Searched full:tune (Results 1 – 25 of 32) sorted by relevance
12
| /Zephyr-latest/dts/bindings/i2c/ |
| D | atmel,sam-i2c-twim.yaml | 31 For best performances, user can tune the slope curves using an osciloscope.
34 high speed mode. The tune should be performed for both clock and data lines
59 std-clk-strength-low to fine tune the TWCK slope.
89 std-data-strength-low to fine tune the TWD slope.
120 hs-clk-strength-low to fine tune the TWCK slope.
164 should be adjusted with hs-data-strength-low to fine tune the TWD
|
| /Zephyr-latest/dts/bindings/clock/ |
| D | nordic,nrf-auxpll.yaml | 71 nordic,current-tune:
74 description: Constant current tune for the ring oscillator
|
| /Zephyr-latest/drivers/adc/ |
| D | Kconfig.tla202x | 21 Fine tune the priority for the driver initialization. Make sure it's
|
| /Zephyr-latest/drivers/timer/ |
| D | Kconfig.riscv_machine | 39 dt_node_int_prop_int from Kconfig. (Tune in the conf file is not preferable.)
|
| /Zephyr-latest/dts/bindings/timer/ |
| D | st,stm32-lptim.yaml | 32 CONFIG_SYS_CLOCK_TICKS_PER_SEC could be used to tune tick duration and gain precision,
|
| /Zephyr-latest/arch/arm64/core/ |
| D | CMakeLists.txt | 57 zephyr_cc_option(-moverride=tune=no_ldp_stp_qregs)
|
| /Zephyr-latest/samples/bluetooth/central_hr/ |
| D | prj_minimal.conf | 42 # In order to correctly tune the stack sizes for the threads the following
|
| /Zephyr-latest/samples/bluetooth/peripheral_hr/ |
| D | prj_minimal.conf | 48 # In order to correctly tune the stack sizes for the threads the following
|
| /Zephyr-latest/drivers/entropy/ |
| D | entropy_cc13xx_cc26xx.c | 52 /* De-tune FROs */ in start_trng()
87 /* De-tune FROs */ in handle_shutdown_ovf()
|
| /Zephyr-latest/scripts/ci/es_upload/ |
| D | README.md | 22 Tune resulting data scheme and size depending on your particular needs.
|
| /Zephyr-latest/soc/silabs/ |
| D | Kconfig | 194 in Silicon Labs HAL. These routines initialize and tune HFXOs,
|
| /Zephyr-latest/samples/net/cloud/aws_iot_mqtt/ |
| D | README.rst | 60 Additionnaly, it is possible to tune the firmware to pass the AWS DQP test
|
| /Zephyr-latest/doc/kernel/memory_management/ |
| D | virtual_memory.rst | 6 Virtual memory (VM) in Zephyr provides developers with the ability to fine tune
|
| /Zephyr-latest/boards/snps/nsim/arc_classic/doc/ |
| D | index.rst | 288 DSP or FPU. Instead we prefer to fine-tune the HW features usage which (with all its pros)
310 and fine-tune MDB behavior on multi-core systems.
|
| /Zephyr-latest/scripts/west_commands/runners/ |
| D | bossac.py | 174 the USB device again. This function lets users tune a magic
|
| /Zephyr-latest/boards/snps/nsim/arc_v/doc/ |
| D | index.rst | 152 DSP or FPU. Instead we prefer to fine-tune the HW features usage which (with all its pros)
|
| /Zephyr-latest/include/zephyr/sys/ |
| D | spsc_pbuf.h | 256 * Function can be used to tune the buffer size. Feature is enabled by
|
| /Zephyr-latest/include/zephyr/drivers/ |
| D | sdhc.h | 386 * allows an application to request the SD host controller to tune the card.
|
| /Zephyr-latest/samples/subsys/mgmt/updatehub/ |
| D | README.rst | 141 make it work or tune communication.
|
| /Zephyr-latest/drivers/ieee802154/ |
| D | ieee802154_dw1000_regs.h | 1376 * Crystals may be trimmed using this register setting to tune out errors,
1424 /* On Wake-up load the LDO tune value. */
1561 /* This bit when set initiates a load of the LDO tune code */
|
| D | ieee802154_dw1000.c | 1252 * - When available, on wake-up load the LDO tune value in dwt_initialise_dev()
1398 /* Configure PLL2/RF PLL block CFG/TUNE (for a given channel) */ in dwt_configure_rf_phy()
|
| /Zephyr-latest/subsys/net/ip/ |
| D | Kconfig | 657 If enabled, then it is possible to fine-tune network packet pool
|
| /Zephyr-latest/drivers/dma/ |
| D | dma_iproc_pax_v1.c | 304 /* Tune RM control programming for 4 rings */ in rm_cfg_start()
|
| /Zephyr-latest/drivers/sdhc/ |
| D | rcar_mmc.c | 338 /* tune if this reset isn't invoked during tuning */ in rcar_mmc_reset()
1605 * to tune the card.
|
| D | imx_usdhc.c | 764 LOG_DBG("Card failed to tune"); in imx_usdhc_request()
|
12
