1 /**
2   ******************************************************************************
3   * @file    stm32f4xx_hal_pwr_ex.h
4   * @author  MCD Application Team
5   * @brief   Header file of PWR HAL Extension module.
6   ******************************************************************************
7   * @attention
8   *
9   * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
10   * All rights reserved.</center></h2>
11   *
12   * This software component is licensed by ST under BSD 3-Clause license,
13   * the "License"; You may not use this file except in compliance with the
14   * License. You may obtain a copy of the License at:
15   *                        opensource.org/licenses/BSD-3-Clause
16   *
17   ******************************************************************************
18   */
19 
20 /* Define to prevent recursive inclusion -------------------------------------*/
21 #ifndef __STM32F4xx_HAL_PWR_EX_H
22 #define __STM32F4xx_HAL_PWR_EX_H
23 
24 #ifdef __cplusplus
25  extern "C" {
26 #endif
27 
28 /* Includes ------------------------------------------------------------------*/
29 #include "stm32f4xx_hal_def.h"
30 
31 /** @addtogroup STM32F4xx_HAL_Driver
32   * @{
33   */
34 
35 /** @addtogroup PWREx
36   * @{
37   */
38 
39 /* Exported types ------------------------------------------------------------*/
40 /* Exported constants --------------------------------------------------------*/
41 /** @defgroup PWREx_Exported_Constants PWREx Exported Constants
42   * @{
43   */
44 #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
45     defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
46 
47 /** @defgroup PWREx_Regulator_state_in_UnderDrive_mode PWREx Regulator state in UnderDrive mode
48   * @{
49   */
50 #define PWR_MAINREGULATOR_UNDERDRIVE_ON                       PWR_CR_MRUDS
51 #define PWR_LOWPOWERREGULATOR_UNDERDRIVE_ON                   ((uint32_t)(PWR_CR_LPDS | PWR_CR_LPUDS))
52 /**
53   * @}
54   */
55 
56 /** @defgroup PWREx_Over_Under_Drive_Flag PWREx Over Under Drive Flag
57   * @{
58   */
59 #define PWR_FLAG_ODRDY                  PWR_CSR_ODRDY
60 #define PWR_FLAG_ODSWRDY                PWR_CSR_ODSWRDY
61 #define PWR_FLAG_UDRDY                  PWR_CSR_UDSWRDY
62 /**
63   * @}
64   */
65 #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
66 
67 /** @defgroup PWREx_Regulator_Voltage_Scale PWREx Regulator Voltage Scale
68   * @{
69   */
70 #if defined(STM32F405xx) || defined(STM32F407xx) || defined(STM32F415xx) || defined(STM32F417xx)
71 #define PWR_REGULATOR_VOLTAGE_SCALE1         PWR_CR_VOS             /* Scale 1 mode(default value at reset): the maximum value of fHCLK = 168 MHz. */
72 #define PWR_REGULATOR_VOLTAGE_SCALE2         0x00000000U            /* Scale 2 mode: the maximum value of fHCLK = 144 MHz. */
73 #else
74 #define PWR_REGULATOR_VOLTAGE_SCALE1         PWR_CR_VOS             /* Scale 1 mode(default value at reset): the maximum value of fHCLK is 168 MHz. It can be extended to
75                                                                        180 MHz by activating the over-drive mode. */
76 #define PWR_REGULATOR_VOLTAGE_SCALE2         PWR_CR_VOS_1           /* Scale 2 mode: the maximum value of fHCLK is 144 MHz. It can be extended to
77                                                                        168 MHz by activating the over-drive mode. */
78 #define PWR_REGULATOR_VOLTAGE_SCALE3         PWR_CR_VOS_0           /* Scale 3 mode: the maximum value of fHCLK is 120 MHz. */
79 #endif /* STM32F405xx || STM32F407xx || STM32F415xx || STM32F417xx */
80 /**
81   * @}
82   */
83 #if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \
84     defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx)
85 /** @defgroup PWREx_WakeUp_Pins PWREx WakeUp Pins
86   * @{
87   */
88 #define PWR_WAKEUP_PIN2                 0x00000080U
89 #if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \
90     defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx)
91 #define PWR_WAKEUP_PIN3                 0x00000040U
92 #endif /* STM32F410xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Zx || STM32F412Vx || \
93           STM32F412Rx || STM32F412Cx || STM32F413xx || STM32F423xx */
94 /**
95   * @}
96   */
97 #endif /* STM32F410xx || STM32F446xx || STM32F412Zx || STM32F412Vx || STM32F412Rx || STM32F412Cx ||
98           STM32F413xx || STM32F423xx */
99 
100 /**
101   * @}
102   */
103 
104 /* Exported macro ------------------------------------------------------------*/
105 /** @defgroup PWREx_Exported_Constants PWREx Exported Constants
106   *  @{
107   */
108 
109 #if defined(STM32F405xx) || defined(STM32F407xx) || defined(STM32F415xx) || defined(STM32F417xx)
110 /** @brief  macros configure the main internal regulator output voltage.
