| /Zephyr-latest/tests/drivers/gpio/gpio_basic_api/src/ |
| D | test_callback_trigger.c | 26 && (dd->mode == GPIO_INT_EDGE_BOTH)) { in callback()
93 if (mode == GPIO_INT_EDGE_BOTH) { in test_callback()
141 zassert_equal(test_callback(GPIO_INT_EDGE_BOTH), TC_PASS, in ZTEST()
|
| D | test_config_trigger.c | 43 ret = gpio_pin_interrupt_configure(dev_in, PIN_IN, GPIO_INT_EDGE_BOTH); in ZTEST()
94 ret = gpio_pin_interrupt_configure(dev_in, PIN_IN, GPIO_INT_EDGE_BOTH); in ZTEST()
|
| /Zephyr-latest/samples/boards/bbc/microbit/line_follower_robot/src/ |
| D | main.c | 115 gpio_pin_interrupt_configure_dt(&left_gpio, GPIO_INT_EDGE_BOTH); in main()
116 gpio_pin_interrupt_configure_dt(&right_gpio, GPIO_INT_EDGE_BOTH); in main()
|
| /Zephyr-latest/samples/sensor/sm351lt/src/ |
| D | main.c | 60 .val1 = GPIO_INT_EDGE_BOTH, in main()
|
| /Zephyr-latest/drivers/sensor/ti/ina23x/ |
| D | ina230_trigger.c | 76 GPIO_INT_EDGE_BOTH); in ina230_trigger_mode_init()
|
| /Zephyr-latest/drivers/input/ |
| D | input_gpio_keys.c | 159 ret = gpio_pin_interrupt_configure_dt(gpio_spec, GPIO_INT_EDGE_BOTH); in gpio_keys_interrupt_configure()
270 ret = gpio_pin_interrupt_configure_dt(gpio, GPIO_INT_EDGE_BOTH); in gpio_keys_pm_action()
|
| D | input_gpio_qdec.c | 67 gpio_flags_t flags = enable ? GPIO_INT_EDGE_BOTH : GPIO_INT_DISABLE; in gpio_qdec_irq_setup()
|
| /Zephyr-latest/drivers/power_domain/ |
| D | power_domain_gpio_monitor.c | 113 rc = gpio_pin_interrupt_configure_dt(&config->power_good_gpio, GPIO_INT_EDGE_BOTH); in pd_gpio_monitor_init()
|
| /Zephyr-latest/drivers/sensor/hc_sr04/ |
| D | hc_sr04.c | 125 ret = gpio_pin_interrupt_configure_dt(&cfg->echo_gpios, GPIO_INT_EDGE_BOTH); in hcsr04_sample_fetch()
|
| /Zephyr-latest/drivers/gpio/ |
| D | gpio_mchp_mss.c | 166 case GPIO_INT_EDGE_BOTH: in mss_gpio_pin_interrupt_configure()
|
| D | gpio_iproc.c | 138 if (trig & GPIO_INT_EDGE_BOTH) { in gpio_iproc_pin_interrupt_configure()
|
| D | gpio_andes_atcgpio100.c | 228 case GPIO_INT_EDGE_BOTH: in gpio_atcgpio100_pin_interrupt_configure()
|
| D | gpio_emul.c | 223 case GPIO_INT_EDGE_BOTH: in gpio_emul_gen_interrupt_bits()
|
| /Zephyr-latest/drivers/sensor/ti/tmp1075/ |
| D | tmp1075.c | 192 result = gpio_pin_interrupt_configure_dt(alert_gpio, GPIO_INT_EDGE_BOTH); in setup_interrupts()
|
| /Zephyr-latest/tests/drivers/gpio/gpio_api_1pin/src/ |
| D | test_pin_interrupt.c | 223 test_gpio_pin_interrupt_edge(0, GPIO_INT_EDGE_BOTH); in ZTEST()
|
| /Zephyr-latest/drivers/sensor/ti/tmp108/ |
| D | tmp108.c | 352 GPIO_INT_EDGE_BOTH); in setup_interrupts()
|
| /Zephyr-latest/subsys/mgmt/ec_host_cmd/backends/ |
| D | ec_host_cmd_backend_spi_stm32.c | 774 gpio_pin_interrupt_configure(hc_spi->cs.port, hc_spi->cs.pin, GPIO_INT_EDGE_BOTH); in ec_host_cmd_spi_init()
844 gpio_pin_interrupt_configure_dt(&hc_spi->cs, GPIO_INT_EDGE_BOTH); in ec_host_cmd_spi_stm32_pm_action()
|
| /Zephyr-latest/samples/boards/phytec/reel_board/mesh_badge/src/ |
| D | reel_board.c | 514 gpio_pin_interrupt_configure_dt(&sw0_gpio, GPIO_INT_EDGE_BOTH); in configure_button()
|
| /Zephyr-latest/drivers/sensor/st/lis2dh/ |
| D | lis2dh_trigger.c | 22 GPIO_INT_EDGE_BOTH,
|
| /Zephyr-latest/drivers/disk/ |
| D | sdmmc_stm32.c | 624 err = gpio_pin_interrupt_configure_dt(&priv->cd, GPIO_INT_EDGE_BOTH); in stm32_sdmmc_card_detect_init()
|
| /Zephyr-latest/tests/drivers/gpio/gpio_ite_it8xxx2_v2/src/ |
| D | main.c | 222 zassert_ok(gpio_pin_interrupt_configure(gpio_dev, TEST_PIN, GPIO_INT_EDGE_BOTH)); in ZTEST()
|
| /Zephyr-latest/include/zephyr/drivers/ |
| D | gpio.h | 175 #define GPIO_INT_EDGE_BOTH (GPIO_INT_ENABLE | \ macro
|
| /Zephyr-latest/drivers/modem/ |
| D | hl7800.c | 6466 ret = gpio_pin_interrupt_configure_dt(&hl7800_cfg.gpio[MDM_VGPIO], GPIO_INT_EDGE_BOTH); in hl7800_init()
6481 ret = gpio_pin_interrupt_configure_dt(&hl7800_cfg.gpio[MDM_UART_DSR], GPIO_INT_EDGE_BOTH); in hl7800_init()
6496 ret = gpio_pin_interrupt_configure_dt(&hl7800_cfg.gpio[MDM_GPIO6], GPIO_INT_EDGE_BOTH); in hl7800_init()
6511 ret = gpio_pin_interrupt_configure_dt(&hl7800_cfg.gpio[MDM_UART_CTS], GPIO_INT_EDGE_BOTH); in hl7800_init()
|
| /Zephyr-latest/doc/releases/ |
| D | release-notes-3.0.rst | 1258 …601` - On ESP32S2 platform GPIO interrupt causes RTOS to hang when configured to GPIO_INT_EDGE_BOTH
|
