Home
last modified time | relevance | path

Searched +full:int1 +full:- +full:gpios (Results 1 – 25 of 87) sorted by relevance

1234

/Zephyr-latest/drivers/sensor/nxp/fxos8700/
DKconfig1 # FXOS8700 6-axis accelerometer/magnetometer
4 # SPDX-License-Identifier: Apache-2.0
16 accelerometers then the Accelerometer-only mode should be selected."
25 bool "Accelerometer-only mode"
28 bool "Magnetometer-only mode"
53 depends on $(dt_compat_any_has_prop,$(DT_COMPAT_NXP_FXOS8700),int1-gpios) ||\
54 $(dt_compat_any_has_prop,$(DT_COMPAT_NXP_FXOS8700),int2-gpios)
67 bool "Data ready interrupt to INT1 pin"
70 Say Y to route data ready interrupt to INT1 pin. Say N to route to
93 bool "Pulse interrupt to INT1 pin"
[all …]
/Zephyr-latest/boards/shields/frdm_stbc_agm01/
Dfrdm_stbc_agm01.overlay3 * SPDX-License-Identifier: Apache-2.0
17 int1-gpios = <&arduino_header 8 GPIO_ACTIVE_LOW>;
18 int2-gpios = <&arduino_header 10 GPIO_ACTIVE_LOW>;
24 int1-gpios = <&arduino_header 11 GPIO_ACTIVE_LOW>;
25 int2-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>;
/Zephyr-latest/drivers/sensor/nxp/fxls8974/
DKconfig1 # FXLS8974 3-axis accelerometer
4 # SPDX-License-Identifier: Apache-2.0
27 depends on $(dt_compat_any_has_prop,$(DT_COMPAT_NXP_FXLS8974),int1-gpios) || \
28 $(dt_compat_any_has_prop,$(DT_COMPAT_NXP_FXLS8974),int2-gpios)
41 bool "Data ready interrupt to INT1 pin"
44 Say Y to route data ready interrupt to INT1 pin. Say N to route to
/Zephyr-latest/tests/drivers/build_all/sensor/
Dspi.dtsi4 * SPDX-License-Identifier: Apache-2.0
16 spi-max-frequency = <0>;
17 int1-gpios = <&test_gpio 0 0>;
23 spi-max-frequency = <0>;
24 int1-gpios = <&test_gpio 0 0>;
30 spi-max-frequency = <0>;
36 spi-max-frequency = <0>;
37 int-gpios = <&test_gpio 0 0>;
43 spi-max-frequency = <0>;
49 spi-max-frequency = <0>;
[all …]
Di2c.dtsi4 * SPDX-License-Identifier: Apache-2.0
9 #include <zephyr/dt-bindings/sensor/lsm6dsv16x.h>
10 #include <zephyr/dt-bindings/sensor/lsm6dso.h>
11 #include <zephyr/dt-bindings/sensor/lsm6dso16is.h>
12 #include <zephyr/dt-bindings/sensor/lps22hh.h>
13 #include <zephyr/dt-bindings/sensor/lps2xdf.h>
14 #include <zephyr/dt-bindings/sensor/lis2ds12.h>
15 #include <zephyr/dt-bindings/sensor/lis2dw12.h>
16 #include <zephyr/dt-bindings/sensor/ism330dhcx.h>
17 #include <zephyr/dt-bindings/sensor/iis2dlpc.h>
[all …]
/Zephyr-latest/dts/bindings/sensor/
Dnxp,fxas21002-common.yaml2 # SPDX-License-Identifier: Apache-2.0
4 description: FXAS21002 3-axis gyroscope sensor
6 include: sensor-device.yaml
9 reset-gpios:
10 type: phandle-array
17 int1-gpios:
18 type: phandle-array
20 INT1 pin
25 int2-gpios:
26 type: phandle-array
Dbosch,bma4xx-common.yaml2 # SPDX-License-Identifier: Apache-2.0
5 int1-gpios:
6 type: phandle-array
8 Identifies pin for the INT1 signal on the sensor. The sensor
Dnxp,fxls8974-common.yaml2 # SPDX-License-Identifier: Apache-2.0
4 description: FXLS8974 3-axis accelerometer sensor
6 include: sensor-device.yaml
9 reset-gpios:
10 type: phandle-array
17 int1-gpios:
18 type: phandle-array
20 INT1 pin
25 int2-gpios:
26 type: phandle-array
[all …]
Dbosch,bmi160.yaml2 # SPDX-License-Identifier: Apache-2.0
6 include: sensor-device.yaml
9 int-gpios:
10 type: phandle-array
12 This property specifies the connection for INT1, because the
13 Zephyr driver maps all interrupts to INT1. The signal defaults
Dbosch,bmi323.yaml2 # SPDX-License-Identifier: Apache-2.0
6 include: ["spi-device.yaml", "sensor-device.yaml"]