111   * @param  __REGULATOR__ specifies the regulator output voltage to achieve
112   *         a tradeoff between performance and power consumption when the device does
113   *         not operate at the maximum frequency (refer to the datasheets for more details).
114   *          This parameter can be one of the following values:
115   *            @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode
116   *            @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode
117   * @retval None
118   */
119 #define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do {                                                     \
120                                                             __IO uint32_t tmpreg = 0x00U;                        \
121                                                             MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__));   \
122                                                             /* Delay after an RCC peripheral clock enabling */  \
123                                                             tmpreg = READ_BIT(PWR->CR, PWR_CR_VOS);             \
124                                                             UNUSED(tmpreg);                                     \
125                                                           } while(0U)
126 #else
127 /** @brief  macros configure the main internal regulator output voltage.
128   * @param  __REGULATOR__ specifies the regulator output voltage to achieve
129   *         a tradeoff between performance and power consumption when the device does
130   *         not operate at the maximum frequency (refer to the datasheets for more details).
131   *          This parameter can be one of the following values:
132   *            @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode
133   *            @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode
134   *            @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode
135   * @retval None
136   */
137 #define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) do {                                                     \
138                                                             __IO uint32_t tmpreg = 0x00U;                        \
139                                                             MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__));   \
140                                                             /* Delay after an RCC peripheral clock enabling */  \
141                                                             tmpreg = READ_BIT(PWR->CR, PWR_CR_VOS);             \
142                                                             UNUSED(tmpreg);                                     \
143                                                           } while(0U)
144 #endif /* STM32F405xx || STM32F407xx || STM32F415xx || STM32F417xx */
145 
146 #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
147     defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
148 /** @brief Macros to enable or disable the Over drive mode.
149   * @note  These macros can be used only for STM32F42xx/STM3243xx devices.
150   */
151 #define __HAL_PWR_OVERDRIVE_ENABLE() (*(__IO uint32_t *) CR_ODEN_BB = ENABLE)
152 #define __HAL_PWR_OVERDRIVE_DISABLE() (*(__IO uint32_t *) CR_ODEN_BB = DISABLE)
153 
154 /** @brief Macros to enable or disable the Over drive switching.
155   * @note  These macros can be used only for STM32F42xx/STM3243xx devices.
156   */
157 #define __HAL_PWR_OVERDRIVESWITCHING_ENABLE() (*(__IO uint32_t *) CR_ODSWEN_BB = ENABLE)
158 #define __HAL_PWR_OVERDRIVESWITCHING_DISABLE() (*(__IO uint32_t *) CR_ODSWEN_BB = DISABLE)
159 
160 /** @brief Macros to enable or disable the Under drive mode.
161   * @note  This mode is enabled only with STOP low power mode.
162   *        In this mode, the 1.2V domain is preserved in reduced leakage mode. This
163   *        mode is only available when the main regulator or the low power regulator
164   *        is in low voltage mode.
165   * @note  If the Under-drive mode was enabled, it is automatically disabled after
166   *        exiting Stop mode.
