Searched refs:will (Results 876 – 900 of 1633) sorted by relevance
1...<<31323334353637383940>>...66
| /Zephyr-latest/drivers/ethernet/ |
| D | Kconfig.adin2111 | 42 that the driver will wait from the IP stack to get
|
| /Zephyr-latest/doc/develop/toolchains/ |
| D | gnu_arm_embedded.rst | 13 path used by the ARM GCC installer, in which case you will need to adjust the path
|
| /Zephyr-latest/doc/hardware/peripherals/ |
| D | video.rst | 40 represents a video control property. Different devices will have different
|
| /Zephyr-latest/boards/adafruit/feather_m4_express/ |
| D | adafruit_feather_m4_express.dts | 115 * Storage partition will be used by FCB/LittleFS/NVS
|
| /Zephyr-latest/tests/ztest/fail/ |
| D | CMakeLists.txt | 35 # Add the 'core' external project which will mirror the configs of this project.
|
| /Zephyr-latest/boards/adafruit/feather_m0_lora/ |
| D | adafruit_feather_m0_lora.dts | 109 * Storage partition will be used by FCB/LittleFS/NVS
|
| /Zephyr-latest/.github/ISSUE_TEMPLATE/ |
| D | 003_rfc-proposal.md | 24 A brief summary of the proposed change - the 10,000 ft view on what it will
|
| /Zephyr-latest/samples/bluetooth/hci_spi/ |
| D | README.rst | 34 You will also need a separate chip acting as BT HCI SPI master. This
|
| /Zephyr-latest/boards/microchip/ev11l78a/ |
| D | ev11l78a.dts | 96 * Storage partition will be used by FCB/LittleFS/NVS
|
| /Zephyr-latest/boards/nxp/mimxrt1064_evk/ |
| D | CMakeLists.txt | 47 "This timer will enable lower power modes, but at the cost of reduced "
|
| /Zephyr-latest/boards/nxp/mimxrt1040_evk/ |
| D | CMakeLists.txt | 47 "This timer will enable lower power modes, but at the cost of reduced "
|
| /Zephyr-latest/boards/nxp/mimxrt1170_evk/ |
| D | CMakeLists.txt | 47 "This timer will enable lower power modes, but at the cost of reduced "
|
| /Zephyr-latest/arch/x86/ |
| D | CMakeLists.txt | 39 # Make the string into a list, or else it will be passed to ${GEN_MMU}
|
| /Zephyr-latest/boards/arduino/zero/ |
| D | arduino_zero.dts | 120 * Storage partition will be used by FCB/LittleFS/NVS
|
| /Zephyr-latest/boards/st/stm32l562e_dk/doc/ |
| D | index.rst | 226 will set platform option bytes config and erase platform (among others,
227 option bit TZEN will be set).
234 Please note that, after having run a TFM sample on the board, you will need to
238 Also note that, even then, TZEN will remain set, and you will need to use
|
| /Zephyr-latest/doc/develop/tools/ |
| D | coccinelle.rst | 23 Using earlier versions will fail as the option names used by
147 if support for this is detected you will benefit from parmap parallelization.
149 When parmap is enabled ``coccicheck`` will enable dynamic load balancing by using
384 will execute the following part of the SmPL script:
437 will execute the following part of the SmPL script:
499 will execute the following part of the SmPL script:
549 will execute the following part of the SmPL script:
|
| D | stm32cubeide.rst | 69 ``<build dir>/zephyr/include/generated/autoconf.h``. This will ensure
71 The following dialog will be shown. Fill it in as follows:
|
| /Zephyr-latest/doc/services/pm/ |
| D | device.rst | 10 selected, device drivers implementing power management will be able to take
57 may not know that a subsystem will perform a series of sequential
82 subsystem will check if the selected low power state triggers device power
138 When using this method of device power management, the CPU will not
306 the system will not do power management on it. After the device is no
394 * sleep state would be suitable but constraints will
395 * make only state0 (suspend-to-idle) will be used.
|
| /Zephyr-latest/subsys/logging/backends/ |
| D | Kconfig.net | 109 IPv6 the size is 1180 octets. As each buffer will use RAM, the value
110 should be selected so that typical messages will fit the buffer.
|
| /Zephyr-latest/drivers/spi/ |
| D | Kconfig.nrfx | 83 RXD.MAXCNT == 1 and TXD.MAXCNT <= 1 will NOT be executed
105 will fail.
|
| /Zephyr-latest/subsys/mgmt/updatehub/ |
| D | Kconfig | 35 Set the interval that the UpdateHub update server will be polled.
134 option is enabled, the data stream will be read back from the
|
| /Zephyr-latest/boards/shields/esp_8266/doc/ |
| D | index.rst | 65 This tutorial won't explain how firmware must be upgraded. However, it will
86 Networking -> Link Layer Options. This will avoid problems running
|
| /Zephyr-latest/doc/connectivity/networking/api/ |
| D | capture.rst | 21 If capturing is enabled and configured, the system will automatically capture
93 The ``net capture enable 2`` net-shell command will cause the packets sent to
|
| /Zephyr-latest/samples/shields/npm6001_ek/doc/ |
| D | index.rst | 163 # enable watchdog, timeout set to 8 seconds. Timeout will be rounded up to
172 When the watchdog reset pin is connected to your board reset, you will see
|
| /Zephyr-latest/cmake/compiler/ |
| D | compiler_flags_template.cmake | 22 # Property for standard warning base in Zephyr, this will always bet set when compiling.
36 # Compiler property that will issue error if a declaration does not specify a type
|
1...<<31323334353637383940>>...66
