Searched full:unsure (Results 1 – 25 of 34) sorted by relevance
12
| /Zephyr-latest/subsys/net/lib/trickle/ |
| D | Kconfig | 10 so say 'n' if unsure.
|
| /Zephyr-latest/samples/sensor/bme280/ |
| D | arduino_i2c.overlay | 11 * address; check your device documentation if unsure.
|
| /Zephyr-latest/samples/drivers/led/is31fl3216a/boards/ |
| D | arduino_i2c.overlay | 11 * address; check your device documentation if unsure.
|
| /Zephyr-latest/drivers/gpio/ |
| D | Kconfig.intel | 23 Say y if unsure.
|
| D | Kconfig.emul | 19 If unsure, say N.
|
| /Zephyr-latest/subsys/mem_mgmt/ |
| D | Kconfig | 12 unsure to save RODATA space.
|
| /Zephyr-latest/drivers/dma/ |
| D | Kconfig.xilinx_axi_dma | 21 coherency for DMA accesses. If you are unsure whether you need this feature,
53 This is the safest option and the default, select this if you are unsure.
|
| /Zephyr-latest/drivers/reset/ |
| D | Kconfig | 25 initialized earlier in the startup cycle. If unsure, leave at default
|
| /Zephyr-latest/samples/sensor/tdk_apex/boards/ |
| D | nrf52dk_nrf52832_i2c.overlay | 20 * address; check your device documentation if unsure.
|
| /Zephyr-latest/dts/bindings/dai/ |
| D | nxp,dai-esai.yaml | 49 instead of this value so use with caution. If unsure, it's better to
67 If unsure, don't specify this property at all. By default, all pins will
|
| /Zephyr-latest/drivers/syscon/ |
| D | Kconfig | 38 initialized earlier in the startup cycle. If unsure, leave at default
|
| /Zephyr-latest/samples/sensor/6dof_motion_drdy/boards/ |
| D | nrf52dk_nrf52832_i2c.overlay | 20 * address; check your device documentation if unsure.
|
| /Zephyr-latest/drivers/i3c/ |
| D | Kconfig | 34 Says Y if unsure.
47 Says Y if unsure.
|
| /Zephyr-latest/drivers/timer/ |
| D | Kconfig.gecko | 33 If unsure, say 'N'.
|
| /Zephyr-latest/dts/bindings/spi/ |
| D | spi-controller.yaml | 52 If unsure about the flags cell, GPIO_ACTIVE_LOW is generally a safe
|
| /Zephyr-latest/dts/bindings/mspi/ |
| D | mspi-controller.yaml | 87 If unsure about the flags cell, GPIO_ACTIVE_LOW is generally a safe
|
| /Zephyr-latest/subsys/net/ip/ |
| D | Kconfig.stats | 9 Manage statistics accounting. This takes memory so say 'n' if unsure.
|
| D | icmpv6.h | 182 * and code this gives extra information to the recipient. Set 0 if unsure
|
| /Zephyr-latest/samples/bluetooth/direction_finding_central/ |
| D | README.rst | 22 unsure.
|
| /Zephyr-latest/samples/bluetooth/direction_finding_connectionless_rx/ |
| D | README.rst | 22 unsure.
|
| /Zephyr-latest/samples/bluetooth/direction_finding_peripheral/ |
| D | README.rst | 21 unsure.
|
| /Zephyr-latest/samples/bluetooth/direction_finding_connectionless_tx/ |
| D | README.rst | 21 unsure.
|
| /Zephyr-latest/dts/bindings/net/wireless/ |
| D | nordic,nrf21540-fem.yaml | 59 'ant-sel-gpios', and 'mode-gpios' properties. If unsure about the
|
| /Zephyr-latest/ |
| D | Kconfig.zephyr | 113 If unsure, leave at the default value 0.
126 If unsure, leave at the default value 0.
154 If unsure, leave at the default value 0.
238 If unsure, leave at the default value 0.
288 If unsure, say Y.
|
| /Zephyr-latest/scripts/support/ |
| D | quartus-flash.py | 128 "USB-BlasterII. Run jtagconfig -n if unsure.",
|
12
