1 /*
2 * Copyright 2018 ,2021 NXP
3 * All rights reserved.
4 *
5 * SPDX-License-Identifier: BSD-3-Clause
6 */
7
8 /***********************************************************************************************************************
9 * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file
10 * will be overwritten if the respective MCUXpresso Config Tools is used to update this file.
11 **********************************************************************************************************************/
12 /*
13 * How to setup clock using clock driver functions:
14 *
15 * 1. Call CLOCK_InitXXX() to configure corresponding SCG clock source.
16 * Note: The clock could not be set when it is being used as system clock.
17 * In default out of reset, the CPU is clocked from FIRC(IRC48M),
18 * so before setting FIRC, change to use another avaliable clock source.
19 *
20 * 2. Call CLOCK_SetXtal0Freq() to set XTAL0 frequency based on board settings.
21 *
22 * 3. Call CLOCK_SetXxxModeSysClkConfig() to set SCG mode for Xxx run mode.
23 * Wait until the system clock source is changed to target source.
24 *
25 * 4. If power mode change is needed, call SMC_SetPowerModeProtection() to allow
26 * corresponding power mode and SMC_SetPowerModeXxx() to change to Xxx mode.
27 * Supported run mode and clock restrictions could be found in Reference Manual.
28 */
29
30 /* clang-format off */
31 /* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
32 !!GlobalInfo
33 product: Clocks v7.0
34 processor: MKE16Z64xxx4
35 package_id: MKE16Z64VLF4
36 mcu_data: ksdk2_0
37 processor_version: 9.0.0
38 board: FRDM-KE16Z
39 * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
40 /* clang-format on */
41
42 #include "fsl_smc.h"
43 #include "clock_config.h"
44
45 /*******************************************************************************
46 * Definitions
47 ******************************************************************************/
48
49 /*******************************************************************************
50 * Variables
51 ******************************************************************************/
52 /* System clock frequency. */
53 extern uint32_t SystemCoreClock;
54
55 /*******************************************************************************
56 * Code
57 ******************************************************************************/
58 /*FUNCTION**********************************************************************
59 *
60 * Function Name : CLOCK_CONFIG_FircSafeConfig
61 * Description : This function is used to safely configure FIRC clock.
62 * In default out of reset, the CPU is clocked from FIRC(IRC48M).
63 * Before setting FIRC, change to use SIRC as system clock,
64 * then configure FIRC. After FIRC is set, change back to use FIRC
65 * in case SIRC need to be configured.
66 * Param fircConfig : FIRC configuration.
67 *
68 *END**************************************************************************/
CLOCK_CONFIG_FircSafeConfig(const scg_firc_config_t * fircConfig)69 static void CLOCK_CONFIG_FircSafeConfig(const scg_firc_config_t *fircConfig)
70 {
71 scg_sys_clk_config_t curConfig;
72 const scg_sirc_config_t scgSircConfig = {.enableMode = kSCG_SircEnable,
73 .div2 = kSCG_AsyncClkDivBy2,
74 .range = kSCG_SircRangeHigh};
75 scg_sys_clk_config_t sysClkSafeConfigSource = {
76 .divSlow = kSCG_SysClkDivBy4, /* Slow clock divider */
77 .divCore = kSCG_SysClkDivBy1, /* Core clock divider */
78 .src = kSCG_SysClkSrcSirc /* System clock source */
79 };
80 /* Init Sirc. */
81 CLOCK_InitSirc(&scgSircConfig);
82 /* Change to use SIRC as system clock source to prepare to change FIRCCFG register. */
83 CLOCK_SetRunModeSysClkConfig(&sysClkSafeConfigSource);
