1 /** 2 ****************************************************************************** 3 * @file stm32f1xx_hal_conf.h 4 * @author MCD Application Team 5 * @brief HAL configuration template file. 6 * This file should be copied to the application folder and renamed 7 * to stm32f1xx_hal_conf.h. 8 ****************************************************************************** 9 * @attention 10 * 11 * <h2><center>© Copyright (c) 2017 STMicroelectronics. 12 * All rights reserved.</center></h2> 13 * 14 * This software component is licensed by ST under BSD 3-Clause license, 15 * the "License"; You may not use this file except in compliance with the 16 * License. You may obtain a copy of the License at: 17 * opensource.org/licenses/BSD-3-Clause 18 * 19 ****************************************************************************** 20 */ 21 22 /* Define to prevent recursive inclusion -------------------------------------*/ 23 #ifndef __STM32F1xx_HAL_CONF_H 24 #define __STM32F1xx_HAL_CONF_H 25 26 #ifdef __cplusplus 27 extern "C" { 28 #endif 29 30 /* Exported types ------------------------------------------------------------*/ 31 /* Exported constants --------------------------------------------------------*/ 32 33 /* ########################## Module Selection ############################## */ 34 /** 35 * @brief This is the list of modules to be used in the HAL driver 36 * 37 * Note: 38 * HAL_I2C_MODULE_ENABLED had to be disabled due to the HAL 39 * redefining I2C_SPEED_STANDARD and I2C_SPEED_FAST when the 40 * I2C LL driver was enabled. 41 * 42 */ 43 #define HAL_MODULE_ENABLED 44 #define HAL_ADC_MODULE_ENABLED 45 #define HAL_CAN_MODULE_ENABLED 46 /* #define HAL_CAN_LEGACY_MODULE_ENABLED */ 47 #define HAL_CEC_MODULE_ENABLED 48 #define HAL_CORTEX_MODULE_ENABLED 49 #define HAL_CRC_MODULE_ENABLED 50 #define HAL_DAC_MODULE_ENABLED 51 #define HAL_DMA_MODULE_ENABLED 52 #define HAL_ETH_MODULE_ENABLED 53 #define HAL_EXTI_MODULE_ENABLED 54 #define HAL_FLASH_MODULE_ENABLED 55 #define HAL_GPIO_MODULE_ENABLED 56 #define HAL_HCD_MODULE_ENABLED 57 /* #define HAL_I2C_MODULE_ENABLED */ 58 #define HAL_I2S_MODULE_ENABLED 59 #define HAL_IRDA_MODULE_ENABLED 60 #define HAL_IWDG_MODULE_ENABLED 61 #define HAL_NAND_MODULE_ENABLED 62 #define HAL_NOR_MODULE_ENABLED 63 #define HAL_PCCARD_MODULE_ENABLED 64 #define HAL_PCD_MODULE_ENABLED 65 #define HAL_PWR_MODULE_ENABLED 66 #define HAL_RCC_MODULE_ENABLED 67 #define HAL_RTC_MODULE_ENABLED 68 #define HAL_SD_MODULE_ENABLED 69 #define HAL_SMARTCARD_MODULE_ENABLED 70 #define HAL_SPI_MODULE_ENABLED 71 #define HAL_SRAM_MODULE_ENABLED 72 #define HAL_TIM_MODULE_ENABLED 73 #define HAL_UART_MODULE_ENABLED 74 #define HAL_USART_MODULE_ENABLED 75 #define HAL_WWDG_MODULE_ENABLED 76 #define HAL_MMC_MODULE_ENABLED 77 78 /* ########################## Oscillator Values adaptation ####################*/ 79 /** 80 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 81 * This value is used by the RCC HAL module to compute the system frequency 82 * (when HSE is used as system clock source, directly or through the PLL). 83 */ 84 #if !defined (HSE_VALUE) 85 #if defined(USE_STM3210C_EVAL) 86 #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ 87 #else 88 #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ 89 #endif 90 #endif /* HSE_VALUE */ 91 92 #if !defined (HSE_STARTUP_TIMEOUT) 93 #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ 94 #endif /* HSE_STARTUP_TIMEOUT */ 95 96 /** 97 * @brief Internal High Speed oscillator (HSI) value. 98 * This value is used by the RCC HAL module to compute the system frequency 99 * (when HSI is used as system clock source, directly or through the PLL). 