Searched refs:activity (Results 1 – 25 of 35) sorted by relevance
12
| /Zephyr-Core-3.7.0/drivers/sensor/adi/adxl372/ |
| D | Kconfig | 43 Threshold for activity detection.
46 int "In-activity threshold in mg"
50 Threshold for in-activity detection.
57 The activity timer implements a robust activity detection that
59 only sustained motion can trigger activity detection.
60 Number of multiples of 3.3 ms activity timer for which above threshold
61 acceleration is required to detect activity. It is 3.3 ms per code
65 int "In-activity time"
76 bool "Use referenced activity/in-activity detection"
80 When using absolute activity detection, acceleration samples are
[all …]
|
| /Zephyr-Core-3.7.0/drivers/sensor/adi/adxl367/ |
| D | Kconfig | 34 Threshold for activity detection.
37 int "In-activity threshold in raw value"
41 Threshold for in-activity detection.
48 The activity timer implements a robust activity detection that
50 only sustained motion can trigger activity detection. Value is the
55 int "In-activity time"
65 bool "Use activity detection"
78 bool "Use referenced activity detection"
82 When using absolute activity detection, acceleration samples are
|
| /Zephyr-Core-3.7.0/drivers/sensor/adi/adxl362/ |
| D | Kconfig | 104 compared to in activity trigger mode.
110 8 bit value written to the activity timer register
124 16 bit value written to the activity timer register
|
| /Zephyr-Core-3.7.0/drivers/sensor/bosch/bma4xx/ |
| D | Kconfig | 24 extra bus activity and increases code size.
|
| /Zephyr-Core-3.7.0/doc/develop/test/ |
| D | bsim.rst | 18 When there is radio activity, this Linux executable will connect to the BabbleSim Phy simulation
32 Tests without radio activity: bsim tests with twister
35 The :ref:`bsim boards<bsim boards>` can be used without radio activity, and in that case, it is not
40 Tests with radio activity
43 When there is radio activity, BabbleSim tests require at the very least a physical layer simulation
191 simulation segment, ensuring that the radio activity of each segment can be inspected a
|
| /Zephyr-Core-3.7.0/drivers/sensor/st/iis2dlpc/ |
| D | Kconfig | 67 Enable activity/inactivity detection
|
| /Zephyr-Core-3.7.0/subsys/bluetooth/controller/coex/ |
| D | readme.rst | 8 …istence interface, which allows the Bluetooth controller to suspend its activity until the other t…
|
| /Zephyr-Core-3.7.0/boards/seagate/faze/doc/ |
| D | index.rst | 36 - 1 white LED (SSD activity blinking).
92 | PIO1_23 | GPIO | SSD activity white LED |
|
| /Zephyr-Core-3.7.0/tests/net/lib/mqtt_packet/ |
| D | README | 5 No network activity is involved in this test, so ** theoretically **
|
| /Zephyr-Core-3.7.0/boards/seagate/faze/ |
| D | faze.dts | 50 label = "SSD activity LED";
|
| /Zephyr-Core-3.7.0/samples/net/sockets/echo_service/ |
| D | README.rst | 15 one thread, and which can then trigger a callback if there is activity in the set
|
| /Zephyr-Core-3.7.0/boards/native/nrf_bsim/doc/ |
| D | nrf52_bsim.rst | 18 This uses `BabbleSim`_ to simulate the radio activity, and the
117 is possible only while there is no radio activity. But is perfectly fine for
120 When you want to run a simulation with radio activity you need to run also the
|
| D | nrf54l15bsim.rst | 18 This uses `BabbleSim`_ to simulate the radio activity, and the
|
| D | nrf5340bsim.rst | 18 These use `BabbleSim`_ to simulate the radio activity, and the
|
| /Zephyr-Core-3.7.0/subsys/net/lib/lwm2m/ |
| D | Kconfig.ucifi | 15 level and activity.
|
| /Zephyr-Core-3.7.0/drivers/i2c/ |
| D | i2c_dw_registers.h | 80 uint32_t activity : 1 __packed; member
|
| /Zephyr-Core-3.7.0/samples/boards/stm32/power_mgmt/serial_wakeup/ |
| D | README.rst | 25 that can be requested dynamically by device on activity detection (HSI on STM32WB).
|
| /Zephyr-Core-3.7.0/boards/seagate/legend/ |
| D | legend.dts | 158 * The maximum period needed on Legend devices for activity LED
|
| /Zephyr-Core-3.7.0/samples/boards/nrf/mesh/onoff-app/ |
| D | README.rst | 16 corresponding LED and does not initiate any mesh activity.
|
| /Zephyr-Core-3.7.0/boards/adi/eval_adin2111ebz/doc/ |
| D | index.rst | 26 activity status indication for each port.
|
| /Zephyr-Core-3.7.0/boards/native/doc/ |
| D | bsim_boards_design.rst | 220 Use of babblesim components: tracing, random number generation, logging activity
227 handled over the bsim libPhyCom libraries. For the radio activity the figure
|
| /Zephyr-Core-3.7.0/boards/st/nucleo_u575zi_q/doc/ |
| D | index.rst | 120 sound-activity detection
|
| /Zephyr-Core-3.7.0/boards/st/nucleo_u5a5zj_q/doc/ |
| D | index.rst | 152 with sound-activity detection
|
| /Zephyr-Core-3.7.0/doc/connectivity/networking/api/ |
| D | http_server.rst | 20 background thread. The application can control the server activity with
|
| /Zephyr-Core-3.7.0/boards/st/sensortile_box_pro/doc/ |
| D | index.rst | 133 sound-activity detection
|
12
