*  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
*  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
*  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
*  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
*  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
*  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
*  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
*  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
*  POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************/

//*****************************************************************************
//
//! \addtogroup system_control_group
//! @{
//! \addtogroup prcm_api
//! @{
//
//*****************************************************************************

#ifndef __PRCM_H__
#define __PRCM_H__

//*****************************************************************************
//
// If building with a C++ compiler, make all of the definitions in this header
// have a C binding.
//
//*****************************************************************************
#ifdef __cplusplus
extern "C"
{
#endif

#include <stdbool.h>
#include <stdint.h>
#include "../inc/hw_types.h"
#include "../inc/hw_memmap.h"
#include "../inc/hw_memmap_common.h"
#include "../inc/hw_ints.h"
#include "../inc/hw_prcm.h"
#include "../inc/hw_nvic.h"
#include "../inc/hw_aon_rtc.h"
#include "interrupt.h"
#include "debug.h"
#include "cpu.h"


//*****************************************************************************
//
// Support for DriverLib in ROM:
// This section renames all functions that are not "static inline", so that
// calling these functions will default to implementation in flash. At the end
// of this file a second renaming will change the defaults to implementation in
// ROM for available functions.
//
// To force use of the implementation in flash, e.g. for debugging:
// - Globally: Define DRIVERLIB_NOROM at project level
// - Per function: Use prefix "NOROM_" when calling the function
//
//*****************************************************************************
#if !defined(DOXYGEN)
    #define PRCMInfClockConfigureSet        NOROM_PRCMInfClockConfigureSet
    #define PRCMInfClockConfigureGet        NOROM_PRCMInfClockConfigureGet
    #define PRCMAudioClockConfigSet         NOROM_PRCMAudioClockConfigSet
    #define PRCMAudioClockConfigSetOverride NOROM_PRCMAudioClockConfigSetOverride
    #define PRCMAudioClockInternalSource    NOROM_PRCMAudioClockInternalSource
    #define PRCMAudioClockExternalSource    NOROM_PRCMAudioClockExternalSource
    #define PRCMPowerDomainOn               NOROM_PRCMPowerDomainOn
    #define PRCMPowerDomainOff              NOROM_PRCMPowerDomainOff
    #define PRCMPeripheralRunEnable         NOROM_PRCMPeripheralRunEnable
    #define PRCMPeripheralRunDisable        NOROM_PRCMPeripheralRunDisable
    #define PRCMPeripheralSleepEnable       NOROM_PRCMPeripheralSleepEnable
    #define PRCMPeripheralSleepDisable      NOROM_PRCMPeripheralSleepDisable
    #define PRCMPeripheralDeepSleepEnable   NOROM_PRCMPeripheralDeepSleepEnable
    #define PRCMPeripheralDeepSleepDisable  NOROM_PRCMPeripheralDeepSleepDisable
    #define PRCMPowerDomainsAllOff          NOROM_PRCMPowerDomainsAllOff
    #define PRCMPowerDomainsAllOn           NOROM_PRCMPowerDomainsAllOn
    #define PRCMDeepSleep                   NOROM_PRCMDeepSleep
#endif

//*****************************************************************************
//
// Defines for the different System CPU power modes.
//
//*****************************************************************************
#define PRCM_RUN_MODE           0x00000001
#define PRCM_SLEEP_MODE         0x00000002
#define PRCM_DEEP_SLEEP_MODE    0x00000004

//*****************************************************************************
//
// Defines used for setting the clock division factors
//
//*****************************************************************************
#define PRCM_CLOCK_DIV_1        PRCM_GPTCLKDIV_RATIO_DIV1
#define PRCM_CLOCK_DIV_2        PRCM_GPTCLKDIV_RATIO_DIV2
#define PRCM_CLOCK_DIV_4        PRCM_GPTCLKDIV_RATIO_DIV4
#define PRCM_CLOCK_DIV_8        PRCM_GPTCLKDIV_RATIO_DIV8
#define PRCM_CLOCK_DIV_16       PRCM_GPTCLKDIV_RATIO_DIV16
#define PRCM_CLOCK_DIV_32       PRCM_GPTCLKDIV_RATIO_DIV32
#define PRCM_CLOCK_DIV_64       PRCM_GPTCLKDIV_RATIO_DIV64
#define PRCM_CLOCK_DIV_128      PRCM_GPTCLKDIV_RATIO_DIV128
#define PRCM_CLOCK_DIV_256      PRCM_GPTCLKDIV_RATIO_DIV256

//*****************************************************************************
//
// Defines used for enabling and disabling domains and memories in the MCU
// domain
//
//*****************************************************************************
#define PRCM_DOMAIN_RFCORE      0x00000001  // RF Core domain ID for
                                            // clock/power control.
#define PRCM_DOMAIN_SERIAL      0x00000002  // Serial domain ID for
                                            // clock/power control.
#define PRCM_DOMAIN_PERIPH      0x00000004  // Peripheral domain ID for
                                            // clock/power control.
#define PRCM_DOMAIN_SYSBUS      0x00000008  // Bus domain ID for clock/power
                                            // control.
#define PRCM_DOMAIN_VIMS        0x00000010  // VIMS domain ID for clock/power
                                            // control.
#define PRCM_DOMAIN_VIMS_OFF_NO_WAKEUP                                        \
                                0x00020010  // For function PRCMPowerDomainOff() it is an option to
                                            // select that VIMS power domain shall not power up
                                            // during the next wake up from uLDO (VIMS_MODE=0b10).
#define PRCM_DOMAIN_CPU         0x00000020  // CPU domain ID for clock/power
                                            // control.
#define PRCM_DOMAIN_TIMER       0x00000040  // GPT domain ID for clock
                                            // control.
#define PRCM_DOMAIN_CLKCTRL     0x00000080  // Clock Control domain ID for
                                            // clock/power control.
#define PRCM_DOMAIN_MCU         0x00000100  // Reset control for entire MCU
                                            // domain.
#define PRCM_DOMAIN_POWER_OFF   0x00000002  // The domain is powered off
#define PRCM_DOMAIN_POWER_ON    0x00000001  // The domain is powered on
#define PRCM_DOMAIN_POWER_DOWN_READY                                          \
                                0x00000000  // The domain is ready to be
                                            // powered down.