100 */ 101 #if !defined (HSI_VALUE) 102 #define HSI_VALUE 8000000U /*!< Value of the Internal oscillator in Hz */ 103 #endif /* HSI_VALUE */ 104 105 /** 106 * @brief Internal Low Speed oscillator (LSI) value. 107 */ 108 #if !defined (LSI_VALUE) 109 #define LSI_VALUE 40000U /*!< LSI Typical Value in Hz */ 110 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 111 The real value may vary depending on the variations 112 in voltage and temperature. */ 113 /** 114 * @brief External Low Speed oscillator (LSE) value. 115 * This value is used by the UART, RTC HAL module to compute the system frequency 116 */ 117 #if !defined (LSE_VALUE) 118 #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ 119 #endif /* LSE_VALUE */ 120 121 #if !defined (LSE_STARTUP_TIMEOUT) 122 #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ 123 #endif /* LSE_STARTUP_TIMEOUT */ 124 125 /* Tip: To avoid modifying this file each time you need to use different HSE, 126 === you can define the HSE value in your toolchain compiler preprocessor. */ 127 128 /* ########################### System Configuration ######################### */ 129 /** 130 * @brief This is the HAL system configuration section 131 */ 132 #define VDD_VALUE 3300U /*!< Value of VDD in mv */ 133 #define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ 134 #define USE_RTOS 0U 135 #define PREFETCH_ENABLE 1U 136 137 #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ 138 #define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ 139 #define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ 140 #define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ 141 #define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ 142 #define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ 143 #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ 144 #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ 145 #define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ 146 #define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ 147 #define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ 148 #define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ 149 #define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ 150 #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ 151 #define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ 152 #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ 153 #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ 154 #define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ 155 #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ 156 #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ 157 #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ 158 #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ 159 #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ 160 161 /* ########################## Assert Selection ############################## */ 162 /** 163 * @brief Uncomment the line below to expanse the "assert_param" macro in the 164 * HAL drivers code 165 */ 166 /* #define USE_FULL_ASSERT 1U */ 167 168 /* ################## Ethernet peripheral configuration ##################### */ 169 170 /* Section 1 : Ethernet peripheral configuration */ 171 172 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 173 #define MAC_ADDR0 2U 174 #define MAC_ADDR1 0U 175 #define MAC_ADDR2 0U 176 #define MAC_ADDR3 0U 177 #define MAC_ADDR4 0U 178 #define MAC_ADDR5 0U 179 180 /* Definition of the Ethernet driver buffers size and count */ 181 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 182 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 183 #define ETH_RXBUFNB 