84 /* Wait for clock source switch finished. */
85 do
86 {
87 CLOCK_GetCurSysClkConfig(&curConfig);
88 } while (curConfig.src != sysClkSafeConfigSource.src);
89
90 /* Init Firc. */
91 CLOCK_InitFirc(fircConfig);
92 /* Change back to use FIRC as system clock source in order to configure SIRC if needed. */
93 sysClkSafeConfigSource.src = kSCG_SysClkSrcFirc;
94 CLOCK_SetRunModeSysClkConfig(&sysClkSafeConfigSource);
95 /* Wait for clock source switch finished. */
96 do
97 {
98 CLOCK_GetCurSysClkConfig(&curConfig);
99 } while (curConfig.src != sysClkSafeConfigSource.src);
100 }
101
102 /*******************************************************************************
103 ************************ BOARD_InitBootClocks function ************************
104 ******************************************************************************/
BOARD_InitBootClocks(void)105 void BOARD_InitBootClocks(void)
106 {
107 BOARD_BootClockRUN();
108 }
109
110 /*******************************************************************************
111 ********************** Configuration BOARD_BootClockRUN ***********************
112 ******************************************************************************/
113 /* clang-format off */
114 /* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
115 !!Configuration
116 name: BOARD_BootClockRUN
117 called_from_default_init: true
118 outputs:
119 - {id: Bus_clock.outFreq, value: 24 MHz}
120 - {id: Core_clock.outFreq, value: 48 MHz}
121 - {id: FIRCDIV2_CLK.outFreq, value: 48 MHz}
122 - {id: FLLDIV2_CLK.outFreq, value: 24 MHz}
123 - {id: Flash_clock.outFreq, value: 24 MHz}
124 - {id: LPO1KCLK.outFreq, value: 1 kHz}
125 - {id: LPO_clock.outFreq, value: 128 kHz}
126 - {id: PCC.PCC_ADC0_CLK.outFreq, value: 8 MHz}
127 - {id: PCC.PCC_LPI2C0_CLK.outFreq, value: 8 MHz}
128 - {id: PCC.PCC_LPUART0_CLK.outFreq, value: 8 MHz}
129 - {id: SIRCDIV2_CLK.outFreq, value: 4 MHz}
130 - {id: SIRC_CLK.outFreq, value: 8 MHz}
131 - {id: SOSCDIV2_CLK.outFreq, value: 8 MHz}
132 - {id: SOSC_CLK.outFreq, value: 8 MHz}
133 - {id: System_clock.outFreq, value: 48 MHz}
134 settings:
135 - {id: SCGMode, value: LPFLL}
136 - {id: PCC.PCC_ADC0_SEL.sel, value: SCG.SOSCDIV2_CLK}
137 - {id: PCC.PCC_LPI2C0_SEL.sel, value: SCG.SOSCDIV2_CLK}
138 - {id: PCC.PCC_LPUART0_SEL.sel, value: SCG.SOSCDIV2_CLK}
139 - {id: SCG.FIRCDIV2.scale, value: '1'}
140 - {id: SCG.LPFLLDIV2.scale, value: '2'}
141 - {id: SCG.SCSSEL.sel, value: SCG.LPFLL}
142 - {id: SCG.SIRCDIV2.scale, value: '2'}
143 - {id: SCG.SOSCDIV2.scale, value: '1'}
144 - {id: SCG.TRIMDIV.scale, value: '4'}
145 - {id: SCG_LPFLLCSR_LPFLLEN_CFG, value: Enabled}
146 - {id: SCG_SIRCCSR_SIRCLPEN_CFG, value: Disabled}
147 - {id: SCG_SOSCCFG_OSC_MODE_CFG, value: ModeOscLowPower}
148 - {id: SCG_SOSCCFG_RANGE_CFG, value: Medium}
149 - {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled}
150 - {id: SCG_SOSCCSR_SOSCLPEN_CFG, value: Enabled}
151 sources:
152 - {id: SCG.SOSC.outFreq, value: 8 MHz, enabled: true}
153 * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
154 /* clang-format on */
155
156 /*******************************************************************************
157 * Variables for BOARD_BootClockRUN configuration
158 ******************************************************************************/
159 const scg_sys_clk_config_t g_sysClkConfig_BOARD_BootClockRUN =
160 {
161 .divSlow = kSCG_SysClkDivBy2, /* Slow Clock Divider: divided by 2 */
162 .divCore = kSCG_SysClkDivBy1, /* Core Clock Divider: divided by 1 */
163 .src = kSCG_SysClkSrcLpFll, /* Low power FLL is selected as System Clock Source */
164 };
165 const scg_sosc_config_t g_scgSysOscConfig_BOARD_BootClockRUN =
166 {