//*****************************************************************************
//
// Defines for setting up the audio interface in the I2S module.
//
//*****************************************************************************
#define PRCM_WCLK_NEG_EDGE      0x00000008
#define PRCM_WCLK_POS_EDGE      0x00000000
#define PRCM_WCLK_SINGLE_PHASE  0x00000000
#define PRCM_WCLK_DUAL_PHASE    0x00000002
#define PRCM_WCLK_USER_DEF      0x00000004
#define PRCM_I2S_WCLK_NEG_EDGE           0
#define PRCM_I2S_WCLK_POS_EDGE           1
#define PRCM_I2S_WCLK_SINGLE_PHASE       0
#define PRCM_I2S_WCLK_DUAL_PHASE         1
#define PRCM_I2S_WCLK_USER_DEF           2

#define I2S_SAMPLE_RATE_16K     0x00000001
#define I2S_SAMPLE_RATE_24K     0x00000002
#define I2S_SAMPLE_RATE_32K     0x00000004
#define I2S_SAMPLE_RATE_48K     0x00000008

//*****************************************************************************
//
// Defines used for enabling and disabling peripheral modules in the MCU domain
// bits[11:8] Defines the index into the register offset constant tables:
//            g_pui32RCGCRegs, g_pui32SCGCRegs and g_pui32DCGCRegs
// bits[4:0]  Defines the bit position within the register pointet on in [11:8]
//
//*****************************************************************************
#define PRCM_PERIPH_TIMER0 ( 0x00000000 | ( PRCM_GPTCLKGR_CLK_EN_S           )) // Peripheral ID for GPT module 0
#define PRCM_PERIPH_TIMER1 ( 0x00000000 | ( PRCM_GPTCLKGR_CLK_EN_S       + 1 )) // Peripheral ID for GPT module 1
#define PRCM_PERIPH_TIMER2 ( 0x00000000 | ( PRCM_GPTCLKGR_CLK_EN_S       + 2 )) // Peripheral ID for GPT module 2
#define PRCM_PERIPH_TIMER3 ( 0x00000000 | ( PRCM_GPTCLKGR_CLK_EN_S       + 3 )) // Peripheral ID for GPT module 3
#define PRCM_PERIPH_SSI0   ( 0x00000100 | ( PRCM_SSICLKGR_CLK_EN_S           )) // Peripheral ID for SSI module 0
#define PRCM_PERIPH_SSI1   ( 0x00000100 | ( PRCM_SSICLKGR_CLK_EN_S       + 1 )) // Peripheral ID for SSI module 1
#define PRCM_PERIPH_UART0  ( 0x00000200 | ( PRCM_UARTCLKGR_CLK_EN_S          )) // Peripheral ID for UART module 0
#define PRCM_PERIPH_UART1  ( 0x00000200 | ( PRCM_UARTCLKGR_CLK_EN_S      + 1 )) // Peripheral ID for UART module 1
#define PRCM_PERIPH_I2C0   ( 0x00000300 | ( PRCM_I2CCLKGR_CLK_EN_S           )) // Peripheral ID for I2C module 0
#define PRCM_PERIPH_CRYPTO ( 0x00000400 | ( PRCM_SECDMACLKGR_CRYPTO_CLK_EN_S )) // Peripheral ID for CRYPTO module
#define PRCM_PERIPH_TRNG   ( 0x00000400 | ( PRCM_SECDMACLKGR_TRNG_CLK_EN_S   )) // Peripheral ID for TRNG module
#define PRCM_PERIPH_PKA    ( 0x00000400 | ( PRCM_SECDMACLKGR_PKA_CLK_EN_S    )) // Peripheral ID for PKA module
#define PRCM_PERIPH_UDMA   ( 0x00000400 | ( PRCM_SECDMACLKGR_DMA_CLK_EN_S    )) // Peripheral ID for UDMA module
#define PRCM_PERIPH_GPIO   ( 0x00000500 | ( PRCM_GPIOCLKGR_CLK_EN_S          )) // Peripheral ID for GPIO module
#define PRCM_PERIPH_I2S    ( 0x00000600 | ( PRCM_I2SCLKGR_CLK_EN_S           )) // Peripheral ID for I2S module

//*****************************************************************************
//
// API Functions and prototypes
//
//*****************************************************************************

#ifdef DRIVERLIB_DEBUG
//*****************************************************************************
//
//! \brief Checks a peripheral identifier.
//!
//! This function determines if a peripheral identifier is valid.
//!
//! \param ui32Peripheral is the peripheral identifier.
//!
//! \return Returns status of peripheral identifier:
//! - \b true  : Peripheral identifier is valid.
//! - \b false : Peripheral identifier is invalid.
//
//*****************************************************************************
static bool
PRCMPeripheralValid(uint32_t ui32Peripheral)
{
    return((ui32Peripheral == PRCM_PERIPH_TIMER0)   ||
           (ui32Peripheral == PRCM_PERIPH_TIMER1)   ||
           (ui32Peripheral == PRCM_PERIPH_TIMER2)   ||
           (ui32Peripheral == PRCM_PERIPH_TIMER3)   ||
           (ui32Peripheral == PRCM_PERIPH_SSI0)     ||
           (ui32Peripheral == PRCM_PERIPH_UART0)    ||
           (ui32Peripheral == PRCM_PERIPH_SSI1)     ||
           (ui32Peripheral == PRCM_PERIPH_UART1)    ||
           (ui32Peripheral == PRCM_PERIPH_PKA)      ||
           (ui32Peripheral == PRCM_PERIPH_I2C0)     ||
           (ui32Peripheral == PRCM_PERIPH_CRYPTO)   ||
           (ui32Peripheral == PRCM_PERIPH_TRNG)     ||
           (ui32Peripheral == PRCM_PERIPH_UDMA)     ||
           (ui32Peripheral == PRCM_PERIPH_GPIO)     ||
           (ui32Peripheral == PRCM_PERIPH_I2S));
}
#endif

//*****************************************************************************
//
//! \brief Configure the infrastructure clock.
//!
//! Each System CPU power mode has its own infrastructure clock division factor. This
//! function can be used for setting up the division factor for the
//! infrastructure clock in the available power modes for the System CPU. The
//! infrastructure clock is used for all internal logic in the PRCM, and is
//! always running as long as power is on in the MCU voltage domain.
//! This can be enabled and disabled from the AON Wake Up Controller.
//!
//! \note If source clock is 48 MHz, minimum clock divider is \ref PRCM_CLOCK_DIV_2.
//!
//! \param ui32ClkDiv determines the division ratio for the infrastructure
//! clock when the device is in the specified mode.
//! Allowed division factors for all three System CPU power modes are:
//! - \ref PRCM_CLOCK_DIV_1
//! - \ref PRCM_CLOCK_DIV_2
//! - \ref PRCM_CLOCK_DIV_8
//! - \ref PRCM_CLOCK_DIV_32
//! \param ui32PowerMode determines the System CPU operation mode for which to
//! modify the clock division factor.
//! The three allowed power modes are:
//! - \ref PRCM_RUN_MODE
//! - \ref PRCM_SLEEP_MODE
//! - \ref PRCM_DEEP_SLEEP_MODE
//!
//! \return None
//
//*****************************************************************************
extern void PRCMInfClockConfigureSet(uint32_t ui32ClkDiv,
                                     uint32_t ui32PowerMode);