8U /* 8 Rx buffers of size ETH_RX_BUF_SIZE */ 184 #define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 185 186 /* Section 2: PHY configuration section */ 187 188 /* DP83848 PHY Address*/ 189 #define DP83848_PHY_ADDRESS 0x01U 190 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 191 #define PHY_RESET_DELAY 0x000000FFU 192 /* PHY Configuration delay */ 193 #define PHY_CONFIG_DELAY 0x00000FFFU 194 195 #define PHY_READ_TO 0x0000FFFFU 196 #define PHY_WRITE_TO 0x0000FFFFU 197 198 /* Section 3: Common PHY Registers */ 199 200 #define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ 201 #define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ 202 203 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ 204 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ 205 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ 206 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ 207 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ 208 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ 209 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ 210 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ 211 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ 212 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ 213 214 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ 215 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ 216 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ 217 218 /* Section 4: Extended PHY Registers */ 219 220 #define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ 221 #define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ 222 #define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ 223 224 #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ 225 #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ 226 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ 227 228 #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ 229 #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ 230 231 #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ 232 #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ 233 234 /* ################## SPI peripheral configuration ########################## */ 235 236 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 237 * Activated: CRC code is present inside driver 238 * Deactivated: CRC code cleaned from driver 239 */ 240 241 #define USE_SPI_CRC 1U 242 243 /* Includes ------------------------------------------------------------------*/ 244 /** 245 * @brief Include module's header file 246 */ 247 248 #ifdef HAL_RCC_MODULE_ENABLED 249 #include "stm32f1xx_hal_rcc.h" 250 #endif /* HAL_RCC_MODULE_ENABLED */ 251 252 #ifdef HAL_GPIO_MODULE_ENABLED 253 #include "stm32f1xx_hal_gpio.h" 254 #endif /* HAL_GPIO_MODULE_ENABLED */ 255 256 #ifdef HAL_EXTI_MODULE_ENABLED 257 #include "stm32f1xx_hal_exti.h" 258 #endif /* HAL_EXTI_MODULE_ENABLED */ 259 260 #ifdef HAL_DMA_MODULE_ENABLED 261 #include "stm32f1xx_hal_dma.h" 262 #endif /* HAL_DMA_MODULE_ENABLED */ 263 264 #ifdef HAL_ETH_MODULE_ENABLED 265 #include "stm32f1xx_hal_eth.h" 266 #endif /* HAL_ETH_MODULE_ENABLED */ 267 268 #ifdef HAL_CAN_MODULE_ENABLED 269 #include "stm32f1xx_hal_can.h" 270 #endif /* HAL_CAN_MODULE_ENABLED */ 271 272 #ifdef HAL_CAN_LEGACY_MODULE_ENABLED 273 #include "Legacy/stm32f1xx_hal_can_legacy.h" 274 #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ 275 276 #ifdef HAL_CEC_MODULE_ENABLED 277 #include "stm32f1xx_hal_cec.h" 278 #endif /* HAL_CEC_MODULE_ENABLED */ 279 280 #ifdef HAL_CORTEX_MODULE_ENABLED 281 #include "stm32f1xx_hal_cortex.h" 282 #endif /* HAL_CORTEX_MODULE_ENABLED */ 283 284 #ifdef HAL_ADC_MODULE_ENABLED 