Searched refs:UP (Results 1 – 25 of 26) sorted by relevance
12
| /Zephyr-latest/boards/up-bridge-the-gap/up_squared_pro_7000/doc/ |
| D | up_squared_pro_7000.rst | 5 UP Squared Pro 7000
11 UP Squared Pro 7000 is the 3rd generation of palm-sized developer board of
12 UP Boards series. UP Squared Pro 7000 is powered by Intel Alder Lake N
18 This board configuration enables kernel support for the UP Squared Pro 7000 boards.
23 General information about the board can be found at the `UP Squared Pro 7000`_ website.
28 Refer to the `UP Squared Pro 7000`_ website for more information.
33 Use the following procedures for booting an image for an UP Squared Pro 7000 board.
44 application for UP Squared Pro 7000 board:
63 Refer to `UP Serial Console`_ for additional information about serial
66 Booting the UP Squared Pro 7000 Board using UEFI
[all …]
|
| /Zephyr-latest/boards/up-bridge-the-gap/up_squared/doc/ |
| D | index.rst | 3 UP Squared
9 UP |sup2| (UP Squared) is an ultra compact single board computer with high
16 :alt: UP Squared
20 This board configuration enables kernel support for the `UP Squared`_ board.
23 This board configuration works on all three variants of `UP Squared`_
30 General information about the board can be found at the `UP Squared`_ website.
50 Refer to the `UP Squared`_ website and `UP Squared Pinout`_ website
56 Use the following procedures for booting an image on a UP Squared board.
67 application on UP Squared:
79 Booting the UP Squared Board using UEFI
[all …]
|
| /Zephyr-latest/samples/basic/servo_motor/src/ |
| D | main.c | 24 UP, enumerator
30 enum direction dir = UP; in main()
49 dir = UP; in main()
|
| /Zephyr-latest/boards/up-bridge-the-gap/ |
| D | index.rst | 3 UP Bridge the Gap.
|
| /Zephyr-latest/boards/up-bridge-the-gap/up_squared_pro_7000/ |
| D | up_squared_pro_7000.dts | 10 model = "UP Squared Pro 7000 board";
|
| /Zephyr-latest/ |
| D | .ruff.toml | 17 "UP", # pyupgrade
|
| /Zephyr-latest/samples/net/capture/ |
| D | README.rst | 55 zeth: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
64 zeth-ip6ip: flags=209<UP,POINTOPOINT,RUNNING,NOARP> mtu 1480
73 zeth-ip6ip6: flags=209<UP,POINTOPOINT,RUNNING,NOARP> mtu 1452
82 zeth-ipip: flags=209<UP,POINTOPOINT,RUNNING,NOARP> mtu 1480
91 zeth-ipip6: flags=209<UP,POINTOPOINT,RUNNING,NOARP> mtu 1452
168 The tunneling interface will be UP and the captured packets will be sent to
|
| /Zephyr-latest/boards/arduino/nano_33_ble/support/ |
| D | startup.cmm | 99 SYStem.UP
|
| /Zephyr-latest/doc/connectivity/networking/ |
| D | eth_bridge_native_sim_setup.rst | 34 zeth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
44 zeth1: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
|
| /Zephyr-latest/boards/waveshare/open103z/ |
| D | waveshare_open103z.dts | 62 label = "User joystick UP";
|
| /Zephyr-latest/boards/shields/inventek_eswifi/doc/ |
| D | index.rst | 50 recommendation is bend the NRST pin and make a wire to D6. WAKE-UP signal is
74 | D7 | WAKE-UP | UART/SPI [wiring] |
|
| /Zephyr-latest/boards/intel/adsp/doc/ |
| D | intel_adsp_generic.rst | 28 The Intel `UP Xtreme`_ product line has the publicly
30 `UP Xtreme i11-0001 series`_ (:ref:`intel_adsp_cavs25`) board as an example.
54 UP Xtreme users can refer to the `UP Community wiki`_ for help installing a
|
| /Zephyr-latest/boards/st/b_g474e_dpow1/doc/ |
| D | index.rst | 89 - LED (UP RED) : PB5
|
| /Zephyr-latest/boards/st/stm32h747i_disco/doc/ |
| D | index.rst | 108 - W-UP : PC13
113 - J-UP : PK6
|
| /Zephyr-latest/boards/snps/em_starterkit/doc/ |
| D | index.rst | 187 switches should be UP except for switch 1. Other configuration choices
189 all dip switches should be UP except for switch 2. Next press the button
|
| /Zephyr-latest/doc/hardware/pinctrl/ |
| D | index.rst | 92 | | - Pull: UP | | - Pull: NONE |
|
| /Zephyr-latest/dts/bindings/ |
| D | vendor-prefixes.txt | 701 up-bridge-the-gap UP Bridge the Gap
|
| /Zephyr-latest/doc/releases/ |
| D | release-notes-2.5.rst | 1042 * :github:`31696` - UP² Celeron version (not the Atom one) has no console
1111 * :github:`31517` - UP² broken (git bisect findings inside)
1513 * :github:`29367` - usb: drivers: add USB support for UP squared
|
| D | release-notes-1.13.rst | 61 * x86: add support for UP Squared (Pentium/Celeron)
|
| D | release-notes-3.0.rst | 986 * :github:`41835` - UP squared and acrn_ehl_crb: test cases which have config SMP config failed
|
| D | release-notes-3.2.rst | 228 * Added support of non-multithreading mode for all UP ARC targets.
418 * Added support for qemu_arc_hs5x board (ARCv3, 32bit, UP, HS5x)
|
| D | release-notes-2.3.rst | 1281 * :github:`21156` - Interrupts do not work on UP Squared board
|
| D | release-notes-3.3.rst | 3550 * :github:`49451` - Treat carrier UP/DOWN independently to interface UP/DOWN
|
| D | release-notes-2.0.rst | 375 * By default a network interface is set to UP when the device starts.
|
| D | release-notes-3.1.rst | 324 * Added ARCv3 32 bit (HS5x) support - both GNU and MWDT toolchains, both UP and SMP
|
12