//*****************************************************************************
//
//! \brief Use this function to get the infrastructure clock configuration.
//!
//! \param ui32PowerMode determines which System CPU power mode to return the
//! infrastructure clock division ratio for.
//! The three allowed power modes are:
//! - \ref PRCM_RUN_MODE
//! - \ref PRCM_SLEEP_MODE
//! - \ref PRCM_DEEP_SLEEP_MODE
//!
//! \return Returns the infrastructure clock division factor for the specified
//! power mode.
//! - \ref PRCM_CLOCK_DIV_1
//! - \ref PRCM_CLOCK_DIV_2
//! - \ref PRCM_CLOCK_DIV_8
//! - \ref PRCM_CLOCK_DIV_32
//!
//! \sa \ref PRCMInfClockConfigureSet().
//
//*****************************************************************************
extern uint32_t PRCMInfClockConfigureGet(uint32_t ui32PowerMode);

//*****************************************************************************
//
//! \brief Assert or de-assert a request for the uLDO.
//!
//! Use this function to request to switch to the micro Low Voltage Dropout
//! regulator (uLDO). The uLDO has a much lower capacity for supplying power
//! to the system. It is therefore imperative and solely the programmers
//! responsibility to ensure that a sufficient amount of peripheral modules
//! have been turned of before requesting a switch to the uLDO.
//!
//! \note Asserting this bit has no effect until:
//! 1. FLASH has accepted to be powered down
//! 2. Deepsleep must be asserted
//!
//! \param ui32Enable
//! - 0 : Disable uLDO request
//! - 1 : Enable uLDO request
//!
//! \return None
//!
//! \sa \ref PRCMDeepSleep()
//
//*****************************************************************************
__STATIC_INLINE void
PRCMMcuUldoConfigure(uint32_t ui32Enable)
{
    // Enable or disable the uLDO request signal.
    HWREG(PRCM_BASE + NONSECURE_OFFSET + PRCM_O_VDCTL) = ui32Enable;
}

//*****************************************************************************
//
//! \brief Setup the clock division factor for the GP-Timer domain.
//!
//! Use this function to set up the clock division factor on the GP-Timer.
//!
//! The division rate will be constant and ungated for Run / Sleep / DeepSleep mode when
//! it is slower than PRCM_GPTCLKDIV_RATIO setting.
//! When set faster than PRCM_GPTCLKDIV_RATIO setting PRCM_GPTCLKDIV_RATIO will be used.
//! Note that the register will contain the written content even though the setting is
//! faster than PRCM_GPTCLKDIV_RATIO setting.
//!
//! \note For change to take effect, \ref PRCMLoadSet() needs to be called
//!
//! \param clkDiv is the division factor to set.
//! The argument must be only one of the following values:
//! - \ref PRCM_CLOCK_DIV_1
//! - \ref PRCM_CLOCK_DIV_2
//! - \ref PRCM_CLOCK_DIV_4
//! - \ref PRCM_CLOCK_DIV_8
//! - \ref PRCM_CLOCK_DIV_16
//! - \ref PRCM_CLOCK_DIV_32
//! - \ref PRCM_CLOCK_DIV_64
//! - \ref PRCM_CLOCK_DIV_128
//! - \ref PRCM_CLOCK_DIV_256
//!
//! \return None
//!
//! \sa \ref PRCMGPTimerClockDivisionGet()
//
//*****************************************************************************
__STATIC_INLINE void
PRCMGPTimerClockDivisionSet( uint32_t clkDiv )
{
    ASSERT( clkDiv <= PRCM_GPTCLKDIV_RATIO_DIV256 );

    HWREG( PRCM_BASE + NONSECURE_OFFSET + PRCM_O_GPTCLKDIV ) = clkDiv;
}

//*****************************************************************************
//
//! \brief Get the clock division factor for the GP-Timer domain.
//!
//! Use this function to get the clock division factor set for the GP-Timer.
//!
//! \return Returns one of the following values:
//! - \ref PRCM_CLOCK_DIV_1
//! - \ref PRCM_CLOCK_DIV_2
//! - \ref PRCM_CLOCK_DIV_4
//! - \ref PRCM_CLOCK_DIV_8
//! - \ref PRCM_CLOCK_DIV_16
//! - \ref PRCM_CLOCK_DIV_32
//! - \ref PRCM_CLOCK_DIV_64
//! - \ref PRCM_CLOCK_DIV_128
//! - \ref PRCM_CLOCK_DIV_256
//!
//! \sa \ref PRCMGPTimerClockDivisionSet()
//
//*****************************************************************************
__STATIC_INLINE uint32_t
PRCMGPTimerClockDivisionGet( void )
{
    return ( HWREG( PRCM_BASE + NONSECURE_OFFSET + PRCM_O_GPTCLKDIV ));
}


//*****************************************************************************
//
//! \brief Enable the audio clock generation.
//!
//! Use this function to enable the audio clock generation.
//!
//! \return None
//
//*****************************************************************************
__STATIC_INLINE void
PRCMAudioClockEnable(void)
{
    // Enable the audio clock generation.
    HWREGBITW(PRCM_BASE + PRCM_O_I2SCLKCTL, PRCM_I2SCLKCTL_EN_BITN) = 1;
}

//*****************************************************************************
//
//! \brief Disable the audio clock generation.
//!
//! Use this function to disable the audio clock generation.
//!
//! \return None
//
//*****************************************************************************
__STATIC_INLINE void
PRCMAudioClockDisable(void)
{
    // Disable the audio clock generation
    HWREGBITW(PRCM_BASE + PRCM_O_I2SCLKCTL, PRCM_I2SCLKCTL_EN_BITN) = 0;
}