167   *        When the voltage regulator operates in Under-drive mode, an additional
168   *        startup delay is induced when waking up from Stop mode.
169   */
170 #define __HAL_PWR_UNDERDRIVE_ENABLE() (PWR->CR |= (uint32_t)PWR_CR_UDEN)
171 #define __HAL_PWR_UNDERDRIVE_DISABLE() (PWR->CR &= (uint32_t)(~PWR_CR_UDEN))
172 
173 /** @brief  Check PWR flag is set or not.
174   * @note   These macros can be used only for STM32F42xx/STM3243xx devices.
175   * @param  __FLAG__ specifies the flag to check.
176   *         This parameter can be one of the following values:
177   *            @arg PWR_FLAG_ODRDY: This flag indicates that the Over-drive mode
178   *                                 is ready
179   *            @arg PWR_FLAG_ODSWRDY: This flag indicates that the Over-drive mode
180   *                                   switching is ready
181   *            @arg PWR_FLAG_UDRDY: This flag indicates that the Under-drive mode
182   *                                 is enabled in Stop mode
183   * @retval The new state of __FLAG__ (TRUE or FALSE).
184   */
185 #define __HAL_PWR_GET_ODRUDR_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__))
186 
187 /** @brief Clear the Under-Drive Ready flag.
188   * @note  These macros can be used only for STM32F42xx/STM3243xx devices.
189   */
190 #define __HAL_PWR_CLEAR_ODRUDR_FLAG() (PWR->CSR |= PWR_FLAG_UDRDY)
191 
192 #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
193 /**
194   * @}
195   */
196 
197 /* Exported functions --------------------------------------------------------*/
198 /** @addtogroup PWREx_Exported_Functions PWREx Exported Functions
199   *  @{
200   */
201 
202 /** @addtogroup PWREx_Exported_Functions_Group1
203   * @{
204   */
205 void HAL_PWREx_EnableFlashPowerDown(void);
206 void HAL_PWREx_DisableFlashPowerDown(void);
207 HAL_StatusTypeDef HAL_PWREx_EnableBkUpReg(void);
208 HAL_StatusTypeDef HAL_PWREx_DisableBkUpReg(void);
209 uint32_t HAL_PWREx_GetVoltageRange(void);
210 HAL_StatusTypeDef HAL_PWREx_ControlVoltageScaling(uint32_t VoltageScaling);
211 
212 #if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F401xC) ||\
213     defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F412Zx) || defined(STM32F412Vx) ||\
214     defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx)
215 void HAL_PWREx_EnableMainRegulatorLowVoltage(void);
216 void HAL_PWREx_DisableMainRegulatorLowVoltage(void);
217 void HAL_PWREx_EnableLowRegulatorLowVoltage(void);
218 void HAL_PWREx_DisableLowRegulatorLowVoltage(void);
219 #endif /* STM32F410xx || STM32F401xC || STM32F401xE || STM32F411xE || STM32F412Zx || STM32F412Vx ||\
220           STM32F412Rx || STM32F412Cx || STM32F413xx || STM32F423xx */
221 
222 #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) ||\
223     defined(STM32F469xx) || defined(STM32F479xx)
224 HAL_StatusTypeDef HAL_PWREx_EnableOverDrive(void);
225 HAL_StatusTypeDef HAL_PWREx_DisableOverDrive(void);
226 HAL_StatusTypeDef HAL_PWREx_EnterUnderDriveSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
227 #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
228 
229 /**
230   * @}
231   */
232 
233 /**
234   * @}
235   */
236 /* Private types -------------------------------------------------------------*/
237 /* Private variables ---------------------------------------------------------*/
238 /* Private constants ---------------------------------------------------------*/
239 /** @defgroup PWREx_Private_Constants PWREx Private Constants
240   * @{
241   */
242 
243 /** @defgroup PWREx_register_alias_address PWREx Register alias address
244   * @{
245   */
246 /* ------------- PWR registers bit address in the alias region ---------------*/
247 /* --- CR Register ---*/
248 /* Alias word address of FPDS bit */
