1 /*
2 * Copyright (c) 2022 Henrik Brix Andersen <henrik@brixandersen.dk>
3 * Copyright (c) 2022 Martin Jäger <martin@libre.solar>
4 *
5 * SPDX-License-Identifier: Apache-2.0
6 */
7
8 #define DT_DRV_COMPAT espressif_esp32_twai
9
10 #include <zephyr/drivers/can/can_sja1000.h>
11
12 #include <zephyr/drivers/can.h>
13 #include <zephyr/drivers/clock_control.h>
14 #include <zephyr/drivers/interrupt_controller/intc_esp32.h>
15 #include <zephyr/drivers/pinctrl.h>
16 #include <zephyr/logging/log.h>
17
18 #include <soc.h>
19
20 LOG_MODULE_REGISTER(can_esp32_twai, CONFIG_CAN_LOG_LEVEL);
21
22 /*
23 * Newer ESP32-series MCUs like ESP32-C3 and ESP32-S2 have some slightly different registers
24 * compared to the original ESP32, which is fully compatible with the SJA1000 controller.
25 *
26 * The names with TWAI_ prefixes from Espressif reference manuals are used for these incompatible
27 * registers.
28 */
29 #ifndef CONFIG_SOC_SERIES_ESP32
30
31 /* TWAI_BUS_TIMING_0_REG is incompatible with CAN_SJA1000_BTR0 */
32 #define TWAI_BUS_TIMING_0_REG (6U)
33 #define TWAI_BAUD_PRESC_MASK GENMASK(12, 0)
34 #define TWAI_SYNC_JUMP_WIDTH_MASK GENMASK(15, 14)
35 #define TWAI_BAUD_PRESC_PREP(brp) FIELD_PREP(TWAI_BAUD_PRESC_MASK, brp)
36 #define TWAI_SYNC_JUMP_WIDTH_PREP(sjw) FIELD_PREP(TWAI_SYNC_JUMP_WIDTH_MASK, sjw)
37
38 /*
39 * TWAI_BUS_TIMING_1_REG is compatible with CAN_SJA1000_BTR1, but needed here for the custom
40 * set_timing() function.
41 */
42 #define TWAI_BUS_TIMING_1_REG (7U)
43 #define TWAI_TIME_SEG1_MASK GENMASK(3, 0)
44 #define TWAI_TIME_SEG2_MASK GENMASK(6, 4)
45 #define TWAI_TIME_SAMP BIT(7)
46 #define TWAI_TIME_SEG1_PREP(seg1) FIELD_PREP(TWAI_TIME_SEG1_MASK, seg1)
47 #define TWAI_TIME_SEG2_PREP(seg2) FIELD_PREP(TWAI_TIME_SEG2_MASK, seg2)
48
49 /* TWAI_CLOCK_DIVIDER_REG is incompatible with CAN_SJA1000_CDR */
50 #define TWAI_CLOCK_DIVIDER_REG (31U)
51 #define TWAI_CD_MASK GENMASK(7, 0)
52 #define TWAI_CLOCK_OFF BIT(8)
53
54 /*
55 * Further incompatible registers currently not used by the driver:
56 * - TWAI_STATUS_REG has new bit 8: TWAI_MISS_ST
57 * - TWAI_INT_RAW_REG has new bit 8: TWAI_BUS_STATE_INT_ST
58 * - TWAI_INT_ENA_REG has new bit 8: TWAI_BUS_STATE_INT_ENA
59 */
60 #else
61
62 /* Redefinitions of the SJA1000 CDR bits to simplify driver config */
63 #define TWAI_CD_MASK GENMASK(2, 0)
64 #define TWAI_CLOCK_OFF BIT(3)
65
66 #endif /* !CONFIG_SOC_SERIES_ESP32 */
67
68 struct can_esp32_twai_config {
69 mm_reg_t base;
70 const struct pinctrl_dev_config *pcfg;
71 const struct device *clock_dev;
72 const clock_control_subsys_t clock_subsys;
73 int irq_source;
74 #ifndef CONFIG_SOC_SERIES_ESP32
75 /* 32-bit variant of output clock divider register required for non-ESP32 MCUs */
