| /Zephyr-latest/scripts/west_commands/runners/ |
| D | probe_rs.py | 15 erase=False, argument
20 self.erase = erase
40 erase=True,
64 erase=args.erase,
74 if self.erase:
|
| D | nrfjprog.py | 20 def __init__(self, cfg, family, softreset, dev_id, erase=False, argument
24 super().__init__(cfg, family, softreset, dev_id, erase, reset,
40 args.dev_id, erase=args.erase,
79 erase = _op['chip_erase_mode']
80 if erase == 'ERASE_ALL':
82 elif erase == 'ERASE_PAGES':
84 elif erase == 'ERASE_PAGES_INCLUDING_UICR':
86 elif erase == 'NO_ERASE':
|
| D | minichlink.py | 19 erase: bool,
27 self.erase = erase
38 return RunnerCaps(commands={"flash"}, flash_addr=True, erase=True, reset=True)
58 erase=args.erase,
77 if self.erase:
|
| D | ezflashcli.py | 15 def __init__(self, cfg, tool, dev_id=None, tool_opt=None, erase=False, reset=True): argument
21 self.erase = bool(erase)
35 return RunnerCaps(commands={'flash'}, dev_id=True, tool_opt=True, erase=True, reset=True)
56 tool_opt=args.tool_opt, erase=args.erase)
77 if self.erase:
|
| D | silabs_commander.py | 21 def __init__(self, cfg, device, dev_id, commander, dt_flash, erase, speed, tool_opt): argument
32 self.erase = erase
46 dev_id=True, flash_addr=True, erase=True,
77 erase=args.erase,
85 if self.erase:
|
| D | spi_burn.py | 16 def __init__(self, cfg, addr, spiburn, iceman, timeout, gdb_port, gdb_ex, erase=False): argument
23 self.erase = bool(erase)
33 return RunnerCaps(commands={'flash', 'debug'}, erase=True, flash_addr=True)
68 cfg, address, spiburn, iceman, args.timeout, args.gdb_port, args.gdb_ex, args.erase
117 if self.erase:
|
| D | esp32.py | 19 app_address, erase=False, reset=False, baud=921600, argument
26 self.erase = bool(erase)
47 return RunnerCaps(commands={'flash'}, erase=True, reset=True)
97 app_address=args.esp_app_address, erase=args.erase, reset=args.reset,
113 if self.erase is True:
|
| D | bossac.py | 28 speed=DEFAULT_BOSSAC_SPEED, boot_delay=0, erase=False): argument
34 self.erase = erase
42 return RunnerCaps(commands={'flash'}, erase=True)
64 boot_delay=args.delay, erase=args.erase)
187 if self.erase:
|
| D | linkserver.py | 26 dt_flash=True, erase=True, argument
44 self.erase = erase
65 dev_id=True, flash_addr=True, erase=True,
102 erase=args.erase,
192 if self.erase:
|
| D | pyocd.py | 21 dev_id=None, flash_addr=0x0, erase=False, flash_opts=None, argument
38 self.erase = erase
80 dev_id=True, flash_addr=True, erase=True,
124 flash_addr=flash_addr, erase=args.erase, flash_opts=args.flash_opt,
165 erase_method = 'chip' if self.erase else 'sector'
|
| /Zephyr-latest/samples/subsys/nvs/ |
| D | CMakeLists.txt | 6 board_runner_args(dfu-util "--dfuse-modifiers=force:mass-erase")
7 board_runner_args(pyocd "--erase")
8 board_runner_args(nrfjprog "--erase")
|
| /Zephyr-latest/drivers/flash/ |
| D | Kconfig.simulator | 26 bool "Program-erase device"
30 Explicit erase (non-erase-on-write) Flash, which is device that requires erase
31 to erase-value prior to write as it only allows to change bits from erase-value
46 Keep in mind that write operations can only change value of a bit from erase-value to the
50 but only change from erase-value to opposite will be registered.
68 int "Minimum erase time (µS)"
|
| D | Kconfig | 23 Device does not do erase-on-write (erase-on-program, auto-erase
24 on write) and requires explicit erase procedure to be programmed
28 All pure Flash devices are evolution of EEPROM where erase has
29 been separated from write, EEPROM has erase-on-write, giving
30 it advantage of higher write speeds at a cost of larger erase block.
31 Note that explicit-erase capability does not warrants that
32 write without erase is not allowed, taking the above restrictions,
34 erase.
48 Device does not require explicit erase before programming
51 Note that the device may have erase-on-write (auto-erase),
[all …]
|
| D | Kconfig.nrf | 49 bool "Nordic nRFx flash driver partial erase"
52 Enable partial erase feature. Partial erase is performed in time
55 This allows interrupting flash erase between operations
57 This feature may also be used for better syncing flash erase
62 int "Partial erase timeout in MS"
66 This is maximum time, in ms, that NVMC will use to erase part
78 to the flash erase and write operations timeout. The base for
|
| /Zephyr-latest/tests/drivers/flash_simulator/flash_sim_impl/boards/ |
| D | native_ev_0x00.overlay | 8 erase-value = < 0x00 >;
12 erase-block-size = <1024>;
|
| /Zephyr-latest/tests/subsys/llext/boards/ |
| D | qemu_arc_qemu_arc_em.overlay | 7 erase-value = <0x00>;
13 erase-block-size = <1024>;
|
| D | qemu_cortex_a9.overlay | 7 erase-value = <0x00>;
13 erase-block-size = <1024>;
|
| D | qemu_cortex_r5.overlay | 7 erase-value = <0x00>;
13 erase-block-size = <1024>;
|
| /Zephyr-latest/boards/common/ |
| D | openocd.board.cmake | 6 # "load_image" or "flash write_image erase"?
13 set_ifndef(OPENOCD_FLASH "flash write_image erase")
|
| /Zephyr-latest/dts/arm/gd/gd32l23x/ |
| D | gd32l233rc.dtsi | 36 /* GD32L23X DataSheet not defined the maximum page erase time
40 * Assume GD32L23X use the worst implementation, set the max erase
43 max-erase-time-ms = <1200>;
|
| /Zephyr-latest/tests/drivers/flash_simulator/flash_sim_reboot/boards/ |
| D | mps2_an385.overlay | 16 erase-value = <0xff>;
23 erase-block-size = <1024>;
|
| /Zephyr-latest/subsys/mgmt/mcumgr/grp/zephyr_basic/ |
| D | Kconfig | 12 bool "Storage erase command"
15 Enables command that allows to erase storage partition.
|
| /Zephyr-latest/dts/arm/renesas/ra/ra8/ |
| D | r7fa8m1ahecbd.dtsi | 16 erase-block-size = <8192>;
24 erase-block-size = <64>;
|
| D | r7fa8t1ahecbd.dtsi | 16 erase-block-size = <8192>;
24 erase-block-size = <64>;
|
| D | r7fa8d1bhecbd.dtsi | 17 erase-block-size = <8192>;
25 erase-block-size = <64>;
|
