Searched full:performed (Results 1 – 25 of 316) sorted by relevance
12345678910>>...13
| /Zephyr-latest/subsys/bluetooth/audio/ |
| D | csip_crypto.h | 39 * between the client and the server was performed.
41 * If the pairing was performed on Basic Rate/Enhanced Data Rate (BR/EDR), K is equal to the
45 * If the pairing was performed on Bluetooth Low Energy (LE), K is equal to the LTK shared by the
63 * between the client and the server was performed.
65 * If the pairing was performed on Basic Rate/Enhanced Data Rate (BR/EDR), K is equal to the
69 * If the pairing was performed on Bluetooth Low Energy (LE), K is equal to the LTK shared by the
|
| /Zephyr-latest/samples/drivers/led/pwm/ |
| D | Kconfig | 10 If set to 0, the short-cycle blinking demo will not be performed.
18 If set to 0, the long-cycle blinking demo will not be performed.
|
| /Zephyr-latest/samples/bluetooth/direct_adv/ |
| D | README.rst | 11 to the peripheral, casual advertising will be performed. Once bonded, on every subsequent
12 boot direct advertising to the bonded central will be performed. Additionally this sample
|
| /Zephyr-latest/samples/boards/nordic/nrfx_prs/ |
| D | README.rst | 21 - by pressing Button 1 user can request a transfer to be performed using the
26 is performed.
59 When no button is pressed, a background transfer on SPIM1 is performed.
|
| /Zephyr-latest/drivers/clock_control/ |
| D | Kconfig.nrf | 74 Enabling indicates that calibration is performed by the clock control driver.
87 Periodically, calibration action is performed. Action includes
101 reaches configured value then calibration is performed
117 Enables retrieving debug information like number of performed or
|
| D | Kconfig.stm32 | 76 Interval at which runtime measurements should be performed, in milliseconds
91 measurements - the result of a single measure performed at boot will be
|
| /Zephyr-latest/tests/subsys/sip_svc/ |
| D | Kconfig | 18 Number of iterations to be performed.
|
| /Zephyr-latest/drivers/sensor/bosch/bme280/ |
| D | Kconfig | 25 performed, whereas in forced mode only single measurement is performed.
|
| /Zephyr-latest/dts/bindings/power-domain/ |
| D | nxp,scu-pd.yaml | 17 performed.
|
| /Zephyr-latest/drivers/eeprom/ |
| D | Kconfig.eeprom_emu | 12 performed to the EEPROM is maximized by using a flash area that is
|
| /Zephyr-latest/drivers/usb_c/tcpc/ |
| D | Kconfig.tcpc_ps8xxx | 26 Number of initialization tries that will be performed
|
| D | Kconfig.tcpc_rt1715 | 26 Number of initialization tries that will be performed
|
| D | Kconfig.tcpc_tcpci | 20 Number of I2C transaction tries that will be performed for each request.
|
| /Zephyr-latest/dts/bindings/clock/ |
| D | st,stm32mp1-rcc.yaml | 7 On STM32MP1 platforms, clock control configuration is performed on A9 side.
|
| /Zephyr-latest/soc/nxp/mcx/mcxn/ |
| D | Kconfig.defconfig | 31 # so the PLL settings will not be performed in the driver.
|
| /Zephyr-latest/tests/drivers/clock_control/nrf_clock_calibration/src/ |
| D | test_nrf_clock_calibration.c | 82 /* Function pends until calibration counter is performed. When function leaves,
89 /* wait until calibration is performed. */ in sync_just_after_calibration()
95 /* Test checks if calibration and calibration skips are performed according
|
| /Zephyr-latest/include/zephyr/arch/common/ |
| D | pm_s2ram.h | 32 * cannot be performed a proper value is returned and the code must take care
74 * Function is used to determine if resuming after suspend-to-RAM shall be performed
|
| /Zephyr-latest/drivers/interrupt_controller/ |
| D | intc_system_apic.c | 68 * to the IRQ virtualization that is performed by this platform. See the
86 * to the IRQ virtualization that is performed by this platform. See the
|
| /Zephyr-latest/dts/bindings/sensor/ |
| D | aosong,dht.yaml | 23 Pin on which sensor communication will be performed.
|
| D | pixart,paa3905.yaml | 41 sequence is performed.
|
| /Zephyr-latest/samples/boards/st/power_mgmt/stm32wb_ble/ |
| D | README.rst | 13 After startup, a first 2 seconds beacon is performed, 1 second break and
|
| /Zephyr-latest/dts/bindings/i2c/ |
| D | atmel,sam-i2c-twim.yaml | 11 master capability is supported. Arbitration of the bus is performed
32 The tuning should be performed by groups defined <mode>-<line>. The prefix
34 high speed mode. The tune should be performed for both clock and data lines
|
| /Zephyr-latest/dts/bindings/input/ |
| D | zephyr,lvgl-button-input.yaml | 20 a click event will be performed at (120,220).
|
| /Zephyr-latest/arch/arm/core/mpu/ |
| D | arm_core_mpu_dev.h | 127 * The function shall assert if the operation cannot be not performed
161 * The function shall assert if the operation cannot be not performed
183 * The function shall assert if the operation cannot be not performed
203 * The function shall assert if the operation cannot be not performed
|
| /Zephyr-latest/arch/riscv/core/ |
| D | prep_c.c | 15 * initialization is performed.
|
12345678910>>...13