//*****************************************************************************
//
//! \brief Configure the audio clock generation.
//!
//! \deprecated This function will be removed in a future release.
//!
//! Use this function to set the sample rate when using internal audio clock
//! generation for the I2S module.
//!
//! \note While other clocks are possible, the stability of the four sample
//! rates defined here are only guaranteed if the clock input to the I2S module
//! is 48MHz.
//!
//! \param ui32ClkConfig is the audio clock configuration.
//! The parameter is a bitwise OR'ed value consisting of:
//! - Phase
//!   - \ref PRCM_WCLK_SINGLE_PHASE
//!   - \ref PRCM_WCLK_DUAL_PHASE
//! - Clock polarity
//!   - \ref PRCM_WCLK_NEG_EDGE
//!   - \ref PRCM_WCLK_POS_EDGE
//! \param ui32SampleRate is the desired audio clock sample rate.
//! The supported sample rate configurations are:
//! - \ref I2S_SAMPLE_RATE_16K
//! - \ref I2S_SAMPLE_RATE_24K
//! - \ref I2S_SAMPLE_RATE_32K
//! - \ref I2S_SAMPLE_RATE_48K
//!
//! \return None
//!
//! \sa \ref PRCMAudioClockConfigSetOverride()
//
//*****************************************************************************
#ifndef DEPRECATED
extern void PRCMAudioClockConfigSet(uint32_t ui32ClkConfig,
                                    uint32_t ui32SampleRate);
#endif

//*****************************************************************************
//
//! \brief Configure the audio clock generation with manual setting of clock divider.
//!
//! \deprecated This function will be removed in a future release.
//!
//! Use this function to set the audio clock divider values manually.
//!
//! \note See hardware documentation before setting audio clock dividers manually.
//!
//! \param ui32ClkConfig is the audio clock configuration.
//! The parameter is a bitwise OR'ed value consisting of:
//! - Phase
//!   - \ref PRCM_WCLK_SINGLE_PHASE
//!   - \ref PRCM_WCLK_DUAL_PHASE
//! - Clock polarity
//!   - \ref PRCM_WCLK_NEG_EDGE
//!   - \ref PRCM_WCLK_POS_EDGE
//! \param ui32MstDiv is the desired master clock divider.
//! \param ui32WordDiv is the desired word clock divider.
//! \param ui32BitDiv is the desired bit clock divider.
//!
//! \return None
//!
//! \sa \ref PRCMAudioClockConfigSet()
//
//*****************************************************************************
#ifndef DEPRECATED
extern void PRCMAudioClockConfigSetOverride(uint32_t ui32ClkConfig, uint32_t ui32MstDiv,
                        uint32_t ui32BitDiv, uint32_t ui32WordDiv);
#endif

//*****************************************************************************
//
//! \brief Configure the audio clocks for I2S module.
//!
//! \note See hardware documentation before setting audio clock dividers.
//!       This is user's responsability to provide valid clock dividers.
//!
//! \param ui8SamplingEdge Define the clock polarity:
//!        - \ref PRCM_I2S_WCLK_NEG_EDGE
//!        - \ref PRCM_I2S_WCLK_POS_EDGE
//! \param ui8WCLKPhase Define I2S phase used
//!        - PRCM_I2S_WCLK_SINGLE_PHASE
//!        - PRCM_I2S_WCLK_DUAL_PHASE
//!        - PRCM_I2S_WCLK_USER_DEF
//! \param ui32MstDiv is the desired master clock divider.
//! \param ui32BitDiv is the desired bit clock divider.
//! \param ui32WordDiv is the desired word clock divider.
//!
//! \return None
//!
//*****************************************************************************
extern void PRCMAudioClockConfigOverride
                           (uint8_t  ui8SamplingEdge,
                            uint8_t  ui8WCLKPhase,
                            uint32_t ui32MstDiv,
                            uint32_t ui32BitDiv,
                            uint32_t ui32WordDiv);

//*****************************************************************************
//
//! \brief Configure the audio clocks to be internally generated.
//!
//! Use this function to set the audio clocks as internal.
//!
//! \return None
//!
//! \sa \ref PRCMAudioClockExternalSource()
//
//*****************************************************************************
extern void PRCMAudioClockInternalSource(void);

//*****************************************************************************
//
//! \brief Configure the audio clocks to be externally generated.
//!
//! Use this function to set the audio clocks as external.
//!
//! \return None
//!
//! \sa \ref PRCMAudioClockInternalSource()
//
//*****************************************************************************
extern void PRCMAudioClockExternalSource(void);

//*****************************************************************************
//
//! \brief Use this function to synchronize the load settings.
//!
//! Most of the clock settings in the PRCM module should be updated
//! synchronously. This is ensured by the implementation of a load registers
//! that, when written to, will let the previous written update values for all
//! the relevant registers propagate through to hardware.
//!
//! The functions that require a synchronization of the clock settings are:
//! - \ref PRCMAudioClockConfigSet()
//! - \ref PRCMAudioClockConfigSetOverride()
//! - \ref PRCMAudioClockDisable()
//! - \ref PRCMDomainEnable()
//! - \ref PRCMDomainDisable()
//! - \ref PRCMPeripheralRunEnable()
//! - \ref PRCMPeripheralRunDisable()
//! - \ref PRCMPeripheralSleepEnable()
//! - \ref PRCMPeripheralSleepDisable()
//! - \ref PRCMPeripheralDeepSleepEnable()
//! - \ref PRCMPeripheralDeepSleepDisable()
//!
//! \return None
//!
//! \sa \ref PRCMLoadGet()
//
//*****************************************************************************
__STATIC_INLINE void
PRCMLoadSet(void)
{
    // Enable the update of all load related registers.
    HWREG(PRCM_NONBUF_BASE + PRCM_O_CLKLOADCTL) = PRCM_CLKLOADCTL_LOAD;
}

//*****************************************************************************
//
//! \brief Check if any of the load sensitive register has been updated.
//!
//! \return Returns status of the load sensitive register:
//! - \c true  : No registers have changed since the last load.
//! - \c false : Any register has changed.
//!
//! \sa \ref PRCMLoadSet()
//
//*****************************************************************************
__STATIC_INLINE bool
PRCMLoadGet(void)
{
    // Return the load status.
    return ((HWREG(PRCM_BASE + NONSECURE_OFFSET + PRCM_O_CLKLOADCTL) & PRCM_CLKLOADCTL_LOAD_DONE) ?
            true : false);
}

//*****************************************************************************
//
//! \brief Enable clock domains in the MCU voltage domain.
//!
//! \note A call to this function will only setup the shadow registers in the
//! MCU domain for the PRCM module. For the changes to propagate to the system
//! controller in the AON domain a call to this function should always be
//! followed by a call to \ref PRCMLoadSet().
//!
//! \note Clocks will only be running if the domain is powered.
//!
//! \param ui32Domains is a bit mask containing the clock domains to enable.
//! The independent clock domains inside the MCU voltage domain which can be
//! configured are:
//! - \ref PRCM_DOMAIN_RFCORE
//! - \ref PRCM_DOMAIN_VIMS
//!
//! \return None
//
//*****************************************************************************
__STATIC_INLINE void
PRCMDomainEnable(uint32_t ui32Domains)
{
    // Check the arguments.
    ASSERT((ui32Domains & PRCM_DOMAIN_RFCORE) ||
           (ui32Domains & PRCM_DOMAIN_VIMS));

