Searched full:gives (Results 1 – 25 of 166) sorted by relevance
1234567
| /Zephyr-latest/dts/bindings/sensor/ |
| D | ti,ina219.yaml | 75 Lowering the resolution of the ADC gives less accurate readings but
78 Averaging over multiple samples gives more stable readings but adds
111 Lowering the resolution of the ADC gives less accurate readings but
114 Averaging over multiple samples gives more stable readings but adds
|
| D | nxp,s32-qdec.yaml | 62 This gives the logic triggers configuration of TRGMUX module.
86 This array gives the configuration for each of the four outputs of LCU module.
|
| /Zephyr-latest/tests/kernel/fifo/fifo_usage/src/ |
| D | main.c | 17 * gives the semaphore for Test Thread to continue. Once the control
28 * Tests the ISR interfaces. Test thread puts items into fifo2 and gives
30 * puts items into fifo1. Child thread gives back control to the Test thread
140 * gives the semaphore for Test Thread to continue. Once the control
209 * and gives control to the Child thread. Child thread gets items from
210 * fifo2 and then puts items into fifo1. Child thread gives back control
|
| /Zephyr-latest/dts/bindings/spi/ |
| D | andestech.atcspi200.yaml | 8 This binding gives a representation of Andes ATCSPI200 SPI controller
|
| D | ambiq,spi-bleif.yaml | 5 This binding gives a representation of SPI controller in some Ambiq
|
| /Zephyr-latest/dts/bindings/serial/ |
| D | nxp,imx-iuart.yaml | 2 This binding gives a base representation of the NXP iMX IUART
|
| D | cdns,uart.yaml | 6 description: This binding gives a base representation of the CADENCE UART IP6528
|
| /Zephyr-latest/samples/net/wifi/shell/ |
| D | overlay-enterprise.conf | 8 # for MbedTLS gives us more control over the heap size.
|
| D | overlay-enterprise-variable-bufs.conf | 7 # for MbedTLS gives us more control over the heap size.
|
| /Zephyr-latest/dts/bindings/gpio/ |
| D | ite,it8xxx2-gpio.yaml | 4 description: This binding gives a base representation of the ITE gpio
|
| D | ite,it8xxx2-gpiokscan.yaml | 4 description: This binding gives a base representation of the ITE kscan pins as gpio
|
| D | ite,it8xxx2-gpio-v2.yaml | 4 description: This binding gives a base representation of the ITE gpio
|
| /Zephyr-latest/drivers/clock_control/ |
| D | Kconfig.litex | 12 It gives ability to change clock parameters
|
| /Zephyr-latest/tests/bsim/bluetooth/mesh/tests_scripts/friendship/ |
| D | lpn_disable.sh | 7 # Check that disabling LPN gives correct behaviour.
|
| /Zephyr-latest/drivers/interrupt_controller/ |
| D | Kconfig.clic | 24 The selective hardware vectoring extension gives users the flexibility
|
| /Zephyr-latest/dts/bindings/display/ |
| D | sharp,ls0xx.yaml | 23 datasheet of particular display. Higher frequency gives better
|
| /Zephyr-latest/dts/bindings/pinctrl/ |
| D | renesas,rcar-pfc.yaml | 6 This binding gives a base representation of the R-Car pins configuration.
77 This binding gives a base representation of the R-Car pins configuration.
|
| D | snps,emsdp-pinctrl.yaml | 31 This binding gives a base representation of the EMSDP pins
|
| D | ti,k3-pinctrl.yaml | 31 This binding gives a base representation of the TI K3
|
| D | sifive,pinctrl.yaml | 38 This binding gives a base representation of the SiFive FE310 pins
|
| /Zephyr-latest/boards/makerdiary/nrf52832_mdk/doc/ |
| D | index.rst | 10 The kit gives access to 24 I/Os and interfaces via headers and has a
|
| /Zephyr-latest/dts/bindings/stepper/adi/ |
| D | adi,trinamic-stallguard.yaml | 17 optimum measurement range for readout. A lower value gives a higher sensitivity.
|
| /Zephyr-latest/dts/bindings/watchdog/ |
| D | gd,gd32-fwdgt.yaml | 19 The following equation gives the maximum timeout value
|
| /Zephyr-latest/dts/bindings/sdhc/ |
| D | zephyr,sdhc-spi-slot.yaml | 13 delay gives the card time to power up or down fully. It can be increased
|
| /Zephyr-latest/dts/bindings/bluetooth/ |
| D | zephyr,bt-hci-spi.yaml | 32 associated with that header. This delay gives the controller time to configure
|
1234567
