Searched refs:speed (Results 1 – 12 of 12) sorted by relevance
| /hal_infineon-3.4.0/mtb-pdl-cat1/drivers/source/ |
| D | cy_seglcd.c | 84 #define CY_SEGLCD_IS_SPEED_VALID(speed) ((CY_SEGLCD_SPEED_LOW == (speed)) || \ argument
85 (CY_SEGLCD_SPEED_HIGH == (speed)))
93 …define CY_SEGLCD_IS_BIAS_4_5_SUPPORTED(base,speed) ((CY_SEGLCD_REV_1(base)) ? (CY_SEGLCD_SPEED_HIG… argument
95 #define CY_SEGLCD_IS_BIAS_VALID(base,bias,speed) ((CY_SEGLCD_BIAS_HALF == (bias)) || \ argument
97 (CY_SEGLCD_IS_BIAS_4_5_SUPPORTED(base,speed) && (CY_SEGLCD_BIAS_FOURTH == (bias))) || \
98 (CY_SEGLCD_IS_BIAS_4_5_SUPPORTED(base,speed) && (CY_SEGLCD_BIAS_FIFTH == (bias))))
384 CY_ASSERT_L3(CY_SEGLCD_IS_SPEED_VALID(config->speed)); in Cy_SegLCD_Init()
387 CY_ASSERT_L3(CY_SEGLCD_IS_BIAS_VALID (base, config->bias, config->speed)); in Cy_SegLCD_Init()
394 …uint32_t locCheck = ((CY_SEGLCD_SPEED_LOW == config->speed) && (CY_SEGLCD_REV_1(base))) ? (CY_SEGL… in Cy_SegLCD_Init()
409 LCD_CONTROL(base) = _VAL2FLD(LCD_CONTROL_LCD_MODE, config->speed) | in Cy_SegLCD_Init()
|
| /hal_infineon-3.4.0/XMCLib/drivers/inc/ |
| D | xmc_eth_phy.h | 96 XMC_ETH_LINK_SPEED_t speed; /**< ETH speed: 100M or 10M? */ member
|
| D | xmc_eth_mac.h | 1274 XMC_ETH_LINK_SPEED_t speed, in XMC_ETH_MAC_SetLink() argument
1279 (uint32_t)speed | (uint32_t)duplex; in XMC_ETH_MAC_SetLink()
|
| D | xmc_usbh.h | 248 uint32_t speed : 2; /**< USB Host Port speed setting (ARM_USB_SPEED_xxx) */ member
|
| D | xmc_usbd.h | 346 uint32_t speed : 2; /**< USB Device speed */ member
|
| D | xmc_usbd_regs.h | 1850 uint8_t speed; /**< Device Speed 0: Unknown, 1: LS, 2:FS, 3: HS */ member
|
| /hal_infineon-3.4.0/XMCLib/drivers/src/ |
| D | xmc_eth_phy_ksz8031rnl.c | 156 if (config->speed == XMC_ETH_LINK_SPEED_100M) in XMC_ETH_PHY_Init()
|
| D | xmc_eth_phy_ksz8081rnb.c | 156 if (config->speed == XMC_ETH_LINK_SPEED_100M) in XMC_ETH_PHY_Init()
|
| D | xmc_eth_phy_dp83848.c | 173 if (config->speed == XMC_ETH_LINK_SPEED_100M) in XMC_ETH_PHY_Init()
|
| D | xmc_usbh.c | 702 port_state.speed = XMC_USBH_SPEED_FULL; in XMC_USBH_PortGetState()
|
| D | xmc_usbd.c | 1243 state.speed = XMC_USBD_SPEED_FULL; in XMC_USBD_DeviceGetState()
|
| /hal_infineon-3.4.0/mtb-pdl-cat1/drivers/include/ |
| D | cy_seglcd.h | 461 cy_en_seglcd_speed_t speed; /**< Speed mode selection, see: #cy_en_seglcd_speed_t. */ member
|