    // Enable the clock domain(s).
    if(ui32Domains & PRCM_DOMAIN_RFCORE)
    {
        HWREG(PRCM_BASE + NONSECURE_OFFSET + PRCM_O_RFCCLKG) = PRCM_RFCCLKG_CLK_EN;
    }
    if(ui32Domains & PRCM_DOMAIN_VIMS)
    {
        HWREG(PRCM_BASE + NONSECURE_OFFSET + PRCM_O_VIMSCLKG) = PRCM_VIMSCLKG_CLK_EN_M;
    }
}

//*****************************************************************************
//
//! \brief Disable clock domains in the MCU voltage domain.
//!
//! \note A call to this function will only setup the shadow registers in the
//! MCU domain for the PRCM module. For the changes to propagate to the system
//! controller in the AON domain a call to this function should always be
//! followed by a call to \ref PRCMLoadSet().
//!
//! \note Clocks will only be running if the domain is powered.
//!
//! \param ui32Domains is a bit mask containing the clock domains to disable.
//! The independent clock domains inside the MCU voltage domain are:
//! - \ref PRCM_DOMAIN_RFCORE
//! - \ref PRCM_DOMAIN_VIMS
//!
//! \return None
//!
//! \sa PRCMDomainEnable()
//
//*****************************************************************************
__STATIC_INLINE void
PRCMDomainDisable(uint32_t ui32Domains)
{
    // Check the arguments.
    ASSERT((ui32Domains & PRCM_DOMAIN_RFCORE) ||
           (ui32Domains & PRCM_DOMAIN_VIMS));

    // Disable the power domains.
    if(ui32Domains & PRCM_DOMAIN_RFCORE)
    {
        HWREG(PRCM_BASE + NONSECURE_OFFSET + PRCM_O_RFCCLKG) = 0x0;
    }
    if(ui32Domains & PRCM_DOMAIN_VIMS)
    {
        HWREG(PRCM_BASE + NONSECURE_OFFSET + PRCM_O_VIMSCLKG) = 0x0;
    }
}

//*****************************************************************************
//
//! \brief Turn power on in power domains in the MCU domain.
//!
//! Use this function to turn on power domains inside the MCU voltage domain.
//!
//! Power on and power off request has different implications for the
//! different power domains.
//! - RF Core power domain:
//!   - Power On  : Domain is on or in the process of turning on.
//!   - Power Off : Domain is powered down when System CPU is in deep sleep. The third
//!                 option for the RF Core is to power down when the it is idle.
//!                 This can be set using \b PRCMRfPowerDownWhenIdle()
//! - SERIAL power domain:
//!   - Power on  : Domain is powered on.
//!   - Power off : Domain is powered off.
//! - PERIPHERIAL power domain:
//!   - Power on  : Domain is powered on.
//!   - Power off : Domain is powered off.
//! - VIMS power domain:
//!   - Power On  : Domain is powered if Bus domain is powered.
//!   - Power Off : Domain is only powered when CPU domain is on.
//! - BUS power domain:
//!   - Power On  : Domain is on.
//!   - Power Off : Domain is on if requested by RF Core or if CPU domain is on.
//! - CPU power domain:
//!   - Power On  : Domain is on.
//!   - Power Off : Domain is powering down if System CPU is idle. This will also
//!                 initiate a power down of the SRAM and BUS power domains, unless
//!                 RF Core is requesting them to be on.
//!
//! \note After a call to this function the status of the power domain should be checked
//! using either \ref PRCMPowerDomainsAllOff() or \ref PRCMPowerDomainsAllOn().
//! Any write operation to a power domain which is still not operational can
//! result in unexpected behavior.
//!
//! \param ui32Domains determines which power domains to turn on.
//! The domains that can be turned on/off are:
//! - \b PRCM_DOMAIN_RFCORE : RF Core
//! - \b PRCM_DOMAIN_SERIAL : SSI0, UART0, I2C0
//! - \b PRCM_DOMAIN_PERIPH : GPT0, GPT1, GPT2, GPT3, GPIO, SSI1, I2S, DMA, UART1
//! - \b PRCM_DOMAIN_VIMS   : SRAM, FLASH, ROM
//! - \b PRCM_DOMAIN_SYSBUS
//! - \b PRCM_DOMAIN_CPU
//!
//! \return None
//
//*****************************************************************************
extern void PRCMPowerDomainOn(uint32_t ui32Domains);

//*****************************************************************************
//
//! \brief Turn off a specific power domain.
//!
//! Use this function to power down domains inside the MCU voltage domain.
//!
//! \note For specifics regarding on/off configuration please see
//! \ref PRCMPowerDomainOn().
//!
//! \param ui32Domains determines which domain to request a power down for.
//! The domains that can be turned on/off are:
//! - \b PRCM_DOMAIN_RFCORE             : RF Core
//! - \b PRCM_DOMAIN_SERIAL             : SSI0, UART0, I2C0
//! - \b PRCM_DOMAIN_PERIPH             : GPT0, GPT1, GPT2, GPT3, GPIO, SSI1, I2S, DMA, UART1
//! - \b PRCM_DOMAIN_VIMS               : SRAM, FLASH, ROM
//! - \b PRCM_DOMAIN_VIMS_OFF_NO_WAKEUP : SRAM, FLASH, ROM
//! - \b PRCM_DOMAIN_SYSBUS
//! - \b PRCM_DOMAIN_CPU
//!
//! \return None
//
//*****************************************************************************
extern void PRCMPowerDomainOff(uint32_t ui32Domains);

//*****************************************************************************
//
//! \brief Configure RF core to power down when idle.
//!
//! Use this function to configure the RF core to power down when Idle. This
//! is handled automatically in hardware if the RF Core reports that it is
//! idle.
//!
//! \return None
//
//*****************************************************************************
__STATIC_INLINE void
PRCMRfPowerDownWhenIdle(void)
{
    // Configure the RF power domain.
    HWREG(PRCM_BASE + NONSECURE_OFFSET + PRCM_O_PDCTL0RFC) = 0;
}