76 uint32_t cdr32;
77 #endif /* !CONFIG_SOC_SERIES_ESP32 */
78 };
79
can_esp32_twai_read_reg(const struct device * dev,uint8_t reg)80 static uint8_t can_esp32_twai_read_reg(const struct device *dev, uint8_t reg)
81 {
82 const struct can_sja1000_config *sja1000_config = dev->config;
83 const struct can_esp32_twai_config *twai_config = sja1000_config->custom;
84 mm_reg_t addr = twai_config->base + reg * sizeof(uint32_t);
85
86 return sys_read32(addr) & 0xFF;
87 }
88
can_esp32_twai_write_reg(const struct device * dev,uint8_t reg,uint8_t val)89 static void can_esp32_twai_write_reg(const struct device *dev, uint8_t reg, uint8_t val)
90 {
91 const struct can_sja1000_config *sja1000_config = dev->config;
92 const struct can_esp32_twai_config *twai_config = sja1000_config->custom;
93 mm_reg_t addr = twai_config->base + reg * sizeof(uint32_t);
94
95 sys_write32(val & 0xFF, addr);
96 }
97
98 #ifndef CONFIG_SOC_SERIES_ESP32
99
100 /*
101 * Required for newer ESP32-series MCUs which violate the original SJA1000 8-bit register size.
102 */
can_esp32_twai_write_reg32(const struct device * dev,uint8_t reg,uint32_t val)103 static void can_esp32_twai_write_reg32(const struct device *dev, uint8_t reg, uint32_t val)
104 {
105 const struct can_sja1000_config *sja1000_config = dev->config;
106 const struct can_esp32_twai_config *twai_config = sja1000_config->custom;
107 mm_reg_t addr = twai_config->base + reg * sizeof(uint32_t);
108
109 sys_write32(val, addr);
110 }
111
112 /*
113 * Custom implementation instead of can_sja1000_set_timing required because TWAI_BUS_TIMING_0_REG
114 * is incompatible with CAN_SJA1000_BTR0.
115 */
can_esp32_twai_set_timing(const struct device * dev,const struct can_timing * timing)116 static int can_esp32_twai_set_timing(const struct device *dev, const struct can_timing *timing)
117 {
118 struct can_sja1000_data *data = dev->data;
119 uint8_t btr0;
120 uint8_t btr1;
121
122 if (data->common.started) {
123 return -EBUSY;
124 }
125
126 k_mutex_lock(&data->mod_lock, K_FOREVER);
127
128 btr0 = TWAI_BAUD_PRESC_PREP(timing->prescaler - 1) |
129 TWAI_SYNC_JUMP_WIDTH_PREP(timing->sjw - 1);
130 btr1 = TWAI_TIME_SEG1_PREP(timing->phase_seg1 - 1) |
131 TWAI_TIME_SEG2_PREP(timing->phase_seg2 - 1);
132
133 if ((data->common.mode & CAN_MODE_3_SAMPLES) != 0) {
134 btr1 |= TWAI_TIME_SAMP;
135 }
136
137 can_esp32_twai_write_reg32(dev, TWAI_BUS_TIMING_0_REG, btr0);
138 can_esp32_twai_write_reg32(dev, TWAI_BUS_TIMING_1_REG, btr1);
139
140 k_mutex_unlock(&data->mod_lock);
141
142 return 0;
143 }
144
145 #endif /* !CONFIG_SOC_SERIES_ESP32 */
146
can_esp32_twai_get_core_clock(const struct device * dev,uint32_t * rate)147 static int can_esp32_twai_get_core_clock(const struct device *dev, uint32_t *rate)