9 int-gpios:
10 type: phandle-array
12 This property specifies the connection for INT1, because the
13 Zephyr driver maps all interrupts to INT1. The signal defaults
Dst,iis328dq-common.yaml3 # SPDX-License-Identifier: Apache-2.0
5 include: sensor-device.yaml
8 int1-gpios:
9 type: phandle-array
16 int2-gpios:
17 type: phandle-array
24 drdy-int-pad:
34 - 1 # drdy is generated on INT1
35 - 2 # drdy is generated on INT2
37 threshold-int-pad:
[all …]
Dst,lis2dux12-common.yaml2 # SPDX-License-Identifier: Apache-2.0
5 When setting the odr, power-mode, and range properties in a .dts or .dtsi file you may include
8 #include <zephyr/dt-bindings/sensor/st_lis2dux12.h>
11 power-mode = <LIS2DUX12_OPER_MODE_LOW_POWER>;
16 include: sensor-device.yaml
19 int1-gpios:
20 type: phandle-array
22 INT1 pin
27 int2-gpios:
28 type: phandle-array
[all …]
Dbosch,bmi08x-accel.yaml2 # SPDX-License-Identifier: Apache-2.0
6 include: sensor-device.yaml
9 int-gpios:
10 type: phandle-array
16 int1-map-io:
19 Bit[0]: Map Interrupt A to INT1, Accel Data Ready
20 Bit[1]: Map Interrupt B to INT1
21 Bit[2]: Map Interrupt C to INT1
23 int2-map-io:
30 int1-conf-io:
[all …]
Dadi,adxl367-common.yaml2 # SPDX-License-Identifier: Apache-2.0
4 include: sensor-device.yaml
19 - 0
20 - 1
21 - 2
22 - 3
23 - 4
24 - 5
26 int1-gpios:
27 type: phandle-array
[all …]
Dst,lis2du12-common.yaml2 # SPDX-License-Identifier: Apache-2.0
5 When setting the accel-range, accel-odr, properties in a .dts or .dtsi
9 #include <zephyr/dt-bindings/sensor/lis2du12.h>
14 accel-range = <LIS2DU12_DT_FS_16G>;
15 accel-odr = <LIS2DU12_DT_ODR_AT_50Hz>;
18 include: sensor-device.yaml
21 int1-gpios:
22 type: phandle-array
24 INT1 pin
30 int2-gpios:
[all …]
Dbosch,bma280.yaml2 # SPDX-License-Identifier: Apache-2.0
6 https://www.bosch-sensortec.com/products/motion-sensors/accelerometers/bma280.html
10 include: [sensor-device.yaml, i2c-device.yaml]
13 int1-gpios:
14 type: phandle-array
16 Identifies pin for the INT1 signal on the sensor. The sensor
19 is-bmc150:
23 capability provided by the BMC150 6-axis eCompass. This affects
Dadi,adxl362.yaml2 # SPDX-License-Identifier: Apache-2.0
4 description: ADXL362 3-axis SPI accelerometer
8 include: [sensor-device.yaml, spi-device.yaml]
11 int1-gpios:
12 type: phandle-array
14 The INT1 signal defaults to active high as produced by the
18 wakeup-mode:
27 Enter Wake-Up mode when inactivity is detected,
Dst,lis2dh-common.yaml2 # SPDX-License-Identifier: Apache-2.0
5 When setting the int1-gpio-config/int2-gpio-config and anym-mode properties
9 #include <zephyr/dt-bindings/sensor/lis2dh.h>
14 int1-gpio-config = <LIS2DH_DT_GPIO_INT_LEVEL_LOW>;
15 int2-gpio-config = <LIS2DH_DT_GPIO_INT_LEVEL_LOW>;
16 anym-mode = <LIS2DH_DT_ANYM_6D_POSITION>;
19 include: sensor-device.yaml
22 irq-gpios:
23 type: phandle-array
25 The INT1 and (optional) INT2 signal connections. These signals
[all …]
Dst,lis2de12-common.yaml2 # SPDX-License-Identifier: Apache-2.0
5 When setting the accel-range, accel-odr, properties in a .dts or .dtsi
9 #include <zephyr/dt-bindings/sensor/lis2de12.h>
14 accel-range = <LIS2DE12_DT_FS_16G>;
15 accel-odr = <LIS2DE12_DT_ODR_AT_100Hz>;
18 include: sensor-device.yaml
21 int1-gpios:
22 type: phandle-array
24 INT1 pin
30 int2-gpios:
[all …]
/Zephyr-latest/dts/bindings/rtc/
Dnxp,pcf8563.yaml2 # SPDX-License-Identifier: Apache-2.0
9 - name: rtc-device.yaml
10 - name: i2c-device.yaml
13 int1-gpios:
14 type: phandle-array
16 GPIO connected to the PC8563 INT1 interrupt output. This signal is open-drain, active low.
/Zephyr-latest/drivers/sensor/nxp/fxas21002/
DKconfig1 # FXAS21002 3-axis gyroscope
4 # SPDX-License-Identifier: Apache-2.0
23 pre-production devices can have a different value. It is unlikely you
32 0: +/-2000 dps (62.5 mdps/LSB)
33 1: +/-1000 dps (31.25 mdps/LSB)
34 2: +/-500 dps (15.625 mdps/LSB)
35 3: +/-250 dps (7.8125 mdps/LSB)
62 depends on $(dt_compat_any_has_prop,$(DT_COMPAT_NXP_FXAS21002),int1-gpios) ||\
63 $(dt_compat_any_has_prop,$(DT_COMPAT_NXP_FXAS21002),int2-gpios)
78 bool "Data ready interrupt to INT1 pin"
[all …]
/Zephyr-latest/drivers/sensor/st/iis3dhhc/
DKconfig4 # SPDX-License-Identifier: Apache-2.0
15 Enable driver for IIS3DHHC SPI-based accelerometer sensor.
31 depends on $(dt_compat_any_has_prop,$(DT_COMPAT_ST_IIS3DHHC),irq-gpios)
37 depends on $(dt_compat_any_has_prop,$(DT_COMPAT_ST_IIS3DHHC),irq-gpios)
66 bool "Data ready interrupt to INT1 pin"
70 Say Y to route data ready interrupt to INT1 pin. Say N to route to
/Zephyr-latest/drivers/sensor/bosch/bma280/
DKconfig4 # SPDX-License-Identifier: Apache-2.0
12 Enable driver for BMA280 I2C-based triaxial accelerometer sensor
29 depends on $(dt_compat_any_has_prop,$(DT_COMPAT_BOSCH_BMA280),int1-gpios)
35 depends on $(dt_compat_any_has_prop,$(DT_COMPAT_BOSCH_BMA280),int1-gpios)
64 bool "+/-2g"
67 bool "+/-4g"
70 bool "+/-8g"
73 bool "+/-16g"
/Zephyr-latest/drivers/sensor/st/lsm6dsv16x/
DKconfig1 # ST Microelectronics LSM6DSV16X 6-axis IMU sensor driver
4 # SPDX-License-Identifier: Apache-2.0
45 depends on $(dt_compat_any_has_prop,$(DT_COMPAT_ST_LSM6DSV16X),int1-gpios) ||\
46 $(dt_compat_any_has_prop,$(DT_COMPAT_ST_LSM6DSV16X),int2-gpios) ||\
53 depends on $(dt_compat_any_has_prop,$(DT_COMPAT_ST_LSM6DSV16X),int1-gpios) ||\
54 $(dt_compat_any_has_prop,$(DT_COMPAT_ST_LSM6DSV16X),int2-gpios) ||\
/Zephyr-latest/boards/element14/warp7/
Dwarp7_mcimx7d_m4.dts4 * SPDX-License-Identifier: Apache-2.0
7 /dts-v1/;
10 #include "warp7-pinctrl.dtsi"
11 #include <zephyr/dt-bindings/input/input-event-codes.h>
27 zephyr,shell-uart = &uart2;
31 compatible = "gpio-keys";
33 gpios = <&gpio7 1 GPIO_ACTIVE_LOW>;
42 current-speed = <115200>;
43 modem-mode = <0>;
44 pinctrl-0 = <&uart2_default>;
[all …]

1234