//*****************************************************************************
//
//! \brief Enables a peripheral in Run mode.
//!
//! Peripherals are enabled with this function.  At power-up, some peripherals
//! are disabled; they must be enabled in order to operate or respond to
//! register reads/writes.
//!
//! \note The actual enabling of the peripheral may be delayed until some
//! time after this function returns. Care should be taken to ensure that the
//! peripheral is not accessed until it is enabled.
//! When enabling Timers always make sure that the division factor for the
//! \b PERBUSCPUCLK is set. This will guarantee that the timers run at a
//! continuous rate even if the \b SYSBUSCLK is gated.
//!
//! \note A call to this function will only setup the shadow registers in the
//! MCU domain for the PRCM module. For the changes to propagate to the system
//! controller in the AON domain a call to this function should always be
//! followed by a call to \ref PRCMLoadSet().
//!
//! \param ui32Peripheral is the peripheral to enable.
//! The parameter must be one of the following:
//! - \ref PRCM_PERIPH_TIMER0
//! - \ref PRCM_PERIPH_TIMER1
//! - \ref PRCM_PERIPH_TIMER2
//! - \ref PRCM_PERIPH_TIMER3
//! - \ref PRCM_PERIPH_SSI0
//! - \ref PRCM_PERIPH_SSI1
//! - \ref PRCM_PERIPH_UART0
//! - \ref PRCM_PERIPH_UART1
//! - \ref PRCM_PERIPH_I2C0
//! - \ref PRCM_PERIPH_CRYPTO
//! - \ref PRCM_PERIPH_TRNG
//! - \ref PRCM_PERIPH_PKA
//! - \ref PRCM_PERIPH_UDMA
//! - \ref PRCM_PERIPH_GPIO
//! - \ref PRCM_PERIPH_I2S
//!
//! \return None
//!
//! \sa \ref PRCMLoadSet()
//
//*****************************************************************************
extern void PRCMPeripheralRunEnable(uint32_t ui32Peripheral);

//*****************************************************************************
//
//! \brief Disables a peripheral in Run mode
//!
//! Peripherals are disabled with this function. Once disabled, they will not
//! operate or respond to register reads/writes.
//!
//! \note A call to this function will only setup the shadow registers in the
//! MCU domain for the PRCM module. For the changes to propagate to the system
//! controller in the AON domain a call to this function should always be
//! followed by a call to \ref PRCMLoadSet().
//!
//! \note The actual disabling of the peripheral may be delayed until some
//! time after this function returns. Care should be taken by the user to
//! ensure that the peripheral is not accessed in this interval as this might
//! cause the system to hang.
//!
//! \param ui32Peripheral is the peripheral to disable.
//! The parameter must be one of the following:
//! - \ref PRCM_PERIPH_TIMER0
//! - \ref PRCM_PERIPH_TIMER1
//! - \ref PRCM_PERIPH_TIMER2
//! - \ref PRCM_PERIPH_TIMER3
//! - \ref PRCM_PERIPH_SSI0
//! - \ref PRCM_PERIPH_SSI1
//! - \ref PRCM_PERIPH_UART0
//! - \ref PRCM_PERIPH_UART1
//! - \ref PRCM_PERIPH_I2C0
//! - \ref PRCM_PERIPH_CRYPTO
//! - \ref PRCM_PERIPH_TRNG
//! - \ref PRCM_PERIPH_PKA
//! - \ref PRCM_PERIPH_UDMA
//! - \ref PRCM_PERIPH_GPIO
//! - \ref PRCM_PERIPH_I2S
//!
//! \return None
//!
//! \sa \ref PRCMLoadSet()
//
//*****************************************************************************
extern void PRCMPeripheralRunDisable(uint32_t ui32Peripheral);

//*****************************************************************************
//
//! \brief Enables a peripheral in sleep mode.
//!
//! This function allows a peripheral to continue operating when the processor
//! goes into sleep mode. Since the clocking configuration of the device does
//! not change, any peripheral can safely continue operating while the
//! processor is in sleep mode, and can therefore wake the processor from sleep
//! mode.
//!
//! \note A call to this function will only setup the shadow registers in the
//! MCU domain for the PRCM module. For the changes to propagate to the system
//! controller in the AON domain a call to this function should always be
//! followed by a call to \ref PRCMLoadSet().
//!
//! \param ui32Peripheral is the peripheral to enable in sleep mode.
//! The parameter must be one of the following:
//! - \ref PRCM_PERIPH_TIMER0
//! - \ref PRCM_PERIPH_TIMER1
//! - \ref PRCM_PERIPH_TIMER2
//! - \ref PRCM_PERIPH_TIMER3
//! - \ref PRCM_PERIPH_SSI0
//! - \ref PRCM_PERIPH_SSI1
//! - \ref PRCM_PERIPH_UART0
//! - \ref PRCM_PERIPH_UART1
//! - \ref PRCM_PERIPH_I2C0
//! - \ref PRCM_PERIPH_CRYPTO
//! - \ref PRCM_PERIPH_TRNG
//! - \ref PRCM_PERIPH_PKA
//! - \ref PRCM_PERIPH_UDMA
//! - \ref PRCM_PERIPH_GPIO
//! - \ref PRCM_PERIPH_I2S
//!
//! \return None
//!
//! \sa \ref PRCMLoadSet()
//
//*****************************************************************************
extern void PRCMPeripheralSleepEnable(uint32_t ui32Peripheral);

//*****************************************************************************
//
//! \brief Disables a peripheral in sleep mode.
//!
//! This function causes a peripheral to stop operating when the processor goes
//! into sleep mode. Disabling peripherals while in sleep mode helps to lower
//! the current draw of the device. If enabled (via \ref PRCMPeripheralRunEnable()),
//! the peripheral will automatically resume operation when the processor
//! leaves sleep mode, maintaining its entire state from before sleep mode was
//! entered.
//!
//! \note A call to this function will only setup the shadow registers in the
//! MCU domain for the PRCM module. For the changes to propagate to the system
//! controller in the AON domain a call to this function should always be
//! followed by a call to \ref PRCMLoadSet().
//!
//! \param ui32Peripheral is the peripheral to disable in sleep mode.
//! The parameter must be one of the following:
//! - \ref PRCM_PERIPH_TIMER0
//! - \ref PRCM_PERIPH_TIMER1
//! - \ref PRCM_PERIPH_TIMER2
//! - \ref PRCM_PERIPH_TIMER3
//! - \ref PRCM_PERIPH_SSI0
//! - \ref PRCM_PERIPH_SSI1
//! - \ref PRCM_PERIPH_UART0
//! - \ref PRCM_PERIPH_UART1
//! - \ref PRCM_PERIPH_I2C0
//! - \ref PRCM_PERIPH_CRYPTO
//! - \ref PRCM_PERIPH_TRNG
//! - \ref PRCM_PERIPH_PKA
//! - \ref PRCM_PERIPH_UDMA
//! - \ref PRCM_PERIPH_GPIO
//! - \ref PRCM_PERIPH_I2S
//!
//! \return None
//!
//! \sa \ref PRCMLoadSet()
//
//*****************************************************************************
extern void PRCMPeripheralSleepDisable(uint32_t ui32Peripheral);

