Home
last modified time | relevance | path

Searched full:defaults (Results 1 – 25 of 305) sorted by relevance

12345678910>>...13

/Zephyr-latest/dts/bindings/input/
Dkbd-matrix-common.yaml24 to never exit poll mode. Defaults to 5ms if unspecified.
30 stable, defaults to poll-period-ms value if unspecified.
36 How long to wait before going from polling back to idle state. Defaults
43 Debouncing time for a key press event. Defaults to 10ms if unspecified.
49 Debouncing time for a key release event. Defaults to 20ms if unspecified.
55 Delay between setting column output and reading the row values. Defaults
Despressif,esp32-touch-sensor.yaml83 If not specified defaults to ESP32_TOUCH_FILTER_MODE_IIR_16.
90 If not specified defaults to 1.
97 If not specified defaults to ESP32_TOUCH_FILTER_NOISE_THR_4_8TH.
104 If not specified defaults to 4.
111 If not specified defaults to ESP32_TOUCH_FILTER_SMOOTH_MODE_IIR_2.
126 If not specified defaults to 20.
Danalog-axis.yaml36 milliseconds. Defaults to 15ms if unspecified.
50 Minimum value to output on input events. Defaults to 0 if unspecified.
56 Maximum value to output on input events. Defaults to 255 if
65 center. Defaults to 0, no deadzone.
Dhynitron,cst816s.yaml14 The irq signal defaults to active low as produced by the
21 The reset signal defaults to active low to the
/Zephyr-latest/dts/bindings/sensor/
Dvishay,vcnl36825t.yaml22 Defaults to sensor reset value.
37 Defaults to 40 ms which is supported in both normal and low-power mode.
45 Defaults to sensor reset value.
53 Defaults to sensor reset value.
62 Defaults to sensor reset value.
70 Defaults to minimum allowed value.
113 Defaults to "normal" as this is the easiest configurable mode.
121 Defaults to sensor reset value
Dnxp,fxas21002-common.yaml13 This pin defaults to active low when consumed by the sensor.
21 This pin defaults to active low when produced by the sensor.
29 This pin defaults to active low when produced by the sensor.
Dnxp,fxls8974-common.yaml13 This pin defaults to active high when consumed by the sensor.
21 This pin defaults to active low when produced by the sensor.
29 This pin defaults to active low when produced by the sensor.
Dti,tmag5273.yaml36 Defaults to continuous sampling (TMAG5273_DT_OPER_MODE_CONTINUOUS).
47 Defaults to measure all axis (TMAG5273_DT_AXIS_XYZ).
73 Defaults to lower range (higher resolution; TMAG5273_DT_AXIS_RANGE_LOW).
93 Defaults to none (TMAG5273_DT_TEMP_COEFF_NONE).
117 Defaults to no additional calculations (TMAG5273_DT_ANGLE_MAG_NONE).
131 Defaults to 1st channel.
147 Defaults to 2x averaging (TMAG5273_DT_AVERAGING_2X).
Dst,stts22h-i2c.yaml27 This pin defaults to active high when produced by the sensor.
36 Valid range is 0 to 255. It defaults to 0 (alarm off) which is
47 Valid range is 0 to 255. It defaults to 0 (alarm off) which is
Dwe,wsen-hids-2525020210002.yaml23 Defaults to mid, which is a good compromise between
40 Defaults to OFF, since this option is valid for high precision
Dst,lis2dux12-common.yaml24 This pin defaults to active high when produced by the sensor.
32 This pin defaults to active high when produced by the sensor.
46 mandatory and if not present it defaults to 1 which is the
Dst,lis2du12-common.yaml26 This pin defaults to active high when produced by the sensor.
35 This pin defaults to active high when produced by the sensor.
50 mandatory and if not present it defaults to 1 which is the
Dst,iis328dq-common.yaml13 This pin defaults to active high when produced by the sensor. The property value should ensure
21 This pin defaults to active high when produced by the sensor. The property value should ensure
/Zephyr-latest/dts/bindings/watchdog/
Dnxp,s32-swt.yaml27 Defaults to access enabled for all masters (hardware reset value).
44 Defaults to "fixed" (hardware reset value).
51 Defaults to 0 (hardware reset value).
66 Defaults to unlocked (hardware reset value).
/Zephyr-latest/dts/bindings/display/
Dst,stm32-ltdc.yaml58 description: First pixel in x direction on layer 0. Defaults to 0.
62 description: Last pixel in x direction on layer 0. Defaults to width.
66 description: First pixel in y direction on layer 0. Defaults to 0.
70 description: Last pixel in y direction on layer 0. Defaults to height.
Dsolomon,ssd16xx-common.yaml47 defaults loaded from the controllers OTP memory.
50 has been specified. That profile may be empty to use the defaults
/Zephyr-latest/dts/bindings/mfd/
Dnordic,npm6001.yaml30 description: Input type for BUCK_MODE0 pin. Defaults IC boot-time value.
40 description: Input type for BUCK_MODE1 pin. Defaults IC boot-time value.
50 description: Input type for BUCK_MODE2 pin. Defaults IC boot-time value.
/Zephyr-latest/soc/andestech/ae350/
DKconfig.defconfig7 # SoC defaults should be parsed before SoC Series defaults, because SoCs usually
/Zephyr-latest/soc/nxp/imxrt/
DKconfig.defconfig7 # can override the defaults given here
87 # what the ztest_thread_stack defaults to.
94 # defaults specific for the M7 core
/Zephyr-latest/dts/bindings/mipi-dbi/
Dmipi-dbi-device.yaml34 MIPI DBI tearing enable signal mode. Defaults to disabled.
45 tearing enable synchronization signal is seen. Defaults to 0 since most
/Zephyr-latest/tests/drivers/regulator/voltage/dts/bindings/
Dtest-regulator-voltage.yaml38 Number of ADC readings to average. Defaults to 1 (no average).
44 Delay between voltage set and ADC read. Defaults to 0 (no delay).
/Zephyr-latest/dts/bindings/auxdisplay/
Dsparkfun,serlcd.yaml42 Delay in milliseconds (defaults to 10ms if not set) after a normal command was sent.
52 Delay in milliseconds (defaults to 50ms if not set) after a special command was sent.
/Zephyr-latest/samples/bluetooth/hci_uart/boards/
Dnrf9160dk_nrf52840.conf1 # Override prj.conf defaults
/Zephyr-latest/samples/bluetooth/hci_uart_3wire/boards/
Dnrf9160dk_nrf52840.conf1 # Override prj.conf defaults
/Zephyr-latest/soc/nxp/imx/
DKconfig.defconfig7 # can override the defaults given here

12345678910>>...13