148 {
149 ARG_UNUSED(dev);
150
151 /* The internal clock operates at half of the oscillator frequency */
152 *rate = APB_CLK_FREQ / 2;
153
154 return 0;
155 }
156
can_esp32_twai_isr(void * arg)157 static void IRAM_ATTR can_esp32_twai_isr(void *arg)
158 {
159 const struct device *dev = (const struct device *)arg;
160
161 can_sja1000_isr(dev);
162 }
163
can_esp32_twai_init(const struct device * dev)164 static int can_esp32_twai_init(const struct device *dev)
165 {
166 const struct can_sja1000_config *sja1000_config = dev->config;
167 const struct can_esp32_twai_config *twai_config = sja1000_config->custom;
168 int err;
169
170 if (!device_is_ready(twai_config->clock_dev)) {
171 LOG_ERR("clock control device not ready");
172 return -ENODEV;
173 }
174
175 err = pinctrl_apply_state(twai_config->pcfg, PINCTRL_STATE_DEFAULT);
176 if (err != 0) {
177 LOG_ERR("failed to configure TWAI pins (err %d)", err);
178 return err;
179 }
180
181 err = clock_control_on(twai_config->clock_dev, twai_config->clock_subsys);
182 if (err != 0) {
183 LOG_ERR("failed to enable CAN clock (err %d)", err);
184 return err;
185 }
186
187 err = can_sja1000_init(dev);
188 if (err != 0) {
189 LOG_ERR("failed to initialize controller (err %d)", err);
190 return err;
191 }
192
193 #ifndef CONFIG_SOC_SERIES_ESP32
194 /*
195 * TWAI_CLOCK_DIVIDER_REG is incompatible with CAN_SJA1000_CDR for non-ESP32 MCUs
196 * - TWAI_CD has length of 8 bits instead of 3 bits
197 * - TWAI_CLOCK_OFF at BIT(8) instead of BIT(3)
198 * - TWAI_EXT_MODE bit missing (always "extended" = PeliCAN mode)
199 *
200 * Overwrite with 32-bit register variant configured via devicetree.
201 */
202 can_esp32_twai_write_reg32(dev, TWAI_CLOCK_DIVIDER_REG, twai_config->cdr32);
203 #endif /* !CONFIG_SOC_SERIES_ESP32 */
204
205 esp_intr_alloc(twai_config->irq_source, 0, can_esp32_twai_isr, (void *)dev, NULL);
206
207 return 0;
208 }
209
210 const struct can_driver_api can_esp32_twai_driver_api = {
211 .get_capabilities = can_sja1000_get_capabilities,
212 .start = can_sja1000_start,
213 .stop = can_sja1000_stop,
214 .set_mode = can_sja1000_set_mode,
215 #ifdef CONFIG_SOC_SERIES_ESP32
216 .set_timing = can_sja1000_set_timing,
217 #else
218 .set_timing = can_esp32_twai_set_timing,
219 #endif /* CONFIG_SOC_SERIES_ESP32 */
220 .send = can_sja1000_send,
221 .add_rx_filter = can_sja1000_add_rx_filter,
222 .remove_rx_filter = can_sja1000_remove_rx_filter,
223 .get_state = can_sja1000_get_state,
224 .set_state_change_callback = can_sja1000_set_state_change_callback,
225 .get_core_clock = can_esp32_twai_get_core_clock,
226 .get_max_filters = can_sja1000_get_max_filters,