//*****************************************************************************
//
//! \brief Enables a peripheral in deep-sleep mode.
//!
//! This function allows a peripheral to continue operating when the processor
//! goes into deep-sleep mode.  Since the clocking configuration of the device
//! may change, not all peripherals can safely continue operating while the
//! processor is in sleep mode. This in turn depends on the chosen power mode.
//! It is the responsibility of the caller to make sensible choices.
//!
//! \note A call to this function will only setup the shadow registers in the
//! MCU domain for the PRCM module. For the changes to propagate to the system
//! controller in the AON domain a call to this function should always be
//! followed by a call to \ref PRCMLoadSet().
//!
//! \param ui32Peripheral is the peripheral to enable in deep-sleep mode.
//! The parameter must be one of the following:
//! - \ref PRCM_PERIPH_TIMER0
//! - \ref PRCM_PERIPH_TIMER1
//! - \ref PRCM_PERIPH_TIMER2
//! - \ref PRCM_PERIPH_TIMER3
//! - \ref PRCM_PERIPH_SSI0
//! - \ref PRCM_PERIPH_SSI1
//! - \ref PRCM_PERIPH_UART0
//! - \ref PRCM_PERIPH_UART1
//! - \ref PRCM_PERIPH_I2C0
//! - \ref PRCM_PERIPH_CRYPTO
//! - \ref PRCM_PERIPH_TRNG
//! - \ref PRCM_PERIPH_PKA
//! - \ref PRCM_PERIPH_UDMA
//! - \ref PRCM_PERIPH_GPIO
//! - \ref PRCM_PERIPH_I2S
//!
//! \return None
//!
//! \sa \ref PRCMLoadSet()
//
//*****************************************************************************
extern void PRCMPeripheralDeepSleepEnable(uint32_t ui32Peripheral);

//*****************************************************************************
//
//! \brief Disables a peripheral in deep-sleep mode.
//!
//! This function causes a peripheral to stop operating when the processor goes
//! into deep-sleep mode.  Disabling peripherals while in deep-sleep mode helps
//! to lower the current draw of the device, and can keep peripherals that
//! require a particular clock frequency from operating when the clock changes
//! as a result of entering deep-sleep mode.  If enabled (via
//! \ref PRCMPeripheralRunEnable()), the peripheral will automatically resume
//! operation when the processor leaves deep-sleep mode, maintaining its entire
//! state from before deep-sleep mode was entered.
//!
//! \note A call to this function will only setup the shadow registers in the
//! MCU domain for the PRCM module. For the changes to propagate to the system
//! controller in the AON domain a call to this function should always be
//! followed by a call to \ref PRCMLoadSet().
//!
//! \param ui32Peripheral is the peripheral to disable in deep-sleep mode.
//! The parameter must be one of the following:
//! - \ref PRCM_PERIPH_TIMER0
//! - \ref PRCM_PERIPH_TIMER1
//! - \ref PRCM_PERIPH_TIMER2
//! - \ref PRCM_PERIPH_TIMER3
//! - \ref PRCM_PERIPH_SSI0
//! - \ref PRCM_PERIPH_SSI1
//! - \ref PRCM_PERIPH_UART0
//! - \ref PRCM_PERIPH_UART1
//! - \ref PRCM_PERIPH_I2C0
//! - \ref PRCM_PERIPH_CRYPTO
//! - \ref PRCM_PERIPH_TRNG
//! - \ref PRCM_PERIPH_PKA
//! - \ref PRCM_PERIPH_UDMA
//! - \ref PRCM_PERIPH_GPIO
//! - \ref PRCM_PERIPH_I2S
//!
//! \return None
//!
//! \sa \ref PRCMLoadSet()
//
//*****************************************************************************
extern void PRCMPeripheralDeepSleepDisable(uint32_t ui32Peripheral);

//*****************************************************************************
//
//! \brief Get the status for a specific power domain.
//!
//! Use this function to retrieve the current power status of one or more
//! power domains.
//!
//! \param ui32Domains determines which domain to get the power status for.
//! The parameter must be an OR'ed combination of one or several of:
//! - \ref PRCM_DOMAIN_RFCORE : RF Core.
//! - \ref PRCM_DOMAIN_SERIAL : SSI0, UART0, I2C0
//! - \ref PRCM_DOMAIN_PERIPH : GPT0, GPT1, GPT2, GPT3, GPIO, SSI1, I2S, DMA, UART1
//!
//! \return Returns status of the requested domains:
//! - \ref PRCM_DOMAIN_POWER_OFF : The specified domains are \b all powered down.
//! This status is unconditional and the powered down status is guaranteed.
//! - \ref PRCM_DOMAIN_POWER_OFF : Any of the domains are still powered up.
//
//*****************************************************************************
extern uint32_t PRCMPowerDomainsAllOff(uint32_t ui32Domains);

//*****************************************************************************
//
//! \brief Get the status for a specific power domain.
//!
//! Use this function to retrieve the current power status of one or more
//! power domains.
//!
//! \param ui32Domains determines which domain to get the power status for.
//! The parameter must be an OR'ed combination of one or several of:
//! - \ref PRCM_DOMAIN_RFCORE : RF Core.
//! - \ref PRCM_DOMAIN_SERIAL : SSI0, UART0, I2C0
//! - \ref PRCM_DOMAIN_PERIPH : GPT0, GPT1, GPT2, GPT3, GPIO, SSI1, I2S, DMA, UART1
//!
//! \return Returns status of the requested domains:
//! - \ref PRCM_DOMAIN_POWER_ON  : The specified domains are \b all powered up.
//! This status is unconditional and the powered up status is guaranteed.
//! - \ref PRCM_DOMAIN_POWER_OFF : Any of the domains are still powered down.
//
//*****************************************************************************
extern uint32_t PRCMPowerDomainsAllOn(uint32_t ui32Domains);

//*****************************************************************************
//
//! \brief Return the access status of the RF Core.
//!
//! Use this function to check if the RF Core is on and ready to be accessed.
//! Accessing register or memories that are not powered and clocked will
//! cause a bus fault.
//!
//! \return Returns access status of the RF Core.
//! - \c true  : RF Core can be accessed.
//! - \c false : RF Core domain is not ready for access.
//
//*****************************************************************************
__STATIC_INLINE bool
PRCMRfReady(void)
{
    // Return the ready status of the RF Core.
    return ((HWREG(PRCM_BASE + NONSECURE_OFFSET + PRCM_O_PDSTAT1RFC) &
             PRCM_PDSTAT1RFC_ON) ? true : false);
}


