Searched full:fully (Results 1 – 25 of 208) sorted by relevance
123456789
| /Zephyr-latest/samples/basic/fade_led/ |
| D | README.rst | 12 The LED starts off increases its brightness until it is fully or nearly fully
|
| /Zephyr-latest/modules/cmsis-nn/ |
| D | Kconfig | 43 bool "Fully Connected"
46 Collection of fully-connected and matrix multiplication functions.
|
| /Zephyr-latest/dts/bindings/timer/ |
| D | mediatek,ostimer64.yaml | 6 # This clock hardware is almost fully described by its register block,
|
| /Zephyr-latest/doc/develop/toolchains/ |
| D | arm_compiler.rst | 48 fully supported by the CMake linker script generator.
51 that relies on GNU intrinsics and have not yet been updated to work fully
|
| /Zephyr-latest/drivers/i2c/ |
| D | Kconfig.mcux | 24 must be enabled to allow the driver to fully recover.
|
| /Zephyr-latest/drivers/serial/ |
| D | Kconfig.xmc4xxx | 27 need to be fully flushed so that the interrupt will trigger again.
|
| /Zephyr-latest/cmake/linker/lld/ |
| D | linker_libraries.cmake | 11 # When new link principle is fully introduced, then the below condition can
|
| /Zephyr-latest/dts/bindings/adc/ |
| D | st,stm32-adc.yaml | 104 - "NOT_FULLY_CONFIGURABLE": Not fully configurable sequencer
105 - "FULLY_CONFIGURABLE": Fully configurable sequencer
|
| /Zephyr-latest/boards/makerdiary/nrf52832_mdk/doc/ |
| D | index.rst | 6 The nrf52832_mdk board is a fully open-source, versatile single board
|
| /Zephyr-latest/dts/bindings/clock/ |
| D | st,stm32f411-plli2s-clock.yaml | 7 Fully configurable I2S dedicated PLL.
|
| /Zephyr-latest/cmake/sca/eclair/ECL/ |
| D | adopted_deviations.ecl | 3 -doc="Selection for reports that are fully contained in adopted code."
6 …ble. In addition, adopted code is assumed to work as is. Reports that are fully contained in adopt…
|
| /Zephyr-latest/dts/bindings/sdhc/ |
| D | zephyr,sdhc-spi-slot.yaml | 13 delay gives the card time to power up or down fully. It can be increased
|
| D | sdhc.yaml | 51 delay gives the card time to power up or down fully
|
| /Zephyr-latest/samples/modules/tflite-micro/hello_world/train/ |
| D | README.md | 57 simple feed forward deep neural network with 2 fully connected layers with
58 ReLu activations and a final fully connected output layer with as shown below.
|
| /Zephyr-latest/doc/hardware/peripherals/sensor/ |
| D | power_management.rst | 14 Most likely the API sensors should use for their fully suspended/resume power states is
|
| /Zephyr-latest/boards/makerdiary/nrf52840_mdk/doc/ |
| D | index.rst | 10 The development kit comes with a fully integrated debugger (also known as
|
| /Zephyr-latest/boards/shields/seeed_xiao_round_display/doc/ |
| D | index.rst | 10 XIAO development boards. It features a fully covered touch screen on one side,
|
| /Zephyr-latest/samples/subsys/usb/audio/headset/ |
| D | README.rst | 19 software and hardware specific information which allow to fully
|
| /Zephyr-latest/cmake/linker/ld/ |
| D | linker_libraries.cmake | 16 # When new link principle is fully introduced, then the below condition can
|
| /Zephyr-latest/samples/subsys/usb/audio/headphones_microphone/ |
| D | README.rst | 20 software and hardware specific information which allow to fully
|
| /Zephyr-latest/include/zephyr/net/http/ |
| D | service.h | 105 * IPv4 or IPv6 format a fully-qualified hostname or a virtual host. If left NULL, the listening
127 * IPv4 or IPv6 format a fully-qualified hostname or a virtual host. If left NULL, the listening
155 * IPv4 or IPv6 format a fully-qualified hostname or a virtual host. If left NULL, the listening
181 * IPv4 or IPv6 format a fully-qualified hostname or a virtual host. If left NULL, the listening
|
| /Zephyr-latest/drivers/i2s/ |
| D | i2s_ll_stm32.h | 62 /* checks that DMA Tx packet is fully transmitted over the I2S */
|
| /Zephyr-latest/samples/fuel_gauge/max17048/ |
| D | README.rst | 25 * Total time until battery is fully charged or discharged
|
| /Zephyr-latest/arch/arm64/core/cortex_r/ |
| D | Kconfig | 25 As a result of this, the ARMv8-R MPU needs to fully partition the
|
| /Zephyr-latest/samples/boards/ti/cc13x2_cc26x2/system_off/ |
| D | README.rst | 38 1. Unplug the USB cable from the LaunchPad and reconnect it to fully
|
123456789