167 .freq = 8000000U, /* System Oscillator frequency: 8000000Hz */
168 .enableMode = kSCG_SysOscEnable | kSCG_SysOscEnableInLowPower,/* Enable System OSC clock, Enable System OSC in low power mode */
169 .monitorMode = kSCG_SysOscMonitorDisable, /* Monitor disabled */
170 .div2 = kSCG_AsyncClkDivBy1, /* System OSC Clock Divider 2: divided by 1 */
171 .workMode = kSCG_SysOscModeOscLowPower, /* Oscillator low power */
172 };
173 const scg_sirc_config_t g_scgSircConfig_BOARD_BootClockRUN =
174 {
175 .enableMode = kSCG_SircEnable, /* Enable SIRC clock */
176 .div2 = kSCG_AsyncClkDivBy2, /* Slow IRC Clock Divider 2: divided by 2 */
177 .range = kSCG_SircRangeHigh, /* Slow IRC high range clock (8 MHz) */
178 };
179 const scg_firc_config_t g_scgFircConfig_BOARD_BootClockRUN =
180 {
181 .enableMode = kSCG_FircEnable, /* Enable FIRC clock */
182 .div2 = kSCG_AsyncClkDivBy1, /* Fast IRC Clock Divider 2: divided by 1 */
183 .range = kSCG_FircRange48M, /* Fast IRC is trimmed to 48MHz */
184 .trimConfig = NULL, /* Fast IRC Trim disabled */
185 };
186 const scg_lpfll_config_t g_scgLpFllConfig_BOARD_BootClockRUN =
187 {
188 .enableMode = kSCG_LpFllEnable, /* Enable LPFLL clock */
189 .div2 = kSCG_AsyncClkDivBy2, /* Low Power FLL Clock Divider 2: divided by 2 */
190 .range = kSCG_LpFllRange48M, /* LPFLL is trimmed to 48MHz */
191 .trimConfig = NULL,
192 };
193 /*******************************************************************************
194 * Code for BOARD_BootClockRUN configuration
195 ******************************************************************************/
BOARD_BootClockRUN(void)196 void BOARD_BootClockRUN(void)
197 {
198 scg_sys_clk_config_t curConfig;
199
200 /* Init SOSC according to board configuration. */
201 CLOCK_InitSysOsc(&g_scgSysOscConfig_BOARD_BootClockRUN);
202 /* Set the XTAL0 frequency based on board settings. */
203 CLOCK_SetXtal0Freq(g_scgSysOscConfig_BOARD_BootClockRUN.freq);
204 /* Init FIRC. */
205 CLOCK_CONFIG_FircSafeConfig(&g_scgFircConfig_BOARD_BootClockRUN);
206 /* Init SIRC. */
207 CLOCK_InitSirc(&g_scgSircConfig_BOARD_BootClockRUN);
208 /* Init LPFLL. */
209 CLOCK_InitLpFll(&g_scgLpFllConfig_BOARD_BootClockRUN);
210 /* Set SCG to LPFLL mode. */
211 CLOCK_SetRunModeSysClkConfig(&g_sysClkConfig_BOARD_BootClockRUN);
212 /* Wait for clock source switch finished. */
213 do
214 {
215 CLOCK_GetCurSysClkConfig(&curConfig);
216 } while (curConfig.src != g_sysClkConfig_BOARD_BootClockRUN.src);
217 /* Set SystemCoreClock variable. */
218 SystemCoreClock = BOARD_BOOTCLOCKRUN_CORE_CLOCK;
219 /* Set PCC ADC0 selection */
220 CLOCK_SetIpSrc(kCLOCK_Adc0, kCLOCK_IpSrcSysOscAsync);
221 /* Set PCC LPI2C0 selection */
222 CLOCK_SetIpSrc(kCLOCK_Lpi2c0, kCLOCK_IpSrcSysOscAsync);
223 /* Set PCC LPUART0 selection */
224 CLOCK_SetIpSrc(kCLOCK_Lpuart0, kCLOCK_IpSrcSysOscAsync);
225 }
226
227 /*******************************************************************************
228 ********************* Configuration BOARD_BootClockVLPR ***********************
229 ******************************************************************************/
230 /* clang-format off */
231 /* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
232 !!Configuration
233 name: BOARD_BootClockVLPR
234 outputs:
235 - {id: Bus_clock.outFreq, value: 1 MHz}
236 - {id: Core_clock.outFreq, value: 4 MHz}
237 - {id: Flash_clock.outFreq, value: 1 MHz}
238 - {id: LPO1KCLK.outFreq, value: 1 kHz}
239 - {id: LPO_clock.outFreq, value: 128 kHz}
240 - {id: SOSCDIV2_CLK.outFreq, value: 8 MHz}
241 - {id: SOSC_CLK.outFreq, value: 8 MHz}
242 - {id: System_clock.outFreq, value: 4 MHz}
243 settings:
244 - {id: SCGMode, value: SOSC}
245 - {id: powerMode, value: VLPR}
246 - {id: SCG.DIVCORE.scale, value: '2', locked: true}