//*****************************************************************************
//
//! \brief Put the processor into sleep mode.
//!
//! This function places the processor into sleep mode; it does not return
//! until the processor returns to run mode.  The peripherals that are enabled
//! via PRCMPeripheralSleepEnable() continue to operate and can wake up the
//! processor.
//!
//! \return None
//!
//! \sa \ref PRCMPeripheralSleepEnable()
//
//*****************************************************************************
__STATIC_INLINE void
PRCMSleep(void)
{
    // Wait for an interrupt.
    CPUwfi();
}

//*****************************************************************************
//
//! \brief Put the processor into deep-sleep mode.
//!
//! This function places the processor into deep-sleep mode; it does not return
//! until the processor returns to run mode.  The peripherals that are enabled
//! via \ref PRCMPeripheralDeepSleepEnable() continue to operate and can wake up
//! the processor.
//!
//! \return None
//!
//! \sa \ref PRCMPeripheralDeepSleepEnable()
//
//*****************************************************************************
extern void PRCMDeepSleep(void);

//*****************************************************************************
//
//! \brief Enable CACHE RAM retention
//!
//! Enables CACHE RAM retention on both VIMS_TRAM and VIMS_CRAM
//!
//! \return None
//
//*****************************************************************************
__STATIC_INLINE void
PRCMCacheRetentionEnable( void )
{
   HWREG( PRCM_BASE + PRCM_O_RAMRETEN ) |= PRCM_RAMRETEN_VIMS_M;
}

//*****************************************************************************
//
//! \brief Disable CACHE RAM retention
//!
//! Disables CACHE RAM retention on both VIMS_TRAM and VIMS_CRAM
//!
//! \return None
//
//*****************************************************************************
__STATIC_INLINE void
PRCMCacheRetentionDisable( void )
{
   HWREG( PRCM_BASE + PRCM_O_RAMRETEN ) &= ~PRCM_RAMRETEN_VIMS_M;
}


//*****************************************************************************
//
// Support for DriverLib in ROM:
// Redirect to implementation in ROM when available.
//
//*****************************************************************************
#if !defined(DRIVERLIB_NOROM) && !defined(DOXYGEN)
    #include "../driverlib/rom.h"
    #ifdef ROM_PRCMInfClockConfigureSet
        #undef  PRCMInfClockConfigureSet
        #define PRCMInfClockConfigureSet        ROM_PRCMInfClockConfigureSet
    #endif
    #ifdef ROM_PRCMInfClockConfigureGet
        #undef  PRCMInfClockConfigureGet
        #define PRCMInfClockConfigureGet        ROM_PRCMInfClockConfigureGet
    #endif
    #ifdef ROM_PRCMAudioClockConfigSet
        #undef  PRCMAudioClockConfigSet
        #define PRCMAudioClockConfigSet         ROM_PRCMAudioClockConfigSet
    #endif
    #ifdef ROM_PRCMAudioClockConfigSetOverride
        #undef  PRCMAudioClockConfigSetOverride
        #define PRCMAudioClockConfigSetOverride ROM_PRCMAudioClockConfigSetOverride
    #endif
    #ifdef ROM_PRCMAudioClockInternalSource
        #undef  PRCMAudioClockInternalSource
        #define PRCMAudioClockInternalSource    ROM_PRCMAudioClockInternalSource
    #endif
    #ifdef ROM_PRCMAudioClockExternalSource
        #undef  PRCMAudioClockExternalSource
        #define PRCMAudioClockExternalSource    ROM_PRCMAudioClockExternalSource
    #endif
    #ifdef ROM_PRCMPowerDomainOn
        #undef  PRCMPowerDomainOn
        #define PRCMPowerDomainOn               ROM_PRCMPowerDomainOn
    #endif
    #ifdef ROM_PRCMPowerDomainOff
        #undef  PRCMPowerDomainOff
        #define PRCMPowerDomainOff              ROM_PRCMPowerDomainOff
    #endif
    #ifdef ROM_PRCMPeripheralRunEnable
        #undef  PRCMPeripheralRunEnable
        #define PRCMPeripheralRunEnable         ROM_PRCMPeripheralRunEnable
    #endif
    #ifdef ROM_PRCMPeripheralRunDisable
        #undef  PRCMPeripheralRunDisable
        #define PRCMPeripheralRunDisable        ROM_PRCMPeripheralRunDisable
    #endif
    #ifdef ROM_PRCMPeripheralSleepEnable
        #undef  PRCMPeripheralSleepEnable
        #define PRCMPeripheralSleepEnable       ROM_PRCMPeripheralSleepEnable
    #endif
    #ifdef ROM_PRCMPeripheralSleepDisable
        #undef  PRCMPeripheralSleepDisable
        #define PRCMPeripheralSleepDisable      ROM_PRCMPeripheralSleepDisable
    #endif
    #ifdef ROM_PRCMPeripheralDeepSleepEnable
        #undef  PRCMPeripheralDeepSleepEnable
        #define PRCMPeripheralDeepSleepEnable   ROM_PRCMPeripheralDeepSleepEnable
    #endif
    #ifdef ROM_PRCMPeripheralDeepSleepDisable
        #undef  PRCMPeripheralDeepSleepDisable
        #define PRCMPeripheralDeepSleepDisable  ROM_PRCMPeripheralDeepSleepDisable
    #endif
    #ifdef ROM_PRCMPowerDomainsAllOff
        #undef  PRCMPowerDomainsAllOff
        #define PRCMPowerDomainsAllOff          ROM_PRCMPowerDomainsAllOff
    #endif
    #ifdef ROM_PRCMPowerDomainsAllOn
        #undef  PRCMPowerDomainsAllOn
        #define PRCMPowerDomainsAllOn           ROM_PRCMPowerDomainsAllOn
    #endif
    #ifdef ROM_PRCMDeepSleep
        #undef  PRCMDeepSleep
        #define PRCMDeepSleep                   ROM_PRCMDeepSleep
    #endif
#endif

//*****************************************************************************
//
// Mark the end of the C bindings section for C++ compilers.
//
//*****************************************************************************
#ifdef __cplusplus
}
#endif

#endif // __PRCM_H__

//*****************************************************************************
//
//! Close the Doxygen group.
//! @}
//! @}
//
//*****************************************************************************