Searched full:interpreted (Results 1 – 25 of 76) sorted by relevance
1234
| /Zephyr-latest/arch/common/ |
| D | rom_start_offset.ld | 9 * as interpreted by GNU LD, but also compatible with LLVM LLD.
|
| /Zephyr-latest/include/zephyr/dt-bindings/clock/silabs/ |
| D | xg21-clock.h | 22 * interpreted correctly by the clock control driver.
|
| D | common-clock.h | 13 * interpreted correctly by the clock control driver.
|
| D | xg22-clock.h | 22 * interpreted correctly by the clock control driver.
|
| D | xg27-clock.h | 22 * interpreted correctly by the clock control driver.
|
| D | xg23-clock.h | 22 * interpreted correctly by the clock control driver.
|
| D | xg24-clock.h | 22 * interpreted correctly by the clock control driver.
|
| /Zephyr-latest/subsys/bindesc/ |
| D | gen_bindesc_build_time_h.cmake | 17 # remove leading zeros so that the output will not be interpreted as octal
|
| /Zephyr-latest/doc/hardware/peripherals/can/ |
| D | transceiver.rst | 18 These wires use the logic levels whereas the bus-level is interpreted
|
| /Zephyr-latest/include/zephyr/drivers/ethernet/ |
| D | eth_nxp_enet.h | 61 * data: opaque data, will be interpreted based on reason and target driver
|
| /Zephyr-latest/include/zephyr/bluetooth/mesh/ |
| D | health_srv.h | 32 * vendor. Vendor specific faults should be interpreted in the context
67 * vendor. Vendor specific faults should be interpreted in the context
100 * interpreted based on the accompanying Company ID. Test failures
|
| /Zephyr-latest/dts/bindings/lora/ |
| D | semtech,sx126x-base.yaml | 13 This signal is open-drain, active-low as interpreted by the
|
| D | semtech,sx127x-base.yaml | 15 active-low (SX1276/7/8/9) as interpreted by the modem.
|
| /Zephyr-latest/include/zephyr/drivers/pwm/ |
| D | max31790.h | 29 * to be interpreted as TACH target count. This basically is the number of internal
|
| /Zephyr-latest/include/zephyr/crypto/ |
| D | hash.h | 72 /** How certain fields are to be interpreted for this session.
|
| /Zephyr-latest/arch/arm64/core/ |
| D | coredump.c | 11 * To be interpreted by the target architecture specific block parser.
|
| /Zephyr-latest/subsys/logging/backends/ |
| D | Kconfig.net | 77 re-initialized." For Zephyr this is currently interpreted as the
|
| /Zephyr-latest/boards/google/dragonclaw/ |
| D | google_dragonclaw.dts | 101 * interpreted by GPIO driver as GPIO_DISCONNECTED, without setting the gpio as
|
| /Zephyr-latest/samples/boards/96boards/argonkey/microphone/ |
| D | README.rst | 93 .. note:: In case the character 0x0a is interpreted as NL and an 0x0d (CR) is added,
|
| /Zephyr-latest/tests/posix/c_lib_ext/src/ |
| D | getopt.c | 152 /* below should not be interpreted as "--long/-e" option */ in ZTEST()
259 /* below should be interpreted as "--long/-e" option */ in ZTEST()
|
| /Zephyr-latest/drivers/fpga/ |
| D | fpga_altera_agilex_bridge.h | 154 * customers and can only be interpreted by investigating the source code directly
|
| /Zephyr-latest/include/zephyr/drivers/ |
| D | hwinfo.h | 82 * sequence of bytes. The returned ID value is not supposed to be interpreted
|
| /Zephyr-latest/doc/kernel/ |
| D | timeutil.rst | 46 ``time_t`` and ``struct timespec``, which are generally interpreted as a
54 interpreted relative to a time scale which may be local time, UTC, or some
|
| /Zephyr-latest/samples/shields/x_nucleo_iks02a1/microphone/ |
| D | README.rst | 106 interpreted as NL and an 0x0d (CR) is added. If you don't remove it the audio stream would
|
| /Zephyr-latest/tests/subsys/usb/desc_sections/src/ |
| D | desc_sections.c | 202 * symbols that are normally interpreted as pointers.
|
1234