249 #define FPDS_BIT_NUMBER          PWR_CR_FPDS_Pos
250 #define CR_FPDS_BB               (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (FPDS_BIT_NUMBER * 4U))
251 
252 /* Alias word address of ODEN bit   */
253 #define ODEN_BIT_NUMBER          PWR_CR_ODEN_Pos
254 #define CR_ODEN_BB               (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (ODEN_BIT_NUMBER * 4U))
255 
256 /* Alias word address of ODSWEN bit */
257 #define ODSWEN_BIT_NUMBER        PWR_CR_ODSWEN_Pos
258 #define CR_ODSWEN_BB             (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (ODSWEN_BIT_NUMBER * 4U))
259 
260 /* Alias word address of MRLVDS bit */
261 #define MRLVDS_BIT_NUMBER        PWR_CR_MRLVDS_Pos
262 #define CR_MRLVDS_BB             (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (MRLVDS_BIT_NUMBER * 4U))
263 
264 /* Alias word address of LPLVDS bit */
265 #define LPLVDS_BIT_NUMBER        PWR_CR_LPLVDS_Pos
266 #define CR_LPLVDS_BB             (uint32_t)(PERIPH_BB_BASE + (PWR_CR_OFFSET_BB * 32U) + (LPLVDS_BIT_NUMBER * 4U))
267 
268  /**
269   * @}
270   */
271 
272 /** @defgroup PWREx_CSR_register_alias PWRx CSR Register alias address
273   * @{
274   */
275 /* --- CSR Register ---*/
276 /* Alias word address of BRE bit */
277 #define BRE_BIT_NUMBER   PWR_CSR_BRE_Pos
278 #define CSR_BRE_BB      (uint32_t)(PERIPH_BB_BASE + (PWR_CSR_OFFSET_BB * 32U) + (BRE_BIT_NUMBER * 4U))
279 
280 /**
281   * @}
282   */
283 
284 /**
285   * @}
286   */
287 
288 /* Private macros ------------------------------------------------------------*/
289 /** @defgroup PWREx_Private_Macros PWREx Private Macros
290   * @{
291   */
292 
293 /** @defgroup PWREx_IS_PWR_Definitions PWREx Private macros to check input parameters
294   * @{
295   */
296 #if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
297     defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
298 #define IS_PWR_REGULATOR_UNDERDRIVE(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_UNDERDRIVE_ON) || \
299                                                 ((REGULATOR) == PWR_LOWPOWERREGULATOR_UNDERDRIVE_ON))
300 #endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
301 
302 #if defined(STM32F405xx) || defined(STM32F407xx) || defined(STM32F415xx) || defined(STM32F417xx)
303 #define IS_PWR_VOLTAGE_SCALING_RANGE(VOLTAGE) (((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
304                                                ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE2))
305 #else
306 #define IS_PWR_VOLTAGE_SCALING_RANGE(VOLTAGE) (((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
307                                                ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \
308                                                ((VOLTAGE) == PWR_REGULATOR_VOLTAGE_SCALE3))
309 #endif /* STM32F405xx || STM32F407xx || STM32F415xx || STM32F417xx */
310 
311 #if defined(STM32F446xx)
312 #define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || ((PIN) == PWR_WAKEUP_PIN2))
313 #elif defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F412Zx) ||\
314       defined(STM32F412Vx) || defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) ||\
315       defined(STM32F423xx)
316 #define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || ((PIN) == PWR_WAKEUP_PIN2) || \
317                                 ((PIN) == PWR_WAKEUP_PIN3))
318 #else
319 #define IS_PWR_WAKEUP_PIN(PIN) ((PIN) == PWR_WAKEUP_PIN1)
320 #endif /* STM32F446xx */
321 /**
322   * @}
323   */
324 
325 /**
326   * @}
327   */
328 
329 /**
330   * @}
331   */
332 
333 /**
334   * @}
335   */
336 
337 #ifdef __cplusplus
338 }
339 #endif
340 
341 
342 #endif /* __STM32F4xx_HAL_PWR_EX_H */
343 
344 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
345