285 #include "stm32f1xx_hal_adc.h" 286 #endif /* HAL_ADC_MODULE_ENABLED */ 287 288 #ifdef HAL_CRC_MODULE_ENABLED 289 #include "stm32f1xx_hal_crc.h" 290 #endif /* HAL_CRC_MODULE_ENABLED */ 291 292 #ifdef HAL_DAC_MODULE_ENABLED 293 #include "stm32f1xx_hal_dac.h" 294 #endif /* HAL_DAC_MODULE_ENABLED */ 295 296 #ifdef HAL_FLASH_MODULE_ENABLED 297 #include "stm32f1xx_hal_flash.h" 298 #endif /* HAL_FLASH_MODULE_ENABLED */ 299 300 #ifdef HAL_SRAM_MODULE_ENABLED 301 #include "stm32f1xx_hal_sram.h" 302 #endif /* HAL_SRAM_MODULE_ENABLED */ 303 304 #ifdef HAL_NOR_MODULE_ENABLED 305 #include "stm32f1xx_hal_nor.h" 306 #endif /* HAL_NOR_MODULE_ENABLED */ 307 308 #ifdef HAL_I2C_MODULE_ENABLED 309 #include "stm32f1xx_hal_i2c.h" 310 #endif /* HAL_I2C_MODULE_ENABLED */ 311 312 #ifdef HAL_I2S_MODULE_ENABLED 313 #include "stm32f1xx_hal_i2s.h" 314 #endif /* HAL_I2S_MODULE_ENABLED */ 315 316 #ifdef HAL_IWDG_MODULE_ENABLED 317 #include "stm32f1xx_hal_iwdg.h" 318 #endif /* HAL_IWDG_MODULE_ENABLED */ 319 320 #ifdef HAL_PWR_MODULE_ENABLED 321 #include "stm32f1xx_hal_pwr.h" 322 #endif /* HAL_PWR_MODULE_ENABLED */ 323 324 #ifdef HAL_RTC_MODULE_ENABLED 325 #include "stm32f1xx_hal_rtc.h" 326 #endif /* HAL_RTC_MODULE_ENABLED */ 327 328 #ifdef HAL_PCCARD_MODULE_ENABLED 329 #include "stm32f1xx_hal_pccard.h" 330 #endif /* HAL_PCCARD_MODULE_ENABLED */ 331 332 #ifdef HAL_SD_MODULE_ENABLED 333 #include "stm32f1xx_hal_sd.h" 334 #endif /* HAL_SD_MODULE_ENABLED */ 335 336 #ifdef HAL_NAND_MODULE_ENABLED 337 #include "stm32f1xx_hal_nand.h" 338 #endif /* HAL_NAND_MODULE_ENABLED */ 339 340 #ifdef HAL_SPI_MODULE_ENABLED 341 #include "stm32f1xx_hal_spi.h" 342 #endif /* HAL_SPI_MODULE_ENABLED */ 343 344 #ifdef HAL_TIM_MODULE_ENABLED 345 #include "stm32f1xx_hal_tim.h" 346 #endif /* HAL_TIM_MODULE_ENABLED */ 347 348 #ifdef HAL_UART_MODULE_ENABLED 349 #include "stm32f1xx_hal_uart.h" 350 #endif /* HAL_UART_MODULE_ENABLED */ 351 352 #ifdef HAL_USART_MODULE_ENABLED 353 #include "stm32f1xx_hal_usart.h" 354 #endif /* HAL_USART_MODULE_ENABLED */ 355 356 #ifdef HAL_IRDA_MODULE_ENABLED 357 #include "stm32f1xx_hal_irda.h" 358 #endif /* HAL_IRDA_MODULE_ENABLED */ 359 360 #ifdef HAL_SMARTCARD_MODULE_ENABLED 361 #include "stm32f1xx_hal_smartcard.h" 362 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 363 364 #ifdef HAL_WWDG_MODULE_ENABLED 365 #include "stm32f1xx_hal_wwdg.h" 366 #endif /* HAL_WWDG_MODULE_ENABLED */ 367 368 #ifdef HAL_PCD_MODULE_ENABLED 369 #include "stm32f1xx_hal_pcd.h" 370 #endif /* HAL_PCD_MODULE_ENABLED */ 371 372 #ifdef HAL_HCD_MODULE_ENABLED 373 #include "stm32f1xx_hal_hcd.h" 374 #endif /* HAL_HCD_MODULE_ENABLED */ 375 376 #ifdef HAL_MMC_MODULE_ENABLED 377 #include "stm32f1xx_hal_mmc.h" 378 #endif /* HAL_MMC_MODULE_ENABLED */ 379 380 /* Exported macro ------------------------------------------------------------*/ 381 #ifdef USE_FULL_ASSERT 382 /** 383 * @brief The assert_param macro is used for function's parameters check. 384 * @param expr If expr is false, it calls assert_failed function 385 * which reports the name of the source file and the source 386 * line number of the call that failed. 387 * If expr is true, it returns no value. 388 * @retval None 389 */ 390 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 391 /* Exported functions ------------------------------------------------------- */ 392 void assert_failed(uint8_t* file, uint32_t line); 393 #else 394 #define assert_param(expr) ((void)0U) 395 #endif /* USE_FULL_ASSERT */ 396 397 398 #ifdef __cplusplus 399 } 400 #endif 401 402 #endif /* __STM32F1xx_HAL_CONF_H */ 403 404 405 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 406