247 - {id: SCG.DIVSLOW.scale, value: '4', locked: true}
248 - {id: SCG.FIRCDIV2.scale, value: '1'}
249 - {id: SCG.LPFLLDIV2.scale, value: '2'}
250 - {id: SCG.SCSSEL.sel, value: SCG.SOSC}
251 - {id: SCG.SIRCDIV2.scale, value: '2'}
252 - {id: SCG.SOSCDIV2.scale, value: '1'}
253 - {id: SCG_LPFLLCSR_LPFLLEN_CFG, value: Enabled}
254 - {id: SCG_SIRCCSR_SIRCLPEN_CFG, value: Disabled}
255 - {id: SCG_SOSCCFG_OSC_MODE_CFG, value: ModeOscLowPower}
256 - {id: SCG_SOSCCFG_RANGE_CFG, value: Medium}
257 - {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled}
258 - {id: SCG_SOSCCSR_SOSCLPEN_CFG, value: Enabled}
259 sources:
260 - {id: SCG.SOSC.outFreq, value: 8 MHz, enabled: true}
261 * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
262 /* clang-format on */
263
264 /*******************************************************************************
265 * Variables for BOARD_BootClockVLPR configuration
266 ******************************************************************************/
267 const scg_sys_clk_config_t g_sysClkConfig_BOARD_BootClockVLPR =
268 {
269 .divSlow = kSCG_SysClkDivBy4, /* Slow Clock Divider: divided by 4 */
270 .divCore = kSCG_SysClkDivBy2, /* Core Clock Divider: divided by 2 */
271 .src = kSCG_SysClkSrcSysOsc, /* System OSC is selected as System Clock Source */
272 };
273 const scg_sosc_config_t g_scgSysOscConfig_BOARD_BootClockVLPR =
274 {
275 .freq = 8000000U, /* System Oscillator frequency: 8000000Hz */
276 .enableMode = kSCG_SysOscEnable | kSCG_SysOscEnableInLowPower,/* Enable System OSC clock, Enable System OSC in low power mode */
277 .monitorMode = kSCG_SysOscMonitorDisable, /* Monitor disabled */
278 .div2 = kSCG_AsyncClkDivBy1, /* System OSC Clock Divider 2: divided by 1 */
279 .workMode = kSCG_SysOscModeOscLowPower, /* Oscillator low power */
280 };
281 const scg_sirc_config_t g_scgSircConfig_BOARD_BootClockVLPR =
282 {
283 .enableMode = kSCG_SircEnable, /* Enable SIRC clock */
284 .div2 = kSCG_AsyncClkDivBy2, /* Slow IRC Clock Divider 2: divided by 2 */
285 .range = kSCG_SircRangeHigh, /* Slow IRC high range clock (8 MHz) */
286 };
287 const scg_firc_config_t g_scgFircConfig_BOARD_BootClockVLPR =
288 {
289 .enableMode = kSCG_FircEnable, /* Enable FIRC clock */
290 .div2 = kSCG_AsyncClkDivBy1, /* Fast IRC Clock Divider 2: divided by 1 */
291 .range = kSCG_FircRange48M, /* Fast IRC is trimmed to 48MHz */
292 .trimConfig = NULL, /* Fast IRC Trim disabled */
293 };
294 const scg_lpfll_config_t g_scgLpFllConfig_BOARD_BootClockVLPR =
295 {
296 .enableMode = kSCG_LpFllEnable, /* Enable LPFLL clock */
297 .div2 = kSCG_AsyncClkDivBy2, /* Low Power FLL Clock Divider 2: divided by 2 */
298 .range = kSCG_LpFllRange48M, /* LPFLL is trimmed to 48MHz */
299 .trimConfig = NULL,
300 };
301 /*******************************************************************************
302 * Code for BOARD_BootClockVLPR configuration
303 ******************************************************************************/
BOARD_BootClockVLPR(void)304 void BOARD_BootClockVLPR(void)
305 {
306 /* Init SOSC according to board configuration. */
307 CLOCK_InitSysOsc(&g_scgSysOscConfig_BOARD_BootClockVLPR);
308 /* Set the XTAL0 frequency based on board settings. */
309 CLOCK_SetXtal0Freq(g_scgSysOscConfig_BOARD_BootClockVLPR.freq);
310 /* Set SCG to SOSC mode. */
311 CLOCK_SetVlprModeSysClkConfig(&g_sysClkConfig_BOARD_BootClockVLPR);
312 /* Allow SMC all power modes. */
313 SMC_SetPowerModeProtection(SMC, kSMC_AllowPowerModeAll);
314 /* Set VLPR power mode. */
315 SMC_SetPowerModeVlpr(SMC);
316 while (SMC_GetPowerModeState(SMC) != kSMC_PowerStateVlpr)
317 {
318 }
319 /* Set SystemCoreClock variable. */
320 SystemCoreClock = BOARD_BOOTCLOCKVLPR_CORE_CLOCK;
321 }
322
323
