Home
last modified time | relevance | path

Searched +full:termination +full:- +full:resistor (Results 1 – 6 of 6) sorted by relevance

/Zephyr-latest/tests/drivers/spi/spi_loopback/boards/
Ds32z2xxdc2_s32z270_dspi.overlay4 * SPDX-License-Identifier: Apache-2.0
11 output-enable;
12 nxp,current-reference-control;
13 nxp,termination-resistor;
17 input-enable;
18 nxp,current-reference-control;
19 nxp,termination-resistor;
25 pinctrl-0 = <&dspi0_default>;
26 pinctrl-names = "default";
30 compatible = "test-spi-loopback-slow";
[all …]
/Zephyr-latest/dts/bindings/pinctrl/
Dnxp,s32ze-pinctrl.yaml2 # SPDX-License-Identifier: Apache-2.0
20 #include <nxp/s32/S32Z27-BGA594-pinctrl.h>
26 output-enable;
30 input-enable;
40 'bias-pull-up' or 'slew-rate' that will be applied to all the pins defined in
41 'pinmux' array. To enable the input buffer use 'input-enable' and to enable the
42 output buffer use 'output-enable'.
44 To link the pin configurations with UART0 device, use pinctrl-N property in the
45 device node, where 'N' is the zero-based state index (0 is the default state).
49 pinctrl-0 = <&uart0_default>;
[all …]
/Zephyr-latest/dts/bindings/sensor/
Dmaxim,max17055.yaml4 # SPDX-License-Identifier: Apache-2.0
11 include: [sensor-device.yaml, i2c-device.yaml]
14 design-capacity:
19 design-voltage:
24 desired-voltage:
29 desired-charging-current:
34 i-chg-term:
37 description: The charge termination current in mA
39 rsense-mohms:
43 Value of Rsense resistor in milliohms (e.g. 5). It cannot be 0.
[all …]
/Zephyr-latest/include/zephyr/drivers/usb_c/
Dusbc_tc.h3 * SPDX-License-Identifier: Apache-2.0
8 * @brief USB Type-C Cable and Connector API used for USB-C drivers
10 * The information in this file was taken from the USB Type-C
18 * @brief USB Type-C
19 * @defgroup usb_type_c USB Type-C
32 * See Table 4-3 VBUS Sink Characteristics
38 * See Table 4-3 VBUS Sink Characteristics
45 * See Table 4-29 VBUS and VCONN Timing Parameters
52 * See Table 4-29 VBUS and VCONN Timing Parameters
58 * See Table 4-29 VBUS and VCONN Timing Parameters
[all …]
/Zephyr-latest/drivers/sensor/maxim/max17055/
Dmax17055.h4 * SPDX-License-Identifier: Apache-2.0
74 /* Value of Rsense resistor in milliohms (typically 5 or 10) */
84 /* The charge termination current in uA */
/Zephyr-latest/tests/drivers/can/host/
DREADME.rst9 This test suite uses `python-can`_ for testing Controller Area Network (CAN) communication between a
17 * The python-can library installed on the host PC.
25 the ``bitrate`` and ``bitrate-data`` CAN controller devicetree properties if needed. Default
29 The host end of the CAN fixture can be configured through python-can. Available configuration
30 options depend on the type of host CAN adapter used. The python-can library provides a lot of
31 flexibility for configuration as decribed in the `python-can configuration`_ page, all centered
35 * By default, the python-can configuration context is not specified, causing python-can to use the
38 ``:`` (i.e. specify fixture ``can:zcan0`` to use the ``zcan0`` python-can configuration context).
39 * The configuration context can be overridden using the ``--can-context`` test suite argument
40 (i.e. run ``twister`` with the ``--pytest-args=--can-context=zcan0`` argument to use the ``zcan0``
[all …]