227 #ifndef CONFIG_CAN_AUTO_BUS_OFF_RECOVERY
228 .recover = can_sja1000_recover,
229 #endif /* !CONFIG_CAN_AUTO_BUS_OFF_RECOVERY */
230 .timing_min = CAN_SJA1000_TIMING_MIN_INITIALIZER,
231 #ifdef CONFIG_SOC_SERIES_ESP32
232 .timing_max = CAN_SJA1000_TIMING_MAX_INITIALIZER,
233 #else
234 /* larger prescaler allowed for newer ESP32-series MCUs */
235 .timing_max = {
236 .sjw = 0x4,
237 .prop_seg = 0x0,
238 .phase_seg1 = 0x10,
239 .phase_seg2 = 0x8,
240 .prescaler = 0x2000,
241 }
242 #endif /* CONFIG_SOC_SERIES_ESP32 */
243 };
244
245 #ifdef CONFIG_SOC_SERIES_ESP32
246 #define TWAI_CLKOUT_DIVIDER_MAX (14)
247 #define TWAI_CDR32_INIT(inst)
248 #else
249 #define TWAI_CLKOUT_DIVIDER_MAX (490)
250 #define TWAI_CDR32_INIT(inst) .cdr32 = CAN_ESP32_TWAI_DT_CDR_INST_GET(inst)
251 #endif /* CONFIG_SOC_SERIES_ESP32 */
252
253 #define CAN_ESP32_TWAI_ASSERT_CLKOUT_DIVIDER(inst) \
254 BUILD_ASSERT(COND_CODE_0(DT_INST_NODE_HAS_PROP(inst, clkout_divider), (1), \
255 (DT_INST_PROP(inst, clkout_divider) == 1 || \
256 (DT_INST_PROP(inst, clkout_divider) % 2 == 0 && \
257 DT_INST_PROP(inst, clkout_divider) / 2 <= TWAI_CLKOUT_DIVIDER_MAX))), \
258 "TWAI clkout-divider from dts invalid")
259
260 #define CAN_ESP32_TWAI_DT_CDR_INST_GET(inst) \
261 COND_CODE_1(DT_INST_NODE_HAS_PROP(inst, clkout_divider), \
262 COND_CODE_1(DT_INST_PROP(inst, clkout_divider) == 1, (TWAI_CD_MASK), \
263 ((DT_INST_PROP(inst, clkout_divider)) / 2 - 1)), \
264 (TWAI_CLOCK_OFF))
265
266 #define CAN_ESP32_TWAI_INIT(inst) \
267 PINCTRL_DT_INST_DEFINE(inst); \
268 \
269 static const struct can_esp32_twai_config can_esp32_twai_config_##inst = { \
270 .base = DT_INST_REG_ADDR(inst), \
271 .clock_dev = DEVICE_DT_GET(DT_INST_CLOCKS_CTLR(inst)), \
272 .clock_subsys = (clock_control_subsys_t)DT_INST_CLOCKS_CELL(inst, offset), \
273 .pcfg = PINCTRL_DT_INST_DEV_CONFIG_GET(inst), \
274 .irq_source = DT_INST_IRQN(inst), \
275 TWAI_CDR32_INIT(inst) \
276 }; \
277 CAN_ESP32_TWAI_ASSERT_CLKOUT_DIVIDER(inst); \
278 static const struct can_sja1000_config can_sja1000_config_##inst = \
279 CAN_SJA1000_DT_CONFIG_INST_GET(inst, &can_esp32_twai_config_##inst, \
280 can_esp32_twai_read_reg, can_esp32_twai_write_reg, \
281 CAN_SJA1000_OCR_OCMODE_BIPHASE, \
282 COND_CODE_0(IS_ENABLED(CONFIG_SOC_SERIES_ESP32), (0), \
283 (CAN_ESP32_TWAI_DT_CDR_INST_GET(inst)))); \
284 \
285 static struct can_sja1000_data can_sja1000_data_##inst = \
286 CAN_SJA1000_DATA_INITIALIZER(NULL); \
287 \
288 CAN_DEVICE_DT_INST_DEFINE(inst, can_esp32_twai_init, NULL, &can_sja1000_data_##inst, \
289 &can_sja1000_config_##inst, POST_KERNEL, \
290 CONFIG_CAN_INIT_PRIORITY, &can_esp32_twai_driver_api);
291
292 DT_INST_FOREACH_STATUS_OKAY(CAN_ESP32_TWAI_INIT)
293
