Searched full:noise (Results 1 – 25 of 40) sorted by relevance
12
| /Zephyr-Core-3.5.0/dts/bindings/sensor/ |
| D | invensense,icp10125.yaml | 18 - "low-noise"
19 - "ultra-low-noise"
28 - "low-noise"
29 - "ultra-low-noise"
|
| D | st,lis2dw12-common.yaml | 173 low-noise:
177 This influences the noise density and the current consumption.
|
| D | nxp,fxos8700-common.yaml | 48 - 1 # Low noise, low power
|
| D | ti,tmag5170.yaml | 126 Enables additional sampling of the sensor data to reduce the noise
|
| /Zephyr-Core-3.5.0/dts/bindings/input/ |
| D | st,stmpe811.yaml | 69 is recommended at the touchscreen terminals for noise filtering.
103 Higher values result in more filtering of noise, but also introduce
108 at the cost of less noise filtering.
|
| /Zephyr-Core-3.5.0/tests/posix/pthread_pressure/ |
| D | testcase.yaml | 11 # Enabled for GitHub CI to reduce host scheduling noise while running
|
| /Zephyr-Core-3.5.0/drivers/entropy/ |
| D | Kconfig.esp32 | 15 numbers: noise from these radios are used to feed entropy in this
|
| D | Kconfig.nrf5 | 22 generator, based on internal thermal noise, that provides a
|
| D | Kconfig.stm32 | 14 generator, based on a continuous analog noise, that provides
|
| /Zephyr-Core-3.5.0/dts/bindings/rng/ |
| D | espressif,esp32-trng.yaml | 7 The TRNG uses the noise in the Wi-Fi/BT RF system. When Wi-Fi and BT are
|
| /Zephyr-Core-3.5.0/dts/bindings/pinctrl/ |
| D | gd,gd32-afio.yaml | 23 output speed is greater than 50MHz to reduce the I/O noise effects on
|
| D | nxp,lpc-iocon-pinctrl.yaml | 113 Digital input filter. Noise pulses below 10ms are filtered out.
|
| /Zephyr-Core-3.5.0/drivers/sensor/ina23x/ |
| D | Kconfig | 37 looking at measurement noise or debugging the SHUNT_CAL value.
|
| /Zephyr-Core-3.5.0/samples/sensor/fdc2x1x/ |
| D | README.rst | 21 noise susceptibility of the sensors. With the FDC2x1x innovative EMI resistant
22 architecture, performance can be maintained even in presence of high-noise environments.
|
| /Zephyr-Core-3.5.0/drivers/sensor/sht3xd/ |
| D | Kconfig | 60 noise level and energy consumption.
|
| /Zephyr-Core-3.5.0/samples/boards/nrf/mesh/onoff-app/ |
| D | prj.conf | 1 #CONFIG_INIT_STACKS=y # if set, lots of noise from mesh/adv.c: STACK_ANALYZE
|
| /Zephyr-Core-3.5.0/dts/bindings/net/wireless/ |
| D | generic-fem-two-ctrl-pins.yaml | 12 The CRX control pin is used to enable the Low Noise Amplifier
|
| /Zephyr-Core-3.5.0/dts/bindings/display/ |
| D | ftdi,ft800.yaml | 39 which helps reduce the system noise.
|
| /Zephyr-Core-3.5.0/samples/modules/tflite-micro/magic_wand/train/ |
| D | data_augmentation.py | 56 # Random noise
|
| /Zephyr-Core-3.5.0/soc/xtensa/intel_adsp/common/include/ |
| D | cavs-idc.h | 140 #define CAVS_L5_ANC BIT(12) /* Active Noise Cancellation */
|
| /Zephyr-Core-3.5.0/tests/lib/cmsis_dsp/common/ |
| D | math_helper.h | 53 * The function calculates signal to noise ratio for the reference output
|
| D | test_common.h | 22 #define ASSERT_MSG_SNR_LIMIT_EXCEED "signal-to-noise ratio " \
|
| /Zephyr-Core-3.5.0/drivers/input/ |
| D | input_xpt2046.c | 168 * releasing seem to cause just random noise in xpt2046_work_handler()
|
| /Zephyr-Core-3.5.0/include/zephyr/lorawan/ |
| D | lorawan.h | 166 * @param snr Signal to Noise ratio in dBm
|
| /Zephyr-Core-3.5.0/include/zephyr/drivers/modem/ |
| D | hl7800.h | 298 * @param sinr Signal to Interference plus Noise Ratio (dB)
|
12
