Searched refs:supports (Results 151 – 175 of 742) sorted by relevance
12345678910>>...30
| /Zephyr-latest/drivers/dma/ |
| D | Kconfig.dw_axi_dmac | 24 bool "hardware supports linked list multi block transfer"
|
| /Zephyr-latest/samples/sensor/magn_polling/ |
| D | README.rst | 21 that supports 32-bit SPI_WORD_SIZE. On the :zephyr:board:`rpi_pico`, the
|
| /Zephyr-latest/samples/sensor/max6675/ |
| D | README.rst | 28 This sample can be built with any board that supports SPI. A sample overlay is
|
| /Zephyr-latest/samples/bluetooth/periodic_adv_conn/ |
| D | README.rst | 22 * A controller that supports the Periodic Advertising with Responses (PAwR) - Advertiser feature
|
| /Zephyr-latest/samples/sensor/tdk_apex/ |
| D | README.rst | 43 This sample supports TDK IMU devices. Each device needs
54 This sample supports APEX feature of TDK device. It needs to be specified as below:
|
| /Zephyr-latest/boards/sparkfun/micromod/doc/ |
| D | index.rst | 32 Zephyr currently supports the following SoCs:
51 The ``micromod/nrf52840`` board target supports the following
75 The Zephyr ``micromod/nrf52840`` board target supports the following hardware
|
| /Zephyr-latest/boards/infineon/cy8ckit_062s4/doc/ |
| D | index.rst | 7 supports low-power operations, up to 256 KB Flash and 128 KB SRAM, programmable analog sensing,
13 user LEDs, and a push button. The board supports operating voltages from 1.8 V to 3.3 V for PSoC™ 6…
62 …ommands use OpenOCD and require a custom Infineon OpenOCD version, that supports KitProg3, to be i…
|
| /Zephyr-latest/boards/qemu/x86/doc/ |
| D | index.rst | 22 This configuration supports the following hardware features:
106 For qemu_x86_64 platform, it also supports to use UEFI bootable method
174 The board supports SLIP networking over an emulated serial port
|
| /Zephyr-latest/boards/96boards/wistrio/doc/ |
| D | 96b_wistrio.rst | 48 The Zephyr 96b_wistrio board configuration supports the following hardware
131 which can be triggered by using the BOOT0 pin. The ROM bootloader supports
148 Chapter 29 of Application note `AN2606`_. The ROM bootloader supports flashing
|
| /Zephyr-latest/boards/nxp/frdm_rw612/doc/ |
| D | index.rst | 143 RW612 supports shared access of the SRAM from both the code bus and data bus.
174 frdm_rw612 platform supports the monolithic feature. The required binary blob
184 frdm_rw612 platform supports the monolithic feature. The required binary blob
|
| /Zephyr-latest/boards/nxp/ls1046ardb/doc/ |
| D | index.rst | 7 evaluation, and development platform that supports the Layerscape LS1046A
8 architecture processor. The LS1046ARDB board supports the Layerscape LS1046A
22 LS1046A RDB boards supports the following features:
50 NXP LS1046A RDB board default configuration supports the following
|
| /Zephyr-latest/boards/shields/dvp_fpc24_mt9m114/doc/ |
| D | index.rst | 9 This shield supports mt9m114 camera modules which use a 24-pin FPC connector and a DVP
|
| /Zephyr-latest/boards/shields/mikroe_accel13_click/doc/ |
| D | index.rst | 12 The `IIS2DLPC`_ sensor supports both SPI and I2C bus protocols. Currently
|
| /Zephyr-latest/drivers/sensor/ite/ite_vcmp_it8xxx2/ |
| D | Kconfig | 13 it8xxx2 supports six 10-bit resolution voltage comparator
|
| /Zephyr-latest/boards/shields/tcan4550evm/doc/ |
| D | index.rst | 27 TCAN4550-Q1 supports up to 18MHz SPI clock frequency. This is done to accommodate the flywires
|
| /Zephyr-latest/cmake/toolchain/oneApi/ |
| D | generic.cmake | 46 set(TOOLCHAIN_HAS_NEWLIB OFF CACHE BOOL "True if toolchain supports newlib")
|
| /Zephyr-latest/doc/_doxygen/ |
| D | mainpage.md | 15 The Zephyr kernel supports multiple architectures, including ARM
|
| /Zephyr-latest/drivers/led/ |
| D | Kconfig.ht16k33 | 13 controller driver. The controller supports up to 128 LEDs
|
| /Zephyr-latest/samples/drivers/misc/ft800/ |
| D | README.rst | 25 supports Arduino shields.
|
| /Zephyr-latest/boards/nxp/frdm_mcxn236/ |
| D | frdm_mcxn236.dts | 72 * LPFLEXCOMM supports UART and I2C on the same instance, enable this for
|
| /Zephyr-latest/boards/nxp/lpcxpresso55s28/ |
| D | Kconfig.defconfig | 39 # Board only supports MCUBoot via "upgrade only" method:
|
| /Zephyr-latest/drivers/display/ |
| D | Kconfig.ili9xxx | 20 API only supports RGB565 mode.
|
| /Zephyr-latest/drivers/mdio/ |
| D | Kconfig | 22 The MDIO shell currently supports scanning and device
|
| /Zephyr-latest/samples/drivers/ht16k33/ |
| D | README.rst | 11 driver. The sample supports up to 128 LEDs connected to the
|
| /Zephyr-latest/samples/subsys/mgmt/osdp/ |
| D | README.rst | 8 It supports Secure Channel (SC) for encrypted and authenticated communication
|
12345678910>>...30
